横向槽结构对气膜冷却效果影响的数值研究

推进技术 ›› 2011, Vol. 32 ›› Issue (2): 253-260.

横向槽结构对气膜冷却效果影响的数值研究

戴萍,林枫

青岛科技大学机电工程学院,山东青岛 266061 ;哈尔滨工程大学动力与能源学院,黑龙江哈尔滨 150001;中国船舶重工集团第703研究所燃气轮机研究室,黑龙江哈尔滨 150036

发布日期:2021-08-15
作者简介:戴萍(1971—),女,博士,讲师,研究领域为发动机高温部件传热及冷却技术。E-mail:daiping936@yahoo.com.cn
基金资助:
山东省自然科学基金(ZR2010EM069)。

Numerical investigation on the influence of transverse slotconfigurations on film cooling effect

Coll. of Electromechanical Engineering, Qingdao Univ. of Science and Technology, Qingdao 266061, China ;Coll. of Power and Energy Engineering, Harbin Univ. of Engineering, Harbin 150001, China;Dept. of Gas Turbine, China Shipbuilding Industry Corporation 7th Inst.,Harbin 150036,China

Published:2021-08-15

摘要/Abstract

摘要： 基于有限体积法对三维定常不可压缩N-S方程进行离散,采用两层k-ε湍流模型,在吹风比M为0.6,1.2和1.8的情况下,数值研究了6种不同横向槽结构对气膜冷却效果的影响,并与常规圆柱孔进行了比较。结果表明:在任何吹风比下,所有开槽孔的冷却效率均高于圆柱孔；在低吹风比时,6种开槽孔的冷却效率相差不大,随着吹风比的增大,不同开槽孔冷却效率的变化趋势不尽相同；具有中等开槽深度(0.75D)和最大开槽宽度(3D)的开槽孔,气膜冷却效果最佳,而具有最大开槽深度(1D)的开槽孔,气膜冷却效果较差；横向槽的存在使冷气射流在流出气膜后面积突扩,动量降低,气膜出流向主流的垂直穿透能力随之降低,射流本身流动的扩散以及射流在流入横向槽中受到主流对其向下的压制作用较大,反向涡旋对的强度不同程度地受到了抑制,增强了壁面的冷却效果。

关键词: 气膜冷却;横向槽;冷却效率;吹风比;数值仿真

Abstract: Influence of transverse slot configuration on film cooling effectiveness at the blade were investigated using a three-dimensional finite volume method and multi-block technique at the blowing ratio ranging from 0.6 to 1.8. Previous successful application of a two-layer turbulence model to cylindrical is extended to predict film cooling for the six kinds of trench hole. Also, flim cooling performance from transverse slot was compared with that of cylindrical hole. The results showed that effectiveness of all of trench hole was better than that of cylindrical hole at any blowing ratio. Film cooling effectiveness of several kinds of trench hole was almost consistent at low blowing ratio. Change trend of effectiveness of different trench hole was unlikeness along with increasing blowing ratio. Cooling effect of trench hole with moderate depth and maximal width was best among other cases and cooling effect of trench hole with maximal depth was reduced. It is also found that the momentum was depressed on account of area of jet flow abruptly increased when the jet was injected into the slot. The penetration of the film secondary flow into the mainstream flow was suppressed and the secondary flow was pushed downwards onto the surface, so the counter rotating vortex pairs have been weakened for the trench hole and results in a better coolant protection.

Key words: Film cooling; Transverse slot; Cooling effectiveness; Blowing ratio; Numerical simulation

戴萍,林枫. 横向槽结构对气膜冷却效果影响的数值研究[J]. 推进技术, 2011, 32(2): 253-260.

参考文献

[2] Lu Y P, Nasir H, Ekkad S V.Film cooling from a row of holes embedded in transverse slots[R].ASME 2005-GT-68598.
[3] Yu Y.Effect of hole configurations on film cooling from cylindrical inclined holes for the application to gas turbine blades[D].Baton Rouge:Louisiana State University, 2007.
[4] 左红,王鹏,武卫,等.横向槽深度对气膜孔冷却性能影响数值研究[J].机械科学与技术, 8,7(9):1252-1260.
[5] 蒋永健,何立明,于锦禄,等.利用横向槽改善气膜冷却效率的数值研究[J].推进技术, 8,9(3):286-289.(JIANG Yong-jian, HE Li-ming, YU Jin-lu, et al.Numerical investigation on improving film cooling effectiveness with transverse slots[J].Journal of Propulsion Technology, 8,9(3):286-289.)
[6] 章大海,陈秋炀,曾敏,等.不同横槽结构对气膜冷却效率影响的数值研究[J].航空动力学报, 8,3(4):611-616.
[7] Azzi A, Lakehal D.Perspectives in modeling film cooling of turbine blades by transcending conventional two-equation turbulence models[J].ASME Journal of Turbomchinery, 2,4:472-484.
[8] Kim J, Moin P, Moser R.Turbulence statistics in fully developed channel flow at low Reynolds number[J].Journal Fluid Mechanical, 7,7:133-166.
[9] Rodi W, Mansour N N, Michelassi V.One equation near wall turbulence modeling with the aid of direct simulation data[J].ASME Journal of Engineering for Fluids, 3,5:196-205.
[10] Lu Xiaochen, Jiang Peixue, Sugishita H, et al.Conjugate heat transfer analysis of film cooling flows[J].Journal of Thermal Science, 6,5(1):85-91.
[11] Schmid D L, Sen B, Bogare D G.Film cooling with compound angle holes:adiabatic effectiveness[R].ASME 91-GT-127.
[12] 戴萍, 林枫.气膜孔形状对涡轮叶片气膜冷却效果的影响[J].热能动力工程, 9,4(5):560-565.
[13] Lakehal D, Theodoridis G, Rodi W.Three-dimensional flow and heat transfer calculation of film cooling at the leading edge of a symmetrical turbine blade model[J].International Journal of Heat and Fluid Flow, 1,2(2):113-122.