高主流湍流度下密度比对涡轮导叶全气膜冷却特性的影响

doi:10.13675/j.cnki. tjjs. 180438

推进技术 ›› 2019, Vol. 40 ›› Issue (7): 1585-1593.DOI: 10.13675/j.cnki. tjjs. 180438

高主流湍流度下密度比对涡轮导叶全气膜冷却特性的影响

西北工业大学动力与能源学院

发布日期:2021-08-15
作者简介:付仲议，博士，研究领域为航空发动机高温部件冷却技术。E-mail：252922326@qq.com
基金资助:
国家重点基础研究发展规划资助项目 2013CB035702国家重点基础研究发展规划资助项目（2013CB035702）。

Effects of Density Ratio on Full Film Cooling Characteristics of Turbine Guide Vane with High Mainstream Turbulence

School of Power and Energy,Northwestern Polytechnical University,Xi’an 710072,China

Published:2021-08-15

摘要/Abstract

摘要： 为了研究高主流湍流度下二次流密度比对涡轮导叶全气膜冷却特性的影响，使用热色液晶测量了在主流湍流度为15%，二次流密度比为1.0和1.5下三维涡轮导叶的气膜冷却效率和换热系数。二次流与主流质量流量比为7.0%和12.5%。结果表明：二次流密度比增大可以降低冷气射流的动量，小流量比工况下，在叶片前缘和压力面前半段，动量较低的二次流在高主流湍流度的影响下更易耗散，增大二次流密度比使冷却效率明显降低；大流量比工况下，二次流动量降低使气膜孔后区域冷气贴附性增强，气膜冷却效率和冷气覆盖效果均得到提升。小流量比工况下，二次流密度比增大对叶片表面换热的影响较小；大流量比工况下，二次流密度比增大使吸力面中弦区域和压力面后半段的平均换热系数比分别降低15%和25%。

关键词: 主流湍流度;密度比;涡轮导叶;气膜冷却效率;换热系数;液晶

Abstract: In order to study the effects of the secondary flow density ratio on the full film cooling characteristics of turbine guide vane with high mainstream turbulence, the film cooling effectiveness and heat transfer coefficient of a three-dimensional turbine guide vane model were measured using transient liquid crystal technique. The mainstream turbulence is 15% and the secondary flow density ratios are 1.0 and 1.5. The secondary flow mass flow rate ratios are 7.0% and 12.5%. The results show that the high density ratio decreases the momentum of film jets: in low mass flow rate ratio condition, the coolant with lower momentum on the leading edge and the first half of pressure side is easier to dissipate, which decreases the film cooling effectiveness; in high mass flow rate ratio condition, the decrease of secondary flow momentum enhances the attachment of coolant in the downstream of film holes, which increases the film cooling effectiveness and film coverage. In low mass flow rate ratio condition, the effect of the high secondary flow density ratio on the heat transfer of vane is insignificant; in high mass flow rate ratio condition, the increase of secondary flow density ratio decreases the average heat transfer coefficient ratio in the middle chord region of suction side and the second half of pressure side by 15% and 25%, respectively.

Key words: Mainstream turbulence intensity;Density ratio;Turbine guide vane;Film cooling effectiveness;Heat transfer coefficient;Liquid crystal

. 高主流湍流度下密度比对涡轮导叶全气膜冷却特性的影响[J]. 推进技术, 2019, 40(7): 1585-1593.

参考文献

[1] Han J C, Dutta S， Ekkad S V. Gas Turbine Heat Transfer and Cooling Technology[M]. USA: Chemical Rubber Company Press， 2012.
[2] Eckert E R G， Goldstein R J， Ramsey J W. Film Cooling with Injection Through Holes: Adiabatic Wall Temperatures Downstream of a Circular Hole[J]. Journal of Engineering for Power， 1968， 90: 384-393.
[3] Goldstein R J. Film Cooling[J]. Advances in Heat Transfer， 1971， 7(1): 321-379.
[4] Mayhew J E， Baughn J W， Byerley A R. The Effect of Freestream Turbulence on Film Cooling Adiabatic Effectiveness[J]. International Journal of Heat and Fluid Flow， 2003， 24(5): 669-679.
[5] Pedersen D R， Eckert E R G， Goldstein R J. Film Cooling with Large Density Differences Between the Mainstream and the Secondary Fluid Measured by the Heat-Mass Transfer Analogy[J]. Journal of Heat Transfer， 1977， 99(4): 620-627.
[6] Sinha A K. Film-Cooling Effectiveness Downstream of a Single Row of Holes with Variable Density Ratio[J]. Journal of Turbomachinery， 1991， 113(3): 442-449.
[7] Schreivogel P， Kr?ss B， Pfitzner M. Density Ratio Effects on the Flow Field Emanating from Cylindrical Effusion and Trenched Film Cooling Holes[R]. ASME GT2014-25143.
[8] Konopka M， Jessen W， Meinke M， et al. Large-Eddy Simulation of Film Cooling in an Adverse Pressure Gradient Flow[R]. ASME GT2012-69026.
[9] Goldstein R J， Stone L D. Row-of-Holes Film Cooling of a Convex and a Concave Wall at Low Injection Angles[J]. Journal of Turbomachinery， 1997， 119(3): 574-579.
[10] Qin Y， Ren J， Jiang H. Effects of Streamwise Pressure Gradient and Convex Curvature on Film Cooling Effectiveness[R]. ASME GT2014-25808.
[11] 刘聪，朱惠人，付仲议，等. 涡轮动叶压/吸力面气膜孔冷却特性实验研究[J]. 推进技术， 2016， 37(3):511-519.
[12] 付仲议，朱惠人，刘聪，等. 涡轮导叶压力面簸箕形气膜孔冷却特性实验研究[J]. 推进技术， 2016， 37(12): 2303-2311.
[13] Ekkad S V， Han J C， Du H. Detailed Film Cooling Measurements on a Cylindrical Leading Edge Model: Effect of Free-Stream Turbulence and Coolant Density[J]. Journal of Turbomachinery， 1997， 120(4): 799-807.
[14] Liu K， Yang S F， Han J C. Influence of Coolant Density on Turbine Blade Film-Cooling with Axial and Compound Shaped Holes[J]. Journal of Heat Transfer， 2012， 136(4).
[15] 李丽，彭晓峰，王补宣. 密度差和速度比对单排孔气膜冷却效率的影响[J]. 航空动力学报， 2007， 22(9): 1430-1434.
[16] 李冰，朱惠人，许都纯，等. 密度比对涡轮叶片表面气膜冷却换热系数的影响[J]. 航空学报， 2007， 28(4): 801-805.
[17] 李佳，任静，蒋洪德. 密度比和吹风比对透平静叶气膜冷却的影响[J]. 工程热物理学报， 2011， 32(8): 1295-1298.
[18] Ireland P T， Jones T V. Liquid Crystal Measurements of Heat Transfer and Surface Shear Stress[J]. Measurement Science and Technology， 2000， 11(7).
[19] Bai J T， Zhu H R， Liu C L. Film Cooling Characteristic of Double-Fan-Shaped Film Cooling Holes[R]. ASME GT2009-59318.
[20] Forder A， Thew M， Harrison D. A Numerical Investigation of Solid Particle Erosion Experienced Within Oilfield Control Valves[J]. Wear， 1998， 216(2): 184-193.
[21] Wang H P， Olson S J， Goldstein R J， et al. Flow Visualization in a Linear Turbine Cascade of High Performance Turbine Blades[J]. ASME Journal of Turbomachinery， 1997， 119(1): 1-8.

高主流湍流度下密度比对涡轮导叶全气膜冷却特性的影响

Effects of Density Ratio on Full Film Cooling Characteristics of Turbine Guide Vane with High Mainstream Turbulence

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 0

编辑推荐

Metrics

本文评价