改性双基推进剂断裂能下限研究

推进技术 ›› 2016, Vol. 37 ›› Issue (9): 1774-1779.

改性双基推进剂断裂能下限研究

郑健,赵超,周长省,许进升,陈雄

南京理工大学机械工程学院，江苏南京 210094,南京理工大学机械工程学院，江苏南京 210094,南京理工大学机械工程学院，江苏南京 210094,南京理工大学机械工程学院，江苏南京 210094,南京理工大学机械工程学院，江苏南京 210094

发布日期:2021-08-15
作者简介:郑健，男，博士，讲师，研究领域为固体火箭发动机总体技术。
基金资助:
总装重点预研项目(ZJ20101019)；江苏省自然科学青年基金(BK20140772)。

Research on Lower Limitation of Modified Double-Base

School of Mechanical Engineering，Nanjing University of Science and Technology，Nanjing 210094，China,School of Mechanical Engineering，Nanjing University of Science and Technology，Nanjing 210094，China,School of Mechanical Engineering，Nanjing University of Science and Technology，Nanjing 210094，China,School of Mechanical Engineering，Nanjing University of Science and Technology，Nanjing 210094，China and School of Mechanical Engineering，Nanjing University of Science and Technology，Nanjing 210094，China

Published:2021-08-15

摘要/Abstract

摘要： 为获得改性双基推进剂断裂能下限值，使用标准哑铃型试件、紧密拉伸试件和双边切口试件进行了不同拉伸速率下的单轴拉伸实验。实验结果表明:力与位移之间的关系可以反映三种试件失效形式的不同，失效形式决定了推进剂断裂能下限的获取方法。断裂能密度随拉伸速率的增大呈现出先急速上升后缓慢上升最终趋于稳定的过程。紧密拉伸试件和双边切口试件的断裂能密度明显低于标准哑铃型试件；当拉伸速率<200mm/min时，紧密拉伸试件的断裂能密度小于双边切口试件，随着拉伸速率的增大，两者的差距越来越小，可将紧密拉伸试件的断裂能密度作为改性双基推进剂断裂能下限；当拉伸速率>200mm/min时，紧密拉伸试件和双边切口试件的断裂能密度几乎相等，两种试件获得的断裂能密度均可作为改性双基推进剂断裂能下限。

关键词: 改性双基推进剂；断裂能密度；断裂能下限；获取方法

Abstract: To get lower limitation of modified double-base propellant’s fracture energy，a series of uniaxial tensile experiments under different tensile rates were conducted with standard dumbbell specimen(SDS)，compact tension specimen(CTS) and double edge notched specimen (DENS). The experiment results show that the relationship between force and displacement reflects different failure modes of three kinds of specimens，and the failure modes determine the way to get lower limitation of modified double-base propellant’s fracture energy. Fracture energy density rises sharply at first and then rises slowly and tends to a stable value along with the increase of tensile rates. The fracture energy density of CTS and DENS is lower than that of SDS significantly. When the tensile rate is less than 200 mm/min，CTS’s fracture energy density is lower than that of DENS，and the gap reduces with the increase of tensile rates，thus，the fracture energy density of CTS can be used as the lower limitation of modified double-base propellant’s fracture energy. When the tensile rate is greater than 200 mm/min，CTS and DENS have almost equal fracture energy density，so the fracture energy density of anyone of these two specimens can be regard as the lower limitation of modified double-base propellant’s fracture energy.

Key words: Modified double-base propellant；Fracture energy density；Lower limitation of fracture energy；Acquisition method

郑健,赵超,周长省,许进升,陈雄. 改性双基推进剂断裂能下限研究[J]. 推进技术, 2016, 37(9): 1774-1779.

ZHENG Jian,ZHAO Chao,ZHOU Chang-sheng,XU Jin-sheng,CHEN Xiong. Research on Lower Limitation of Modified Double-Base[J]. Journal of Propulsion Technology, 2016, 37(9): 1774-1779.

参考文献

[1] 孟红磊, 赵秀超, 鞠玉涛, 等. 基于累积损伤的双基推进剂强度准则及实验[J]. 推进技术, 2011, 32(1): 109-112. (MENG Hong-lei, ZHAO Xiu-chao, JU Yu-tao, et al. Strength Criterion Based on Accumulative Damage for Double-Base Propellant and Experiment[J].Journal of Propulsion Technology, 2011, 32(1): 109-112.)
[2] 孟红磊, 鞠玉涛, 周长省, 等. 改性双基推进剂损伤破坏研究[J]. 弹道学报, 2011, 23(2): 79-82.
[3] 汪文强, 郑健, 陈雄, 等. 基于扩展有限元的改性双基推进剂的开裂过程模拟研究[J]. 推进技术, 2015, 36(1): 149-154. (WANG Wen-qiang, ZHENG Jian, CHEN Xiong, et al. Numerical Simulation of Crack Propagation in CMDB Propellant Based on Extended Finite Element Method[J]. Journal of Propulsion Technology, 2015, 36(1): 149-154.)
[4] 郑健, 汪文强, 陈雄, 等. 基于微观结构分析的CMDB推进剂动态断裂韧性加载率敏感性研究[J]. 推进技术, 2015, 36(6): 940-946. (ZHENG Jian, WANG Wen-qiang, CHEN Xiong, et al. Effects of Loading Rate and Microstructure on Dynamic Fracture Toughness of CMDB Propellant[J]. Journal of Propulsion Technology, 2015, 36(6): 940-946.)
[5] 赵艳华, 聂玉强, 徐世烺. 混凝土断裂能的边界效应确定法[J]. 工程力学, 2007, 24(1): 56-61.
[6] 杨松森, 徐菁, 赵铁军. 混凝土断裂能测试方法研究[J]. 实验力学, 2009, 24(4): 327-333.
[7] Moukheiber E, Bas C, Flandin L. Understanding the Formation of Pinholes in PFSA Membranes with the Essential Work of Fracture[J]. International Journal of Hydrogen Energy, 2014, 39(6): 2717-2723.
[8] Arencon D, Antunes M, Martinez A B, et al. Study of the Fracture Behavior of Flexible Polypropylene Foams Using the Essential Work of Fracture[J]. Polymer Testing, 2012, 31(2): 217-225.
[9] Martinez A B, Gamez-Perez J, Sanchez-Soto M, et al. The Essential Work of Fracture Method-Analyzing the Post-Yielding Fracture Mechanics of Polymers[J]. Polymer Testing, 2009, 16(8): 2604-2617.
[10] Fabiano Moreno Peres, Jose Ricardo Tarpani, Claudio Geraldo Schon. An Assessment of Essential Work of Fracture Testing Method Applied to Medium Density Polyethylene (MDPE)[J]. Engineering Fracture Mechanics, 2013, 105(6): 136-151.
[11] Arakawa K, Mada T. Measuring Fracture Energy in a Brittle Polymeric Material: Application of a High-Speed Optical Extensometer[J]. Experimental Mechanics, 2007, 47(2): 211-216.
[12] Arakawa K, Mada T. Measuring Fracture Energy in a Brittle Polymeric Material[J]. Experimental Mechanics, 2006, 46(3): 347-353.
[13] Arakawa K, Mada T, Todo M, et al. Impact Tensile Fracture Testing of a Brittle Polymer[J]. Polymer Testing, 2006, 25(8): 1095-1100.
[14] Arakawa K, Masaru Kato, Toshio Mada. Tensile Fracture Testing and Energy Evaluation of a Light-Cured Composite Resin[J]. Polymer Testing, 2010, 29(1): 1-6.
[15] 常武军, 鞠玉涛, 王蓬勃. HTPB推进剂脱湿与力学性能的相关性研究[J]. 兵工学报, 2012, 33(3): 261-266.
[16] Chen Z T, Worswick M J, Cinotti N, et al. A Linked FEM-Damage Percolation Model of Aluminum Alloy Sheet Forming[J]. International Journal of Plasticity, 2003, 19(12): 2099-2120.(编辑:梅瑛)　　　　　　　　　　　　　*　收稿日期:2015-04-16；修订日期:2015-07-27。基金项目:总装重点预研项目(ZJ20101019)；江苏省自然科学青年基金(BK20140772)。作者简介:郑健,男,博士,讲师,研究领域为固体火箭发动机总体技术。E-mail: zhengjian@njust.edu.cn