涡轮叶片凹槽状叶顶非定常流动传热特性的数值研究

推进技术 ›› 2017, Vol. 38 ›› Issue (3): 551-558.

涡轮叶片凹槽状叶顶非定常流动传热特性的数值研究

杜昆¹,李军^1,2

西安交通大学能源与动力工程学院，陕西西安 710049,西安交通大学能源与动力工程学院，陕西西安 710049; 先进航空发动机协同创新中心，北京 100191

发布日期:2021-08-15
作者简介:杜昆，男，博士生，研究领域为气动热力学与流热耦合分析。
基金资助:
国家自然科学基金(51376144)。

Numerical Investigations on Unsteady Leakage Flow and Heat Transfer Characteristics of Turbine Blade with Squealer Tip

School of Energy & Power Engineering，Xi’an Jiaotong University，Xi’an 710049，China and School of Energy & Power Engineering，Xi’an Jiaotong University，Xi’an 710049，China; Collaborative Innovation Center of Advanced Aero-Engine，Beijing 100191，China

Published:2021-08-15

摘要/Abstract

摘要： 为了研究涡轮叶片凹槽状叶顶的非定常流动传热特性，以GE-E3第一级静叶和动叶为研究对象，采用ANSYS-CFX数值求解三维Reynolds-Averaged Navier-Stokes(RANS)和标准[k-ω]紊流模型。数值预测的叶顶换热系数分布与实验数据吻合良好，从而验证了数值方法的可靠性。数值计算结果表明:静叶尾迹对动叶顶部的流动和换热特性影响显著。压力面侧前缘区域和吸力面中间位置的流场受动静干涉影响显著。叶顶表面的换热系数脉动主要出现在靠近前缘的凹槽底部表面和再附着线附近及吸力面侧肩壁。靠近动叶尾缘区域的换热系数脉动同时受动静干涉作用和下游流场的影响。定常计算得到的换热系数在前缘冲击区和分离线附近高于非定常时均值，在压力面侧肩壁附近小于非定常时均值。定常计算得到的平均换热系数要高出非定常计算结果3.5%。

关键词: 涡轮叶片；凹槽叶顶；非定常泄漏流；传热特性；数值模拟

Abstract: In order to investigate the unsteady heat transfer characteristics of the turbine blade with squealer tip，the first stage of GE-E3 turbine was implemented and the numerical simulations were conducted using three-dimensional Reynolds-Averaged Navier-Stokes(RANS) and standard [k-ω] turbulent model based on the CFD software ANSYS-CFX. The numerical results agree well with the experimental data on the experimental blade tip. The accuracy of the utilized numerical approach has been validated. The numerical results show that the tip flow structure and the heat transfer performance of blade tip are significantly affected by the wake flow. The flow field in the regions near the pressure side leading edge and the middle chord suction side is greatly influenced by the rotor-stator interaction. The fluctuations of the heat transfer coefficients are observed near the leading edge impingement region，the reattachment line and the suction side squealer rim. The heat transfer coefficients on the blade tip near the trailing edge are affected by the downstream flow field and the rotor-stator interaction. The level of heat transfer obtained from the steady simulation is enhanced near the reattachment line and the impingement region，however which is reduced near the pressure side squealer rim by comparison with the time-averaged results. The average heat transfer coefficient of the blade tip surface obtained by steady result is 3.5% higher than the unsteady time-averaged result.

Key words: Turbine blade；Squealer tip；Unsteady leakage flow；Heat transfer characteristics；Numerical simulation

杜昆,李军. 涡轮叶片凹槽状叶顶非定常流动传热特性的数值研究[J]. 推进技术, 2017, 38(3): 551-558.

DU Kun¹,LI Jun^1,2. Numerical Investigations on Unsteady Leakage Flow and Heat Transfer Characteristics of Turbine Blade with Squealer Tip[J]. Journal of Propulsion Technology, 2017, 38(3): 551-558.

参考文献

[1] Bunker R S. Axial Turbine Blade Tips: Function, Design, and Durability[J]. Journal of Propulsion and Power, 2006, 22(2): 271-285.
[2] 韩介勤. 燃气轮机冷却和传热技术[M]. 西安:西安交通大学出版社, 2005.
[3] Kwak J S, Han J C. Heat Transfer Coefficient on a Gas Turbine Blade Tip and Near Tip Regions[R]. AIAA 2002-3012.
[4] Saxena V, Nasir H, Ekkad S V. Effect of Blade Tip Geometry on Tip Flow and Heat Transfer for a Blade in a Low-Speed Cascade[J]. ASME Journal of Turbomachinery, 2004, 126(1): 130-138.
[5] Nasir H, Ekkad S V,Kontrovitz D M, et al. Effect of Tip Gap and Squealer Geometry on Detailed Heat Transfer Measurements Over a High Pressure Turbine Rotor Blade Tip[J]. ASME Journal of Turbomachinery, 2004, 126(2): 221-228.
[6] 杨佃亮, 丰镇平, 余小兵. 凹槽叶顶非定常间隙泄漏流动和传热的数值研究[J]. 工程热物理学报, 2009, 30(4): 591-594.
[7] 虞跨海, 杨茜, 岳珠峰. 高压涡轮冷却冷片叶顶结构气动与传热[J]. 推进技术, 2012, 33(2): 174-178. (YU Kua-hai, YANG Xi, YUE Zhu-feng. Aerodynamic and Heat Transfer of Cooling Blade Tips for High Pressure Turbine[J]. Journal of Propulsion Technology, 2012, 33(2): 174-178.)
[8] 贾惟, 刘火星. 涡轮叶栅叶冠泄漏流动数值研究[J]. 推进技术, 2013, 34(3): 316-325. (JIA Wei, LIU Huo-xing. Numerical Investigation on Shroud Leakage Flow in Turbine Cascade[J]. Journal of Propulsion Technology, 2013, 34(3): 316-325.)
[9] Zhou C, Hodson H, Tibbott I, et al. The Aerothermal Performance of a Cooled Winglet Tip in a High Pressure Turbine Cascade[J]. ASME Journal of Turbomachinery, 2013, 135(5): 1-10.
[10] 杜昆, 宋立明, 李军. 凹槽状叶顶涡轮叶片传热特性的数值研究[J]. 推进技术, 2014, 35(5): 618-623. (DU Kun, SONG Li-ming, LI Jun. Numerical Investigations on Heat Transfer Characteristics of Turbine Blade with Squealer Tip[J]. Journal of Propulsion Technology, 2014, 35(5): 618-623.)
[11] Arisi A, Xue S, Ng W F, et al. Numerical Investigation of Aerothermal Characteristics of the Blade Tip and Near-Tip Regions of a Transonic Turbine Blade[J]. ASME Journal of Turbomachinery, 2015, 137(9): 1-12.
[12] 朱惠人, 张丽, 周永成, 等. 非定常尾迹对涡轮叶片换热影响的数值模拟[J]. 推进技术, 1999, 20(4): 53-56. (ZHU Hui-ren, ZHANG Li, ZHOU Yong-cheng. Numerical Simulation of Influence of Unsteady Wake on Heat Transfer of Turbine Blade [J]. Journal of Propulsion Technology, 1999, 20(4): 53-56.)
[13] Ameri A A, Rigby D L, Steinthorsson E, et al. Unsteady Analysis of Blade and Tip heat Transfer as Influenced by the Upstream Momentum and Thermal Wakes [J]. ASME Journal of Turbomachinery, 2010, 132(10): 1-7.
[14] Mischo B, Burdet A, Abhari R S. Influence of Stator-Rotor Interaction on the Aerothermal Performance of Recess Blade Tips [J]. ASME Journal of Turbomachinery, 2011, 133(1): 1-11.
[15] Rahman Md H, Kim S I,Hassan I. Effects of Inlet Temperature Uniformity and Nonuniformity on the Tip Leakage Flow and Rotor Blade Tip and Casing Heat Transfer Characteristics[J]. ASME Journal of Turbomachinery, 2012, 134(3): 1-10.
[16] Liu Z F, Liu Z, Feng Z P. Unsteady Analysis on the Effects of Tip Clearance Height on Hot Streak Migration Across Rotor Blade Tip Clearance[J]. ASME Journal of Engineering for Gas Turbines and Power, 2014, 136(8): 1-11.　　　　　　　　　　　　　　收稿日期:2015-09-15；修订日期:2016-01-06。基金项目:国家自然科学基金(51376144)。作者简介:杜昆,男,博士生,研究领域为气动热力学与流热耦合分析。E-mail: dk703301@stu.xjtu.edu.cn(编辑:史亚红)