单液滴羽状/液膜稀释破碎特性研究

推进技术 ›› 2017, Vol. 38 ›› Issue (4): 885-895.

单液滴羽状/液膜稀释破碎特性研究

金仁瀚¹,刘勇²,王锁芳²

盐城工学院汽车工程学院，江苏盐城 224001,南京航空航天大学能源与动力学院江苏省航空动力系统重点实验室，江苏南京 210016,南京航空航天大学能源与动力学院江苏省航空动力系统重点实验室，江苏南京 210016

发布日期:2021-08-15
作者简介:金仁瀚，男，博士生，研究领域为航空发动机燃烧室燃油雾化。

Experimental Investigations of Breakup Characteristic of Single Droplet in Plume/Sheet-Thinning Breakup Regime in Airflow

College of Automotive Engineering，Yancheng Institute of Technology，Yancheng 224001，China,Nanjing University of Aeronautics and Astronautics，Jiangsu Province Key Laboratory of Aerospace Power System，Nanjing 210016，China and Nanjing University of Aeronautics and Astronautics，Jiangsu Province Key Laboratory of Aerospace Power System，Nanjing 210016，China

Published:2021-08-15

摘要/Abstract

摘要： 为了获得气流中单液滴羽状/液膜稀释破碎特性，采用高速摄像机对液滴变形、破碎过程进行了捕获。实验结果表明:液滴的变形时间小于其破碎时间，且都随气动力增加呈负增长的变化趋势，其变化梯度、相同气动力下特征时间也都随液滴初始直径的增加而有所增加；液滴破碎区域面积随气动力增加呈先增加后减小再增加的变化趋势，且随液滴初始直径增加，液滴破碎区域面积也随之增加；破碎区域中子液滴质量百分数随气动力增加而增加，且随液滴初始直径增加而减小，其值变化的范围为0.48～0.66；液滴的破碎程度随气动力、液滴初始直径的增加而增加；破碎区域中子液滴细度与液滴初始细度的比值在0.18～0.23之间变化；在羽状/液膜稀释破碎阶段，多元线性回归理论可以用于建立子液滴数目、SMD的数学模型。

关键词: 液滴；雾化；热气流；喷雾；高速摄像机

Abstract: In order to obtain characteristic of single droplet in the plume/sheet-thinning breakup regime in airflow，the high-speed cameras were applied to measure single droplet deformation and breakage. Experimental results show that the character time of droplet breakup had a negative relationship with the aerodynamics，while its value and change gradient were both positively associated with the original droplet diameter，and the deformation time was less than the broken time. The area of droplet breakup increased but then changed to decrease and increased again with the increase of aerodynamics，and the area of droplet breakup increased as the increase of original diameters. The percentage of sub-droplet mass increased with the increase of aerodynamics，but it decreased as the increase of original diameters，and its value changed between 0.48～0.66. The level of droplet breakup was significantly improved as the increase of droplet original diameter and the aerodynamics. The ratio of sub-droplet fineness and initial droplet fineness varied between 0.18～0.23. The multivariate linear regression analysis method could be used to establish the mathematical model of the number and sauter mean diameter (SMD) of sub-droplet，in the plume/sheet-thinning breakup regime.

Key words: Droplet；Atomization；Heated air flow；Sprays；High-speed cameras

金仁瀚,刘勇,王锁芳. 单液滴羽状/液膜稀释破碎特性研究[J]. 推进技术, 2017, 38(4): 885-895.

JIN Ren-han¹,LIU Yong²,WANG Suo-fang². Experimental Investigations of Breakup Characteristic of Single Droplet in Plume/Sheet-Thinning Breakup Regime in Airflow[J]. Journal of Propulsion Technology, 2017, 38(4): 885-895.

参考文献

[1] Guildenbecher D R, Lopez-Rivera C, Sojka P E. Secondary Atomization[J]. Experiments in Fluids, 2009, 46(3): 371-402.
[2] Pilch M, Erdman C A. Use of Breakup Time Data and Velocity History Data to Predict the Maximum Size of Stable Fragments for Acceleration-Induced Breakup of a Liquid Drop[J]. International Journal of Multiphase Flow, 1987, 13(6): 741-757.
[3] Hsiang L P, Faeth G M. Near-Limit Drop Deformation and Secondary Breakup[J]. International Journal of Multiphase Flow, 1992, 18(5): 635-652.
[4] Simmons H C. The Correlation of Drop-Size Distributions in Fuel Nozzle Sprays, Part I: The Drop-Size/Volume-Fraction Distribution[J]. Journal of Engineering for Gas Turbines & Power, 1976, 99(3): 309-314.
[5] Simmons H C. The Correlation of Drop-Size Distributions in Fuel Nozzle Sprays, Part II:The Drop-Size/Number Distribution[J]. American Society of Mechanical Engineers, 1976, 99(3): 315-319.
[6] Hsiang LP, Faeth GM. Drop Properties after Secondary Breakup[J]. International Journal of Multiphase Flow, 1993, 19(5): 721-735.
[7] Chou W H, Faeth G M. Temporal Properties of Secondary Drop Breakup in the Bag Breakup Regime[J]. International Journal of Multiphase Flow, 1998, 24(6): 889-912.
[8] Chou W H, Hsiang L P, Faeth G M. Temporal Properties of Drop Breakup in the Shear Breakup Regime[J].International Journal of Multiphase Flow, 1997, 23(4):651-669.
[9] Wert K L. A Rationally-Based Correlation of Mean Fragment Size for Drop Secondary Breakup[J]. International Journal of Multiphase Flow, 1995, 21(6): 1063-1071.
[10] Cousin J, Yoon S J, Dumouchel C. Coupling of Classical linear Theory and Maximum Entropy Formalism for Prediction of Drop Size Distribution in Sprays: Application to Pressure-Swirl Atomizers[J]. Atomization Spray, 1996, 6(5): 601-622.
[11] Dumouchel C, Boyaval S. Use of the Maximum Entropy Formalism to Determine Drop Size Characteristics[J].Particle and Particle Systems Characterization, 1999, 16(4): 177-184.
[12] Li X, Li M, Fu H. Modeling the Initial Droplet Size Distribution in Sprays Based on the Maximization of Entropy Generation[J]. Atomization Spray, 2005, 15(3): 295-321.
[13] O’Rourke P J, Amsden A A. The TAB Method for Numerical Calculation of Spray Droplet Breakup[D]. Society of Automotive Engineers Paper, 1987, No 872089.
[14] Hwang S S, Liu Z, Reitz R D. Breakup Mechanisms and Drag Coefficients of High-Speed Vaporizing Liquid Drops[J]. Atomization and Sprays, 1996, 6(3): 353-376.
[15] Park S W, Lee C S. Investigation of Atomization and Evaporation Characteristics of High-Pressure Injection Diesel Spray Using Kelvin-Helmholtz Instability/Droplet Deformation and Break-Up Competition Model[J].Proceedings of the Institution of Mechanical Engineers,Part D: Journal of Automobile Engineering, 2004, 218(7): 767-777.
[16] 冯守义, 牛志刚, 费立群, 等,高密度烃燃料雾化特性实验[J]. 推进技术, 2011, 32(4): 512-519. (FENG Shou-yi, NIU Zhi-gang, FEI Li-qun, et al. Experiment on Atomization Characteristics of High Density Hydrocarbon[J]. Journal of Propulsion Technology, 2011, 32(4): 512-519.)
[17] 金仁瀚, 张铮, 刘勇, 等. 横向加热气流中直射式喷嘴侧喷雾化特性研究[J]. 推进技术, 2013, 34(5): 658-663. (JIN Ren-han, ZHANG Zheng, LIU Yong, et al. Experimental Study on Atomization Characteristics of Simple Nozzle in Heating Cross Flow [J]. Journal of Propulsion Technology, 2013, 34(5): 658-663.)
[18] Sung Wook part, Sayop, Chang Sik Lee. Effect of Mixing Ratio of Biodiesel on Breakup Mechanisms of Monodispersed Droplets[J]. Energy and Fuels, 2006, 20(4): 1709-1715.
[19] 杨淑莹. VC++图像处理程序设计[M]. 清华大学出版社, 2005.
[20] 金仁瀚, 刘勇, 朱冬清, 等. 连续均匀气流中单液滴破碎特性实验[J]. 推进技术, 2016, 37(2): 273-280. (JIN Ren-han, LIU Yong, ZHU Dong-qing, et al. Experimental Investigations of Breakup Characteristic of Single Droplet in the Continuous Uniform Airflow[J]. Journal of Propulsion Technology, 2016, 37(2): 273-280.)
[21] 金仁瀚, 刘勇, 朱冬清, 等. 初始直径对单液滴破碎特殊影响的实验研究[J]. 航空动力学报, 2015, 30(10): 2401-2409.
[22] 金仁瀚, 刘勇, 王锁芳, 等. 横向热气流中单液滴剪切破碎特性研究[J]. 推进技术, 2016, 37(10).(JIN Ren-han, LIU Yong, WANG Suo-fang, et al. Experimental Investigations of Breakup Characteristic of Single Droplet in the Sheet-Thinning Breakup Regime in Heating Cross Airflow[J]. Journal of Propulsion Technology, 2016, 37(10).)
[23] 贾俊平, 何晓群, 金勇进. 统计学(第五版) [M]. 中国人民大学出版社, 2014: 265-273.
[24] Allen D M. Mean Square Error of Prediction as a Criterion for Selecting Variables[J]. Technometrics, 1971, 13(3): 469-475.
[25] 高惠璇. 统计计算[M]. 北京:北京大学出版社, 2005.　　　　　　　　　　　　　*　收稿日期:2015-11-13；修订日期:2015-12-22。作者简介:金仁瀚,男,博士生,研究领域为航空发动机燃烧室燃油雾化。E-mail: kingrenhan@163.com(编辑:田佳莹)