一款国外喷水推进器的三维反问题改进设计

推进技术 ›› 2017, Vol. 38 ›› Issue (12): 2699-2705.

一款国外喷水推进器的三维反问题改进设计

张明宇,林瑞霖,王永生,靳栓宝

海军工程大学动力工程学院，湖北武汉 430033,海军工程大学动力工程学院，湖北武汉 430033,海军工程大学动力工程学院，湖北武汉 430033,海军工程大学动力工程学院，湖北武汉 430033

发布日期:2021-08-15
作者简介:张明宇，男，博士生，研究领域为喷水推进器设计及优化。
基金资助:
国家自然科学基金(51309229)。

Revised Design of a Foreign Waterjet Based on 3-D Inverse Method

College of Marine Power Engineering，Naval University of Engineering，Wuhan 430033，China,College of Marine Power Engineering，Naval University of Engineering，Wuhan 430033，China,College of Marine Power Engineering，Naval University of Engineering，Wuhan 430033，China and College of Marine Power Engineering，Naval University of Engineering，Wuhan 430033，China

Published:2021-08-15

摘要/Abstract

摘要： 某厂家购置的国外喷水推进器装艇后与主机不匹配，不能完全消耗主机功率，导致艇航速较低。针对这一现象，在保持推进器转子叶片数、导叶数和推进器主体尺寸不变的前提下，采用三维反问题方法对叶轮和导叶进行了增载设计。研究采用CFD数值模拟方法对两推进器进行了平底船数值求解，结果表明:原推进器计算结果与自航试验吻合较好，验证了CFD数值模拟的可信性；新设计推进器解决了原推进器不能充分利用主机功率的缺陷而产生更大的推力，使预报航速从9.5kn提高到12kn，喷泵效率提高2%，喷口射流轴向能量分量提高8%。

关键词: 喷水推进器；叶轮；导叶；三维反问题设计；CFD数值模拟

Abstract: A waterjet bought from abroad could not make the best of the engine power which caused the boat a lower speed. The study improved the waterjet design for this phenomenon through increasing load capacity of the rotor and stator based on 3-D inverse method， during which both the blade number of rotor， stator and the main dimensions of the propulsor were kept unchanged. Numerical simulation of two waterjets mounted on the same punt was implemented and results showed that calculated results of the original waterjet agreed well with the experiment data， which verified the credibility of numerical simulation. The newly-designed waterjet could make the best of the engine power and generated a greater thrust which increased the speed from 9.5kn to 12kn， efficiency of the waterjet pump increased by 2% and jets axial energy component of nozzle increased by 8%.

Key words: Waterjet；Rotor；Stator；3-D inverse design；CFD numerical simulation

张明宇,林瑞霖,王永生,靳栓宝. 一款国外喷水推进器的三维反问题改进设计[J]. 推进技术, 2017, 38(12): 2699-2705.

ZHANG Ming-yu,LIN Rui-lin,WANG Yong-sheng,JIN Shuan-bao. Revised Design of a Foreign Waterjet Based on 3-D Inverse Method[J]. Journal of Propulsion Technology, 2017, 38(12): 2699-2705.

参考文献

[1] Wessel J. Waterjet Propulsion for a 3500 Ton Corvette from BLOHM+VOSS[C]. London: RINA, International Conference on Waterjet Propulsion IV, The Royal Institution of Naval Architects, 2004.
[2] Lavis D R, Forstell B G, Purnel J G. Compact Waterjets for High-Speed Ships[J]. Ships and Offshore Structures, 2007, 2(2):115-125.
[3] Purnell J. Waterjet Self-Propulsion Model Test for Application to a High-Speed Sealift Ship[R]. Severna Park: CDI Marine Company, 2007.
[4] Bonaiuti D, Zangeneh M, Aartojarvi R, et al. Parametric Design of a Waterjet Pump by Means of Inverse Design, CFD Calculations and Experimental Analyses[J]. ASME Journal of Fluids Engineering, 2010, 132: 1-15.
[5] 靳栓宝, 王永生, 丁江明, 等. 混流式喷水推进泵三元设计及数值试验[J]. 哈尔滨工程大学学报, 2012, 33(10):1223-1227.
[6] 靳栓宝, 沈洋, 王东, 等. 基于数值试验及实船试航的喷水推进器改型设计[J]. 船舶力学, 2015, 19(11): 1312-1317.
[7] 刘昭威, 吴虎, 唐晓毅. 跨声速轴流压气机转子反问题优化方法[J]. 推进技术, 2015, 36(9): 1309-1316. (LIU Zhao-wei, WU-Hu, TANG Xiao-yi. Optimization of Transonic Axial Compressor Rotor Using Improved Inverse Method[J]. Journal of Propulsion Technology, 2015, 36(9): 1309-1316.)
[8] 彭云龙, 王永生, 靳栓宝. 轴流式喷水推进泵的三元设计[J]. 中南大学学报(自然科学版), 2014, 45(6):1812-1818.
[9] 曹玉良, 王永生, 靳栓宝. 喷水推进轴流泵三元水力设计[J]. 交通运输工程学报, 2015, 15(2): 42-49.
[10] 常书平, 石岩峰, 周晨, 等. 出口环量分布对混流泵性能的影响[J]. 农业机械学报, 2014, 45(1): 89-93.
[11] 肖若富, 陶然, 王维维, 等. 混流泵叶轮反问题设计与水力性能优化[J]. 农业机械学报, 2014, 45(9): 84-88.
[12] 周凡贞, 王世勇, 丁晓娟, 等. 涡轮高载荷叶片设计及级三维流场数值分析[J]. 推进技术, 2004, 25(1):62-65. (ZHOU Fan-zhen, WANG Shi-yong, DING Xiao-juan, et al. Design and 3-D Numerical Analysis of Highly Loaded Turbine Rotor Blade[J]. Journal of Propulsion Technology, 2004, 25(1): 62-65.)
[13] 王福军. 计算流体动力学分析—CFD软件原理与应用[M]. 北京:清华大学出版社, 2004.
[14] 张明宇, 王永生, 靳栓宝, 等. 喷水推进泵脉动特性数值计算及分析[J]. 西安交通大学学报, 2014, 48(11): 51-57.
[15] 罗兴琦. 混流式水轮机转轮的全三维反问题计算与优化[D]. 北京:清华大学水利系, 1995.
[16] 关醒凡. 现代泵技术手册[M]. 北京:宇航出版社, 1995: 326-332.
[17] Goto A, Nohmi M, Sakurai T, et al. Hydrodynamic Design System for Pumps Based on 3-D CAD, CFD and Inverse Design Method[J]. ASME Journal of Fluids Engineering, 2002, 124(2): 329-335.
[18] 邴浩, 曹树良, 陆力. 混流泵叶轮设计关键参数分析[J]. 水力发电学报, 2013, 32(3): 229-233.　　　　　　　　　　　　　*　收稿日期:2016-09-05；修订日期:2016-11-01。基金项目:国家自然科学基金(51309229)。作者简介:张明宇,男,博士生,研究领域为喷水推进器设计及优化。E-mail: yijianmingyu@163.com(编辑:史亚红)