致密发散孔冷却环形折流甩油盘燃烧室设计研究

推进技术 ›› 2017, Vol. 38 ›› Issue (12): 2788-2796.

致密发散孔冷却环形折流甩油盘燃烧室设计研究

何悟^1,2,郭志辉¹,赵学成²,邵伏永²,蒋雪辉²,吴静²

北京航空航天大学能源与动力工程学院，北京 100191; 北京动力机械研究所，北京 100074,北京航空航天大学能源与动力工程学院，北京 100191,北京动力机械研究所，北京 100074,北京动力机械研究所，北京 100074,北京动力机械研究所，北京 100074,北京动力机械研究所，北京 100074

发布日期:2021-08-15
作者简介:何悟，男，博士生，工程师，研究领域为涡轮发动机燃烧室设计和试验。

Design Investigation of Annular Combustor with Slinger and Compacted Effusion Cooling Holes

School of Energy and Power Engineering，Beihang University，Beijing 100191，China; Beijing Power Machinery Institute，Beijing 100074，China,School of Energy and Power Engineering，Beihang University，Beijing 100191，China,Beijing Power Machinery Institute，Beijing 100074，China,Beijing Power Machinery Institute，Beijing 100074，China,Beijing Power Machinery Institute，Beijing 100074，China and Beijing Power Machinery Institute，Beijing 100074，China

Published:2021-08-15

摘要/Abstract

摘要： 为了研究致密发散小孔冷却环形折流燃烧室的设计方法，根据火焰筒头部无冷却时的流场形态及期望引导的流场形态，对头部壁面发散小孔进行了两种对比性设计。为对比两种方案的优劣，对设计后的燃烧室进行了数值模拟。结果表明通过增加发散小孔，调节内外环射流孔的气量分配，可成功诱导出期望的多涡流场，且方案2的发散小孔冷却效果更佳。证明通过调整内外环发散小孔开孔数量来调节射流孔的射流穿透深度，并结合甩油盘油雾诱导理想的主燃区流场形成是可行的；采用孔倾角为钝角的发散小孔可更好地保护热负荷压力大的前几排火焰筒壁面；通过在高温区增大孔阵疏密度，把高温区处的发散小孔孔径由原先的0.68mm减小至0.3～0.55mm，可实现在不改变冷气流量的前提下，增强换热，降低壁面温度。

关键词: 甩油盘环形燃烧室；发散冷却孔；主燃区；流场；仿真

Abstract: In order to design annular combustor with slinger and compacted effusion cooling holes， two kinds of comparative methods on effusion cooling holes are conducted according to the flow field of flame tube without effusion cooling holes and the desirable multi-vortexes flow field. For comparing the effectiveness of these two methods， the combustion field of combustors has been simulated. The computational results indicate that adding the number of effusion holes to adjust the gas distribution of jet holes of outer and inner liner can induce the multi-vortexes flow fields， and the cooling effectiveness of method 2 is better. It shows that adjusting the number of holes to change the air penetration distance of jet holes and using the atomized fuel from slinger can induce the desirable flow field. The effusion cooling holes with obtuse angle to the mainstream can protect the first rows of flame tube with large heat load better. Increasing porosity of holes array and changing the diameter of holes from 0.68mm to 0.3～0.55mm can enhance heat transfer and reduce the wall temperature without changing cooling air mass flow.

Key words: Annular combustor with slinger；Effusion cooling holes；Primary combustion zone；Flow field；Simulation

何悟,郭志辉,赵学成,邵伏永,蒋雪辉,吴静. 致密发散孔冷却环形折流甩油盘燃烧室设计研究[J]. 推进技术, 2017, 38(12): 2788-2796.

HE Wu^1,2,GUO Zhi-hui¹,ZHAO Xue-cheng²,SHAO Fu-yong²,JIANG Xue-hui²,WU Jing². Design Investigation of Annular Combustor with Slinger and Compacted Effusion Cooling Holes[J]. Journal of Propulsion Technology, 2017, 38(12): 2788-2796.

参考文献

[1] 胡正义. 航空发动机设计手册(第9册):主燃烧室[M]. 北京:航空工业出版社, 2000.
[2] 曾川?, 王洪铭?, 单鹏, 等. 微涡喷发动机离心甩油盘环形折流燃烧室的设计与实验研究[J]. 航空动力学报, 2003, 18(2): 92-96.
[3] 宋双文, 蒋荣伟, 陈剑, 等. 离心甩油折流环形燃烧室的性能试验[J]. 航空动力学报, 2007, 22(9).
[4] Harris M M, Jones A C, Alexander E J. Miniature Turbojet Development at Hamiltion Sundstrand the TJ-50, TJ-120 and TJ-30 Turbojet[R]. AIAA 2003-6568.
[5] 陈晓丽, 蒋雪辉, 何悟, 等. 微小型甩油盘式燃烧室若干关键技术研究[J]. 推进技术, 2016, 37(2): 296-304. (CHEN Xiao-li, JIANG Xue-hui, HE Wu, et al. A Study on Key Technologies of Micro Combustor with a Slinger Injector[J]. Journal of Propulsion Technology, 2016, 37(2): 296-304.)
[6] 何悟, 张哲, 刘嘉垚, 等. 微型涡喷发动机燃烧室优化与试验研究[J]. 推进技术, 2016, 37(10): 1875-1881. (HE Wu, ZHANG Zhe, LIU Jia-yao, et al. The Optimization and Experimental Research of the Micro Turbojet Engine Combustor[J]. Journal of Propulsion Technology, 2016, 37(10): 1875-1881.)
[7] Gerendas M, Hoschler K, Schiling Th. Development and Modeling of Angled Effusion Cooling for the BR 715 Low Emission Staged Combustor Core Demonstrator[R].ADA-419282.
[8] Powel S F IV. On the Leading Edge: Combining Maturity and Advanced Technology on the F404 Turbofan Engine[J]. Journal of Engineering for Gas Turbines and Power, 1991, 113(1): 1-10.
[9] 方昌德. 世界航空发动机手册[M]. 北京:航空工业出版社, 1996.
[10] 李志强, 田涛, 陈钦. 多斜孔火焰筒壁冷却结构的数值模拟[J]. 北京航空航天大学学报, 2008, 34(10).
[11] 徐剑, 许全宏, 林宇震, 等. 火焰筒多斜孔冷却方式壁温梯度和冷却效率试验[J]. 航空动力学报, 2008, 23(3).
[12] Andrews G E, Alikhanizadeh M, Tehrani F B, et al. Small Diameter Film Cooling Holes: Influence of Hole Size and Pitch[J]. International Journal of Turbo and Jet Engines, 1988, 5(1-4): 61-72.
[13] Andrews G E, Khalifa I M, Asere A A, et al. Full Coverage Effusion Film Cooling with Inclined Holes[R]. ASME 1995-GT-274.
[14] Gustafsson K M B, Johansson T G. An Experimental Study of Surface Temperature Distribution on Effusion-Cooled Plates[J]. Journal of Engineering for Gas Turbines and Power, 2001, 123(2): 308-316.
[15] LinY L, Stephens M A, Shih S I- P. Computational of Leading-Edge Film Cooling with Injection Through Raws of Compound-Angle Holes[C]. Orlando: International Gas-Turbine & Aeroengine Congress & Exhibition, 1997.
[16] 赵文毓, 王力军. 逆向射流多斜孔气膜冷却的数值模拟[J]. 沈阳航空工业学院学报, 2007, 24(4).
[17] Mayle R E, Camarata F J. Multihole Cooling Film Effectiveness and Heat Transfer[J]. ASME Transactions Journal of Heat Transfer, 1975, 97(4): 534-538.
[18] Bazdidi T F, Andrews G E. Full Coverage Discrete Hole Film Cooling: Investigation of the Effect of Variable Density Ratio[J]. ASME Transactions Journal of Engineering for Gas Turbines and Power, 1994, 116(3): 587-596.
[19] 林宇震, 李彬, 宋波, 等. 不同倾斜角多斜孔壁冷却方式绝热温比研究 [J]. 航空学报, 1999, 20(3).
[20] Sellers J P Jr. Gaseous Film Cooling with Multiple Injection Stations[J]. AIAA Journal, 1963, 1(9): 2145-2156.
[21] 宋波, 林宇震, 刘高恩, 等. 不同排列方式多斜孔壁气膜冷却绝热温比研究[J]. 航空动力学报, 1999, 14(1): 91-94.
[22] 胡娅萍, 吉洪湖, 郑妹, 等. 孔排布方式对多斜孔壁火焰筒传热特性影响的数值研究[J]. 推进技术, 2013, 34(5). (HU Ya-ping, JI Hong-hu, ZHANG Mei, et al. Numerical Simulation of Effect of Hole Displacement on Heat Transfer Characteristics of an Effusion Cooled Flame Tube[J]. Journal of Propulsion Technology, 2013, 34(5).)
[23] 陈焱, 吉洪湖, 胡娅萍, 等. 致密微孔壁绝热冷却效果的研究[J]. 工程热物理学报, 2006, 27(2): 25-28.
[24] 胡娅萍, 吉洪湖. 孔阵排列疏密度对致密多孔壁冷却效果的影响[J]. 推进技术, 2005, 26(1): 28-33. (HU Ya-ping, JI Hong-hu. Effect of Porosity of Holes Array on Cooling Effectiveness of Effusion Cooling[J]. Journal of Propulsion Technology, 2005, 26(1): 28-33.)
[25] 刘常春, 吉洪湖, 杨芳芳, 等. 孔阵排列和偏转角对多斜孔壁火焰筒冷却效果的影响研究[J]. 推进技术, 2013, 34(10). (LIU Chang-chun, JI Hong-hu, YANG Fang-fang, et al. Numerical Study on Cooling Effects of Hole Arrangement and Deflected Angle of Inclined Multi-Hole on Annular Flame Tube[J]. Journal of Propulsion Technology, 2013, 34(10).)
[26] 曹俊, 杨卫华, 石蕊, 等. 弯曲段壁面冲击发散冷却效率的实验[J]. 推进技术. 2011, 32(4): 479-484. (CAO Jun, YANG Wei-hua, SHI Rui, et al. Film Cooling Effectiveness Experiment of Impingement Effusion Cooling in Curved Section[J]. Journal of Propulsion Technology, 2011, 32(4): 479-484.)
[27] 刁瑶朋, 王少波. 多斜孔冷却火焰筒燃烧性能试验研究[J]. 航空发动机, 2016, 42(1): 84-87.
[28] 杨卫华, 彭建勇, 曹俊, 等. 回流燃烧室复合冷却结构冷却效果研究[J]. 南京航空航天大学学报, 2012, 44(6): 769-774.
[29] 何悟, 郑洪涛, 蔡林, 等. 湍流燃烧模型在燃烧室数值计算中的对比分析[J]. 热科学与技术, 2011, 10(4): 360-365.　　　　　　　　　　　　　*　收稿日期:2016-07-08；修订日期:2016-10-25。作者简介:何悟,男,博士生,工程师,研究领域为涡轮发动机燃烧室设计和试验。E-mail: 714028720@qq.com(编辑:朱立影)