Experimental Study of Effects of Bolts Inside Multilayer Turbine Casing on Heat Transfer Characteristics

Journal of Propulsion Technology ›› 2017, Vol. 38 ›› Issue (7): 1441-1449.

Shanghai Civil Aviation College，Shanghai 200232，China; Nanjing University of Aeronautics and Astronautics，Jiangsu Province Key Laboratory of Aerospace Power System，Nanjing 210016，China,Nanjing University of Aeronautics and Astronautics，Jiangsu Province Key Laboratory of Aerospace Power System，Nanjing 210016，China,Nanjing University of Aeronautics and Astronautics，Jiangsu Province Key Laboratory of Aerospace Power System，Nanjing 210016，China,Department of Secondary Air System，Shenyang Engine Design and Research Institute，Aviation Industry Corporation of China，Shenyang 110015，China,Department of Secondary Air System，Shenyang Engine Design and Research Institute，Aviation Industry Corporation of China，Shenyang 110015，China and Department of Secondary Air System，Shenyang Engine Design and Research Institute，Aviation Industry Corporation of China，Shenyang 110015，China

Published:2021-08-15

多层涡轮机匣内螺栓对换热特性影响的试验研究

刘震雄^1,2,毛军逵²,江华²,李俊山³,沈毅³,陆海鹰³

上海民航职业技术学院，上海 200232; 南京航空航天大学能源与动力学院，江苏省航空动力系统重点实验室，江苏南京 210016,南京航空航天大学能源与动力学院，江苏省航空动力系统重点实验室，江苏南京 210016,南京航空航天大学能源与动力学院，江苏省航空动力系统重点实验室，江苏南京 210016,中国航空工业集团公司沈阳发动机设计研究所内流传热室，辽宁沈阳 110015,中国航空工业集团公司沈阳发动机设计研究所内流传热室，辽宁沈阳 110015,中国航空工业集团公司沈阳发动机设计研究所内流传热室，辽宁沈阳 110015

作者简介:刘震雄，男，博士生，讲师，研究领域为航空发动机传热、传质研究以及稳定性。

Abstract

Abstract: According to multilayer casing of high pressure turbine with active clearance control system，experiments were conducted to investigate the effects of embedded bolts on heat transfer characteristics，which inside the oblique?impact high rib structure of the turbine casing. In experiments，the average Reynolds number [Re]([2543~7121])，the ratio of bolt diameter to jet holes diameter [Dd](2.67，4.13，5.33) and the spacing ratio [Sd] (23.2，30.7，45.2) were changed to investigate the local and average heat transfer coefficient [Nu](Nusselt number). The empirical formulas of average heat transfer with [Dd] and [Sd] were also obtained. It was found that the existence of the bolts enhanced the local [Nu]，but the enhancement of the average [Nu] was limited. Within the range of research parameters，if the bolts’ spacing ratio remained constant，increase of the bolt diameter can effectively strengthen the heat transfer on the turbine casing surface around the embedded bolts，i.e. average [Nu] rose by 20% ～ 30% with the bolt diameter ratio [Dd] increasing from 2.67 to 5.33. If the [Dd] was constant，maximum [Nu] was obtained when [Sd] was 30.7. However，[Sd] affected the heat transfer on the turbine casing surface faintly，and the variation of the average [Nu] was within 10%.

Key words: High pressure turbine casing；Active clearance control；Set bolt；Heat transfer characteristics；Empirical formulas

摘要： 针对叶尖间隙主动控制系统的高压涡轮多层机匣，研究了机匣内部斜向冲击高肋结构中，定位螺栓对机匣换热特性的影响规律。试验中改变孔平均雷诺数[Re]([2543~7121])、螺栓直径与冲击孔直径比[Dd](2.67，4.13，5.33)、螺栓间距与冲击孔直径比[Sd](23.2，30.7，45.2)等参数，获得了不同工况下螺栓安装面局部和平均[Nu]数变化规律，并整理出对应的经验关系式。研究中发现，安装螺栓的存在，显著增强了机匣表面的局部换热效果，但是平均换热系数的提升幅度有限。研究结果表明，在本文试验参数范围内，当保持螺栓间距比不变时，增加螺栓直径可以有效强化机匣表面的换热系数，如当螺栓直径比[Dd]由2.67增加到5.33时，螺栓周围机匣表面平均[Nu]数增加幅度达20%～30%。当螺栓直径比保持不变的工况中，螺栓间距比[Sd]为[30.7]时机匣表面平均[Nu]数达到最大值，但是螺栓间距比参数对机匣表面换热系数影响相对较小，平均[Nu]数的变化幅度在10%以内。

关键词: 高压涡轮机匣；主动间隙控制；定位螺栓；换热特性；经验关系式

LIU Zhen-xiong^1,2,MAO Jun-kui²,JIANG Hua²,LI Jun-shan³,SHEN Yi³,LU Hai-ying³. Experimental Study of Effects of Bolts Inside Multilayer Turbine Casing on Heat Transfer Characteristics[J]. Journal of Propulsion Technology, 2017, 38(7): 1441-1449.

刘震雄,毛军逵,江华,李俊山,沈毅,陆海鹰. 多层涡轮机匣内螺栓对换热特性影响的试验研究[J]. 推进技术, 2017, 38(7): 1441-1449.

References

[1] 顾伟, 乔剑, 陈潇, 等. 民用航空涡扇发动机涡轮叶尖间隙控制技术综述[J]. 燃气轮机技术, 2003, 26(1): 1-4.
[2] Beitler R S, Saunders A A, Wanger R P. Fuel Conservation Through Active Control of Roter Clearance[R], AIAA 80-1087.
[3] Tallman J A, Lakshminarayana B. Methods for Desensitizing Tip Clearance Effects in Turbines[J]. ASME Journal of Turbomachinery, 2001, 20: 83-86.
[4] Lattime S B, Steinetz B M. High Pressure Turbine and Future Directions[J]. Journal of Propulsion and Power, 2004, 20: 302-311.
[5] 张清华. 发动机叶尖间隙技术[J]. 国际航空, 1987(2): 37-38.
[6] 张井山, 毛军逵, 李毅, 等. 高压涡轮主动间隙控机匣内换热特性试验[J]. 航空动力学报, 2014, 29(2): 298-304.
[7] Knipser C. Aircraft Performance Improvement by Active Clearance Control in Low Pressure Turbines[C]. ASME GT 2009-59301.
[8] Antonio Andreini, Riccardo Da Soghe. Experimental and Numerical Analysis of Multiple Impingement Jet Arrays for an Active Clearance Control System[J]. Journal of Turbomachinery, 2013, 135: 1-9.
[9] 姜远刚, 毛军逵, 李毅, 等. 间隙主动控制系统中冷却空气管换热特性实验研究[J]. 推进技术, 2014, 35(3): 366-371. (JIANG Yuan-gang, MAO Jun-kui, LI Yi, et al. Experimental Studies on Heat Transfer Characteristics in Air Cooling Pipe of Turbine Tip Clearance Control System[J]. Journal of Propulsion Technology, 2014, 35(3): 366-371.)
[10] Fangyuan Liu, Junkui Mao. Experimental Investigations about Heat Transfer Characteristics of Irregular Impingement Jet Arrays in Typical Active Clearance Control System[C]. Dalls: 31st AIAA Aerodynamic Measurement Technology and Ground Testing Conference, 2015.
[11] 张书华, 张丽, 朱惠人, 等. 涡轮机匣换热实验[J]. 航空动力学报, 2011, 26(5): 1011-1016.
[12] 单文娟, 毛军逵, 李毅, 等. 斜向冲击强化换热特性试验[J]. 航空动力学报, 2013, 28(3): 701-708.
[13] 路闯. 螺栓联接薄壁机匣结构强度计算方法研究[D]. 沈阳:沈阳航空航天大学, 2014.
[14] 周序. 航空发动机涡轮叶尖间隙主动控制系统传热问题的数值模拟[D]. 南京:南京航空航天大学, 2002.
[15] 乔剑. 涡轮叶尖间隙主动控制机匣内部流动与换热特性研究[D]. 南京:南京航空航天大学, 2010.
[16] 向定安, 张丽, 许都纯. 有射流冲击的短扰流柱排内柱面的传热实验[J]. 西北工业大学学报, 2002, 20(4): 586-589.
[17] 徐国强, 李莉, 丁水汀, 等. 带射流孔板矩形扰流柱通道内的壁面换热[J]. 推进技术, 2009, 30(1), 14-17. (XU Guo-qiang, LI Li, DING Shui-ting, et al. Heat Transfer in Rectangular Pin Finned Channel with Perfora Plate[J]. Journal of Propulsion Technology, 2009, 30(1): 14-17.)
[18] 蔡毅, 朱惠人, 王振伟. 冲击+扰流柱复合式结构换热特性的数值研究[J]. 科学技术与工程, 2012, 12(7): 1568-1572.
[19] 张井山. 某型高压涡轮机匣内部流动及换热特性研究[D]. 南京:南京航空航天大学, 2002.(编辑:史亚红)　　　　　　　　　　　　　　收稿日期:2016-03-02；修订日期:2016-06-06。作者简介:刘震雄,男,博士生,讲师,研究领域为航空发动机传热、传质研究以及稳定性。E-mail: nuaa1981@163.com