基于正交优化设计的诱导轮空化性能研究

doi:10.13675/j.cnki.tjjs.190020

推进技术 ›› 2020, Vol. 41 ›› Issue (2): 343-352.DOI: 10.13675/j.cnki.tjjs.190020

基于正交优化设计的诱导轮空化性能研究

张亚太¹,陈晖¹,项乐¹,陈炜¹,许开富²,李雨濛¹

1.西安航天动力研究所液体火箭发动机国防科技重点实验室，陕西西安 710100;2.西安航天动力研究所，陕西西安 710100

发布日期:2021-08-15
基金资助:
国家重大基础研究项目（613321）。

Study on Cavitation Performance of Inducer Based on Orthogonal Experiment

1.Science and Technology on Liquid Rocket Engine Laboratory，Xi’an Aerospace Propulsion Institute， Xi’an 710100， China;2.Xi’an Aerospace Propulsion Institute， Xi’an 710100, China

Published:2021-08-15

摘要/Abstract

摘要： 为了研究不同结构因素对诱导轮空化性能的影响及主次顺序，基于正交优化设计，采用数值模拟的方法，通过诱导轮可视化试验进行验证，对某型诱导轮及其改型进行了分析。仿真计算得到的不同空化数下空穴形态与实验结果吻合较好，断裂空化数的计算结果与实验结果误差为0.3%。仿真及实验结果表明，诱导轮发生扬程断裂不仅与空穴区占流道体积的大小有关，还与空穴区在流道中分布的位置有关，空穴区位置越靠后，越容易发生扬程断裂；对诱导轮空化性能及水力效率影响最大的结构因素为入口安放角，其次为入口修圆包角；入口等螺距段长度和变螺距段长度较小时可以提高诱导轮的空化性能。

关键词: 诱导轮;空化;正交优化设计;数值模拟

Abstract: In order to study the effects and the priorities of different structural factors on cavitation performance of inducer, an inducer and its modifications were analyzed based on the orthogonal experiment and numerical simulation, the results were verified by the visualization tests. Cavity structures at different cavitation numbers predicted by simulation were in good agreement with the experimental results, the error of breakdown cavitation number between simulation and experimental results was 0.3%. Simulation and experimental results show that the head breakdown of inducer is not only related to the size of the cavity volume in flow channel, but also related to the distribution of cavities. When the distribution of cavities develop further inside flow channel, the easier the head breakdown would occur. Inlet blade angle has the greatest affect on cavitation performance and hydraulic efficiency, followed by the leading edge sweepback wrap angle. The cavitation performance of inducer could be improved when the length of inlet equal- pitch parts and variable- pitch parts are smaller.

Key words: Inducer;Cavitation;Orthogonal experiment;Numerical simulation

张亚太,陈晖,项乐,陈炜,许开富,李雨濛. 基于正交优化设计的诱导轮空化性能研究[J]. 推进技术, 2020, 41(2): 343-352.

ZHANG Ya-tai¹,CHEN Hui¹,XIANG Le¹,CHEN Wei¹,XU Kai-fu²,LI Yu-meng¹. Study on Cavitation Performance of Inducer Based on Orthogonal Experiment[J]. Journal of Propulsion Technology, 2020, 41(2): 343-352.

参考文献

[1] 陈晖，李斌，张恩昭，等 . 液体火箭发动机高转速诱导轮旋转空化[J]. 推进技术， 2009， 30( 4): 390- 395.
[2] 潘中永，袁寿其 . 泵空化基础[M]. 镇江：江苏大学出版社， 2013.
[3] Giovanni Pace ， Dario Vakentini ， Angelo Pasini ， et al . Geometry Effects on Flow Instabilities of Different Three-Bladed Inducers[J]. Journal of Fluids Engineering， 2015， 137( 4).
[4] Coutier D O ， Caignaert G ， Bois G . Influence of the Blade Number on Inducer Cavitaing Behavior[J]. Journal of Fluids Engineering， 2012， 134( 8).
[5] Imene Mejri ， Farid Bakir ， Robert Rey ， et al . Comparison of Couputational Results Obtained from a VOF Cavitation Model with Experimental Investigations of Three Inducers[C]. Houston： Proceeding of the ASME 2005 Fluid Enginnering Division Summer Meeting， 2005.
[6] Imene Mejri ， Farid Bakir ， Robert Rey ， et al . Comparison of Computational Results Obtained from a Homogeneous Cavitation Model with Experimental Investigations of Three Inducers[J]. Journal of Fluids Engineering， 2006， 128( 6): 1308- 1323.
[7] Bakir F ， Kouidri S ， Noguera R ， et al . Experimental Analysis of an Axial Inducer Influence of the Shape of the Blade Leading Edge on the Performances in Cavitating Regime[J]. Journal of Fluids Engineering， 2003， 125( 2): 293- 301.
[8] 李仁年，毕祯，黎义斌，等 . 诱导轮偏转角对离心泵叶轮空化性能的影响[J]. 排灌机械工程学报， 2016， 34( 6): 461- 469.
[9] 郭晓梅，朱祖超，崔宝玲，等 . 诱导轮内流场数值计算及汽蚀特性分析[J]. 机械工程学报， 2010， 46( 4): 122- 128.
[10] 唐飞，李家文 . 提高氧泵诱导轮汽蚀性能的方法研究[J]. 航空动力学报， 2008， 23( 9): 1743- 1747.
[11] 陈懋章 . 粘性流体动力学基础[M]. 北京：高等教育出版社， 2004.
[12] Zwart P J ， Gerber A G ， Belamr I T . A Two-Phase Flow Model for Predicting Cavitation Dynamics[C]. Yokohama： Proceedings of the 5th International Conference on Multiphase Flow， 2004.
[13] 项乐，陈晖，谭永华，等 . 诱导轮空化热力学效应实验研究进展[C]. 北京：第 11届全国水力机械及其系统学术年会， 2018.
[14] 许少华，侯中喜，葛爱学，等 . 锥导乘波构型设计、优化与分析[J]. 推进技术， 2008， 29( 4): 448- 453.
[15] Xiaojun Li， Zhiwu Jiang， Zuchao Zhu， et al . Entropy Generation Analysis for the Cavitating Head-drop Characteristic of a Centrifugal Pump[J]. Proceeding of the Institution of Mechanical Engineers Part C:Journal of Mechanical Engineering Science， 2018， ( 1): 1- 10.

基于正交优化设计的诱导轮空化性能研究

Study on Cavitation Performance of Inducer Based on Orthogonal Experiment

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 0

编辑推荐

Metrics

本文评价