周向布局对高压比串列离心压气机性能的影响

doi:10.13675/j.cnki.tjjs.190094

推进技术 ›› 2020, Vol. 41 ›› Issue (4): 820-829.DOI: 10.13675/j.cnki.tjjs.190094

周向布局对高压比串列离心压气机性能的影响

康达¹，何卫东²，徐毅³，刘志杰³

1.大连派思燃气系统股份有限公司，辽宁大连 116600;2.大连交通大学机械工程学院，辽宁大连 116028;3.大连派思透平动力科技有限公司，辽宁大连 116600

发布日期:2021-08-15

Effects of Clocking Arrangement on Performance of HighPressure Ratio Tandem Centrifugal Compressor

1.Dalian Energas Gas System Co.,Ltd.,Dalian 116600,China;2.School of Mechanical Engineering,Dalian Jiaotong University,Dalian 116028,China;3.Dalian Energas Turbine Power Technology Co.,Ltd.,Dalian 116600,China

Published:2021-08-15

摘要/Abstract

摘要： 为揭示周向布局对高压比串列离心压气机性能的影响机制，采用经试验数据确认的数值方法，对串列叶轮在典型周向布局下的性能及流场结构进行了分析。研究表明：周向布局对串列叶轮流动的影响主要体现在后排叶轮的叶顶区域， 75%周向位置时压气机级性能最优，25%周向位置时最差；串列叶轮改善离心压气机流场的物理机制为诱导轮压力侧气流对导风轮吸力面附面层的吹除效应，以及导风轮吸力面侧流体对诱导轮尾迹的引射效应；高压比串列离心压气机周向布局的优化应遵循的原则是，在避免诱导轮尾迹与导风轮吸力面发生直接作用的前提下，应采用较大的周向偏置参数。

关键词: 离心压气机;串列叶轮;周向布局;流场特性;数值模拟

Abstract: In order to reveal effects of the clocking arrangement on performance of high pressure ratio tandem centrifugal compressor, based on numerical simulation method validated by experimental data, the overall performance and flow field structures of the tandem impeller with typical clocking arrangements are analyzed. Results indicate that influence of the clocking arrangement on tandem impeller flow is mainly ascribed to the tip region of the rear impeller. The compressor stage performance is optimum with 75% clocking arrangement, while it is the worst with 25% clocking arrangement. The mechanisms of tandem design improving centrifugal compressor flow field include the blowoff effect of the airflow near inducer pressure surface on the boundary layer of exducer suction surface, and the ejection effect of the fluid near exducer suction surface on the wake of inducer blade. The design principle for the clocking arrangement of high pressure ratio tandem centrifugal compressors is to adopt a high value of the circumferential offset, on the premise of guaranteeing the wake of inducer blade not to directly interact with the exducer suction surface.

Key words: Centrifugal compressor;Tandem impeller;Clocking arrangement;Flow field characteristics;Numerical simulation

康达，何卫东，徐毅，刘志杰. 周向布局对高压比串列离心压气机性能的影响[J]. 推进技术, 2020, 41(4): 820-829.

KANG Da¹, HE Wei-dong², XU Yi³, LIU Zhi-jie³. Effects of Clocking Arrangement on Performance of HighPressure Ratio Tandem Centrifugal Compressor[J]. Journal of Propulsion Technology, 2020, 41(4): 820-829.

参考文献

[1] Krain H. Review of Centrifugal Compressor’s Application and Development[R]. ASME GT 2003-38971.
[2] McGlumphy J. Numerical Investigation of Subsonic Axial-Flow Tandem Airfoils for a Core Compressor Rotor[D]. Blacksburg: Virginia Polytechnic Institute and State University, 2008.
[3] Canon F. Numerical Investigation of the Flow in Tandem Compressor Cascades[D]. Vienna: Vienna University of Technology Institute of Thermal Power Plants， 2004.
[4] Brent J A， Clemmons D R. Single-Stage Experimental Evaluation of Tandem-Airfoil Rotor and Stator Blading for Compressors[R]. NASA-CR-134713， 1974.
[5] Bammert K， Beelte H. Investigations of an Axial Flow Compressor with Tandem Cascades[J]. Journal of Engineering for Gas Turbines and Power， 1980， 102(4): 971-977.
[6] Bache G. Impeller Tandem Blade Study with Grid Embedding for Local Grid Refinement[R]. NASA-N 92-32278.
[7] Josuhn-Kadner B， Hoffmann B. Investigations on a Radial Compressor Tandem-Rotor Stage with Adjustable Geometry[J]. Journal of Turbomachinery， 1993， 115(3): 552-559.
[8] Josuhn-Kadner B. Flow Field and Performance of a Centrifugal Compressor Rotor with Tandem Blades of Adjustable Geometry[R]. ASME 94-GT-13.
[9] Roberts D A， Kacker S C. Numerical Investigation of Tandem-Impeller Designs for a Gas Turbine Compressor [R]. ASME 2001-GT-324.
[10] Erdmenger R R， Michelassi V. Influence of Tandem Inducers on the Performance of High Pressure Ratio Centrifugal Compressor[R]. ASME GT 2015-43001.
[11] 李紫良，卢新根，张燕峰，等. 高压比离心压气机串列叶轮内部流动机理研究[J] 推进技术， 2017， 38(10): 2393-2400.
[12] 王宝潼，张楚华，席光，等. 串列叶片式离心叶轮内流场的数值研究[J]. 西安交通大学学报， 2007， 41(11): 1275-1278.
[13] Krain H. CAD Method for Centrifugal Compressor Impeller[J]. Journal of Engineering for Gas Turbines and Power， 1984， 106(2): 428-488.
[14] Krain H， Hoffman W. Verification of an Impeller Design by Laser Measurements and 3D-Viscous Flow Calculations[R]. ASME 89-GT-159.
[15] 席光. 关于Krain实验叶轮几何型线及其流道二次流旋涡结构的讨论[J]. 工程热物理学报， 2000， 21(4): 440-442.
[16] Oh J J. The Effects of Blade Fillets on Aerodynamic Performance of High Pressure Ratio Centrifugal Compressor[C]. West Lafayette: The 23rd International Compressor Engineering Conference at Purdue， 2016.
[17] Krain H. Swirling Impeller Flow[J]. Journal of Turbomachinery， 1988， 110(1): 122-128.
[18] Hah C， Krain H. Secondary Flows and Vortex Motion in a High-Efficiency Backswept Impeller at Design and Off-Design Conditions[R]. ASME 89-GT-181.
[19] 孙志刚. 离心压气机内部流动特性与流场结构研究[D]. 北京: 中国科学院研究生院， 2011.
[20] Hirsch C， Kang S， Pointel G. A Numerically Supported Investigation of the 3D Flow in Centrifugal Impellers: Part I-The Validation Base[R]. ASME 96-GT-151.

周向布局对高压比串列离心压气机性能的影响

Effects of Clocking Arrangement on Performance of HighPressure Ratio Tandem Centrifugal Compressor

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 0

编辑推荐

Metrics

本文评价