喷水射流预冷对发动机进气温度及流场变化影响的数值研究

doi:10.13675/j.cnki.tjjs.190819

推进技术 ›› 2020, Vol. 41 ›› Issue (9): 1999-2010.DOI: 10.13675/j.cnki.tjjs.190819

喷水射流预冷对发动机进气温度及流场变化影响的数值研究

陆禹铭¹，徐倩楠²，吴锋²，张海¹

1.哈尔滨工程大学能源与动力学院,黑龙江哈尔滨 150001;2.中国航发四川燃气涡轮研究院高空模拟技术重点实验室,四川绵阳 621700

出版日期:2020-09-15 发布日期:2020-09-15
作者简介:陆禹铭，硕士生，研究领域为航空发动机内部两相流动。E-mail：heulym@163.com
基金资助:
中央高校基本科研业务费专项基金（3072019CFJ0309）。

Numerical Study on Effects of Water Injection Pre-Compressor Cooling on Engine Inlet Temperature and Flow Field Change

1.College of Energy and Power,Harbin University of Engineering,Harbin 150001,China;2.Science and Technology on Altitude Simulation Laboratory,AECC Sichuan Gas Turbine Establishment, Mianyang 621700,China

Online:2020-09-15 Published:2020-09-15

摘要/Abstract

摘要： 射流预冷技术可以有效降低进气温度并提高航空发动机的性能。为探究该技术在高空环境下对流场问题的影响，采用径向均匀射流方案，模拟高空条件，结合水滴的蒸发过程以及气液两相的耦合作用对预冷段射流喷水的情形进行数值计算。结果表明，径向喷射方案能够有效降低进气温度，在各个工况中，温降系数约为8%~26.7%；在高温工况中提高喷水量可以有效提高温降效果，工况6的喷水量和工作温度都是最大的，温降系数和蒸发效率分别达到了最高值的26.7%和73.9%；预冷段的压降损失和出口流场均匀度取决于来流马赫数和喷水量，高马赫数和较大的喷水量都会加剧压损与流场的紊乱程度，由于工况6的高射流量和气流马赫数，其在喷水装置处的压降系数达到了最大值的5.8%。

关键词: 射流预冷;预冷段;流场特性;高温;蒸发

Abstract: Mass Injection and Pre-Compressor Cooling (MIPCC) technology has influence on reducing temperature of inlet air to improve the engine performance. In order to explore the effect of technology on the field at high altitude environments, the radial even spray arrangement is adopted to simulate altitude conditions to investigate air/droplet fully coupled cooling and evaporation of water in the cooling section with numerical study. The results indicate that the temperature of inlet air is effectively reduced by the radial arrangement of nozzles. Values of temperature drop coefficient can achieve 8%~26.7% among cases. Then, it is a better method to reduce the temperature of inlet air by raising the injection flow at higher operating temperature. The temperature drop coefficient and evaporation efficiency can achieve the largest value of 26.7% and 73.9% for case 6 with higher injection rate and temperature of inlet air. Moreover, larger amount of the injection flow and inlet air at higher Mach number will deteriorate the total pressure loss and the flow field uniformity, the total pressure drop coefficient gets the largest value of 5.8% at the location of spray system for case 6 with largest injection rate and highest Mach number of inlet air.

Key words: Mass injection and pre-compressor cooling;Cooling section;Flow field characteristic;High temperature;Evaporation

陆禹铭，徐倩楠，吴锋，张海. 喷水射流预冷对发动机进气温度及流场变化影响的数值研究[J]. 推进技术, 2020, 41(9): 1999-2010.

LU Yu-ming¹, XU Qian-nan², WU Feng², ZHANG Hai¹. Numerical Study on Effects of Water Injection Pre-Compressor Cooling on Engine Inlet Temperature and Flow Field Change[J]. Journal of Propulsion Technology, 2020, 41(9): 1999-2010.

参考文献

[1] Wilcox E C,Trout A M. Analysis of Thrust Augmentation of Turbojet Engines by Water Injection at Compressor Inlet Including Charts for Calculating Compression Processes with Water Injection[R]. NACA 51-TR-1006.
[2] Trout A M. Theoretical Turbojet Thrust Augmentation by Evaporation of Water During Compression as Determined by Use of a Mollier Diagram[R]. NACA 50-TN-2104.
[3] Henneberry H M, Snyder C A. Analysis of Gas Turbine Engines Using Water and Oxygen Injection to Achieve High Mach Numbers and High Thrust[R]. NASA 93-TM-106270.
[4] Burkardt L A, Norris R. The Design and Evolution of the Beta Two-Stage-To-Orbit Horizontal Takeoff and Landing Launch System[R]. AIAA 92-5080.
[5] Bartolotta P A, Mcnelis N B, Shafer D G. High Speed Turbines: Development of a Turbine Accelerator (RTA) for Space Access[R]. AIAA 2003-6943.
[6] Balepin V, Carter P, Spath T, et al. MIPCC Technology Development[R]. AIAA 2003-6929.
[7] Cater P, Balepin V. Mass Injection and Pre-Compressor Cooling Engines Analyses[R]. AIAA 2002-4127.
[8] Alhazmy M M, Najjar Y S H. Augmentation of Gas Turbine Performance Using Air Coolers[J]. Applied Thermal Engineering, 2004, 24(2-3): 415-429.
[9] Kim K H, Ko H J, Perez-Blanco H. Analytical Modeling of Wet Compression of Gas Turbine Systems[J]. Applied Thermal Engineering, 2011, 31(5): 834-840.
[10] Mahto D, Pal S. Thermodynamics and Thermo-Economic Analysis of Simple Combined Cycle with Inlet Fogging[J]. Applied Thermal Engineering, 2013, 51(1-2): 413-424.
[11] Lin A Q, Sun Y G, Zhang H, et al. Fluctuating Characteristics of Air-Mist Mixture Flow with Conjugate Wall-Film Motion in a Compressor of Gas Turbine[J]. Applied Thermal Engineering, 2018, 142: 779-792.
[12] Lin A Q, Zhou J, Fawzy H, et al. Evaluation of Mass Injection Cooling on Flow and Heat Transfer Characteristics for High-Temperature Inlet Air in a MIPCC Engine[J]. International Journal of Heat and Mass Transfer, 2019, 135: 620-630.
[13] Lin A Q, Zheng Q, Fawzy H, et al. Sensitivity of Air/Mist Nonequilibrium Phase Transition Cooling to Transient Characteristics in a Compressor of Gas Turbine[J]. International Journal of Heat and Mass Transfer, 2019, 137: 882-894.
[14] Elwekeel F N M, Abdala A M M. Effect of Mist Cooling Technique on Exergy and Energy Analysis of Steam Injected Gas Turbine Cycle[J]. Applied Thermal Engineering, 2016, 98(5): 298-309.
[15] Kim K H, Ko H J, Kim K, et al. Analysis of Water Droplet Evaporation in a Gas Turbine Inlet Fogging Process[J]. Applied Thermal Engineering, 2012, 33-34: 62-69.
[16] Zhang H, Luo M C, Pan X J, et al. Numerical Analysis of Gas Turbine Inlet Fogging Nozzle Manifold Resistance[J]. Proceedings of the Institution of Mechanical Engineers， Part A： Journal of Power and Energy, 2016, 230: 63-75.
[17] Lin A Q, Zhou J, Fawzy H, et al. Effect of Water Injection Cooling on Flow Field Characteristics in the Cooling Section of Precooled Turbine-Based Combined Cycle Engine[J]. International Journal of Heat and Mass Transfer, 2019, 141: 615-626.

喷水射流预冷对发动机进气温度及流场变化影响的数值研究

Numerical Study on Effects of Water Injection Pre-Compressor Cooling on Engine Inlet Temperature and Flow Field Change

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 0

编辑推荐

Metrics

本文评价