亚声速无人机S弯进气道的多点多目标优化设计

doi:10.13675/j.cnki.tjjs.200104

推进技术 ›› 2021, Vol. 42 ›› Issue (3): 495-504.DOI: 10.13675/j.cnki.tjjs.200104

亚声速无人机S弯进气道的多点多目标优化设计

曾丽芳¹，胡建新²，潘定一¹，黎军¹，邵雪明¹

1.浙江大学航空航天学院，浙江杭州 310027;2.浙江理工大学机械与自动控制学院，浙江杭州 310018

出版日期:2021-03-15 发布日期:2021-08-15
作者简介:曾丽芳，博士生，研究领域为无人机气动与总体设计，新概念飞行器。E-mail：lifang_zeng@zju.edu.cn
基金资助:
国家自然科学基金（51906224）。

Multi-Points and Multi-Objective Optimization Design of Subsonic UAV S-Shaped Inlet

1.School of Aeronautics and Astronautics，Zhejiang University，Hangzhou 310027，China;2.Faculty of Mechanical Engineering & Automation，Zhejiang Sci-Tech University，Hangzhou 310018，China

Online:2021-03-15 Published:2021-08-15

摘要/Abstract

摘要： 为提高亚声速无隔道式S弯进气道的整体气动性能，以提高总压恢复系数和降低畸变指数为设计目标，结合高精度数值模拟方法与第二代非劣排序遗传算法（NSGA-II），开展了无隔道式S弯进气道在马赫数0.25和0.7时的多目标优化设计。整个优化流程基于400个样本，最终得到四幅有效Pareto前沿图。从总压畸变Pareto前沿图中选取出优化算例并与原始进气道进行对比，结果表明：优化后的进气道中心线斜率入口段小、出口段大，而横截面面积分布的曲线斜率恰好相反；优化后的进气道低压区缩小、流动分离得到有效控制；虽然总压恢复系数提高有限，但是总压畸变得到大幅降低，在马赫数为0.25和0.7时，分别降低15.86%和23.61%。优化后的进气道在马赫数0.25~0.7整体性能得到有效改善。将该优化设计方法进一步推广应用于3个马赫数下的多点多目标优化设计，并得到了三维Pareto前沿图。

关键词: S弯进气道;多点优化设计;总压恢复;总压畸变;数值模拟

Abstract: In order to increase the performance of subsonic diverterless S-shaped inlet within a range of Mach number， a multi-objective optimization system for S-shaped diverterless inlet was established， and the Mach numbers are 0.25 and 0.7. With the design objective of increasing total pressure recovery coefficient and decreasing distortion， the optimization system combined the numerical simulation method with Non-dominated Sorting Genetic Algorithm II （NSGA-II）. The optimization case was based on 400 samples and four Pareto Front figures were obtained. An optimized design was chosen from the distortion Pareto Front figure. Compared with the original inlet， the slope of the optimized centerline is smaller at the entrance and larger at the exit， while the distribution of the optimized cross section area is reverse. Low pressure areas are obviously shrunk and flow separation is effectively reduced after optimization. Although the improvement of the total pressure recovery coefficient is limited， the total pressure distortion is significantly redued， with a decrease of 15.86% at Ma 0.25 and 23.61% at Ma 0.7， respectively. In conclusion， the overall performance of the optimized inlet is effectively improved within Mach number 0.25~0.7. The optimization design method has been applied to multi-objective optimization design under three Mach numbers， and several 3D Pareto Front figures are obtained.

Key words: S-shaped inlet;Multi-points optimization design;Total pressure recovery;Total pressure distortion;Numerical simulation

曾丽芳，胡建新，潘定一，黎军，邵雪明. 亚声速无人机S弯进气道的多点多目标优化设计[J]. 推进技术, 2021, 42(3): 495-504.

ZENG Li-fang¹, HU Jian-xin², PAN Ding-yi¹, LI Jun¹, SHAO Xue-ming¹. Multi-Points and Multi-Objective Optimization Design of Subsonic UAV S-Shaped Inlet[J]. Journal of Propulsion Technology, 2021, 42(3): 495-504.

参考文献

[1] Wellborn S R， Reichert B A， Okiishi T H. An Experimental Investigation of the Flow in a Diffusing S-duct［R］. AIAA 92-3622.
[2] 谭慧俊，郭荣伟. 一种背负式无附面层隔道进气道的数值模拟研究与实验验证［J］. 航空学报， 2004， 25（6）： 540-545.
[3] Lefantzi S， Knight D D. Automated Design Optimization of a Three-Dimensional S-Shaped Subsonic Diffuser［J］. Journal of Propulsion and Power， 2002， 18（4）： 913-921.
[4] Bae HyoGil， Park SooHyung， Kwon JangHyuk. Efficient Global Optimization for S-duct Diffuser Shape Design［J］. Proceedings of the Institution of Mechanical Engineers Part G： Journal of Aerospace Engineering， 2013， 227： 1516-1532.
[5] Zhang J M， Wang C F， Lum K Y . Multidisciplinary Design of S-Shaped Intake［C］. Honolulu： 26th AIAA Applied Aerodynamics Conference， 2008.
[6] 甘文彪，周洲，许晓平，等. S弯进气道优化设计及分析［J］. 推进技术， 2014， 35（10）： 1317-1324.
[7] 刘雷，宋彦萍，陈焕龙，等. 半埋入式S弯进气道设计及其优化［J］. 推进技术， 2014， 35（10）： 1303-1309.
[8] Berrier B L， Carter M B， Allan B G. High Reynolds Number Investigation of a Flush-Mounted， S-Duct Inlet with Large Amounts of Boundary Layer Ingestion［R］. NASA/TP-2005-213766.
[9] Richard R J. An Investigation of Several NACA 1-series Inlets at Mach Numbers from 0.4 to 1.29 for Mass Flow Ratios near 1.0［R］. NASA TM X-3324， 1975.
[10] 靖建朋，郭荣伟. 弹用S弯进气道气动性能试验［J］. 航空动力学报， 2009， 24（9）： 2085-2090.
[11] 万大为，郭荣伟，艾清，等. 一种S弯进气道的设计与实验研究［J］. 南京航空航天大学学报， 2004， 36（2）： 14-18.
[12] Goldsmith E L， Seddon J. Practical Intake Aerodynamic Design［M］. Washington DC： AIAA Education Series， 1993.
[13] Lee B J， Kim C. Automated Design Methodology of Turbulent Internal Flow Using Discrete Adjoint Formulation［J］. Aerospace Science and Technology， 2007， 11（2）： 163-173.
[14] 刘雷，陈浮，宋彦萍，等. 半埋入式S弯进气道主动流动控制研究［J］. 推进技术， 2014， 35（9）： 1168-1173.
[15] Zeng Lifang， Pan Dingyi， Ye Shangjun， et al. A Fast Multiobjective Optimization Approach to S-duct Scoop Inlets Design with both Inflow and Outflow［J］. Proceedings of the Institution of Mechanical Engineers， Part G： Journal of Aerospace Engineering， 2019， 233（9）： 3381-3394.
[16] Piegl L， Tiller W. The Nurbs Book（Monographs in Visual Communication）［M］. Berlin： Springer， 1997.
[17] Deb K D， Pratap A， Agarwal S， et al. A Fast and Elitist Multiobjective Genetic Algorithm： NSGA-II［J］. IEEE Transactions on Evolutionary Computation 2002， 6（2）： 182-197.

亚声速无人机S弯进气道的多点多目标优化设计

Multi-Points and Multi-Objective Optimization Design of Subsonic UAV S-Shaped Inlet

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 0

编辑推荐

Metrics

本文评价