间隙高度对某涡轮叶尖间隙泄漏流影响的研究

推进技术 ›› 2012, Vol. 33 ›› Issue (4): 566-572.

间隙高度对某涡轮叶尖间隙泄漏流影响的研究

王大磊,朴英

清华大学航天航空学院,北京 100084;清华大学航天航空学院,北京 100084

发布日期:2021-08-15
作者简介:王大磊(1986—),男,博士生,研究领域为航空发动机气动热力学研究。E-mail:13810498953@139.com

Influence of Tip Clearance Size on Tip Clearance Flow of a Transonic Turbine

School of Aerospace, Tsinghua University, Beijing 100084,China;School of Aerospace, Tsinghua University, Beijing 100084,China

Published:2021-08-15

摘要/Abstract

摘要： 利用三维湍流数值模拟方法模拟某跨声速高压涡轮流场,研究了转子叶尖间隙高度对涡轮转子间隙泄漏流动的影响,详细描述了间隙流动结构随间隙高度的变化情况。研究结果表明:随着间隙高度的增加,间隙泄漏流流量线性增加,并导致转子叶尖附近流体偏转角度减小。间隙高度每增加1%相对叶高,间隙泄漏流量占总流量的比例约增加2.1%。间隙高度变化对间隙内部流动的影响明显:当间隙比较小时,随着间隙高度的增加,分离泡的大小迅速增加,回流区域减小。随着间隙高度的增加,间隙泄漏涡尺度迅速增加,同时由于泄漏流中高速流体流量增加,通道涡远离叶片吸力面并向靠近机匣的方向移动,泄漏涡也向远离吸力面方向运动。

关键词: 涡轮;叶尖间隙;叶尖间隙流;泄露涡;数值模拟

Abstract: The influence of the tip clearance height of turbine rotor blades on tip clearance flow of an axial turbine stage was investigated by numerical simulation and different tip clearance heights were taken into account. Results show that the leakage flow rate would increase markedly due to the increase of the tip clearance height. The ratio of the leakage flow rate and total flow rate would increase 2.1% as the tip clearance height increased 1% of the blade height. From analyzing the flow field, it indicates that as the height of tip clearance increases, the flow structure in the tip clearance changes. When the height of tip clearance is small, the size of the separation bubble increases quickly as the height of tip clearance increases, meanwhile, the size of the leakage vortex gets larger as well as the flow rate of high speed leakage flow. The passage vortex and the leakage vortex are pushed off from the blade, the flow structure of secondary flow near the tip clearance changes while the height of tip clearance increases. 

Key words: Turbine; Tip clearance; Tip clearance flow; Loss vortex;Numerical simulation

王大磊,朴英. 间隙高度对某涡轮叶尖间隙泄漏流影响的研究[J]. 推进技术, 2012, 33(4): 566-572.

参考文献

[2] Rao N M, Camci C.Axial Turbine Tip Desensitization by Injection from a Tip Trench Part1:Effect of Injection Mass Flow Rat[R].ASME 2004-GT-53256.
[3] Rao N M, Camci C.Axial Turbine Tip Desensitization by Injection from a Tip Trench Part 2:Leakage Flow Sensitivity to Injection Location[R].ASME 2004-GT- 53258.
[4] Moore J, Tilton J S.Tip Leakage Flow in a Linear Turbine Cascade [J].ASME Journal of Turbomachinery, 8,0(1):18-26.
[5] Bindon J P.The Measurement and Formation of Tip Clearance Loss[J].ASME Journal of Turbomachinery, 9,1(3):257-263.
[6] Yamamoto A.Endwall Flow/Loss Mechanisms in a Linear Turbine Cascade with Blade Tip Clearance[J]. ASME Journal of Turbomachinery,9,1(2):246-275.
[7] Xinwen Xiao, McCarter Andrew A.Tip Clearance Effects in a Turbine Rotor:Part I-Pressure Field and Loss[R].ASME 2001-GT-0476.
[8] McCarter Andrew A, Xinwen Xiao.Tip Clearance Effects in a Turbine Rotor Flow Part II-Velocity Field and Physics[R].ASME 2001-GT-0477.
[9] Xinwen Xiao.Investigation of Tip Clearance Flow Physics in Axial Flow Turbine Rotors[D]. Pennsylvania: The Pennsylvania State University, 2000.
[10] 许开福, 乔渭阳.涡轮叶尖间隙流动的数值模拟[J].热能动力工程, 2009.24(4):432-436.
[11] 祁明旭, 丰镇平.透平动叶顶部间隙流的表现形式及其对透平性能的影响[J].西安交通大学学报, 5,9(3):244-246.
[12] 祁明旭, 丰镇平.透平动叶顶部间隙流的端壁二次流结构研究[J].西安交通大学学报, 5,9(5):445-449.
[13] Yang H, Chen Hamnching, Han Jechin．Flow and Heat Transfer Prediction on Turbine Rotor with Various Tip Configurations[R]．AIAA 2005-573.
[14] Krishnababu S S,Newton P J,Dawes W N, et al.Aerothermal Investigations of Tip Leakage Flow in Axial Flow Turbines—Part I:Effect of Tip Geometry and Tip Clearance Gap[J].Journal of Turbomachinery, 9,1(1).
[15] Li Wei, Qiao Weiyang．Numerical Simulation of Active Control on Tip Leakage Flow in Axial Turbine[J]．Chinese Journal of Aeronautics,9,2:129-137.
[16] 牛茂升,藏述升.间隙高度对涡轮叶顶间隙流动的影响[J].工程热物理学报, 8,9(6):935-939.
[17] 牛茂升.涡轮间隙流动主动控制的试验研究及数值模拟[D].上海:上海交通大学, 2010.
[18] L S.Secondary Flows in Axial Turbines-A Review[J].Heat Transfer in Gas Turbine Systems, 2001,934:11-16.