基于源项法的气膜冷却涡轮叶片多目标优化

推进技术 ›› 2013, Vol. 34 ›› Issue (10): 1339-1344.

基于源项法的气膜冷却涡轮叶片多目标优化

尹钊,方祥军

北京航空航天大学能源与动力工程学院,北京 100191;北京航空航天大学能源与动力工程学院,北京 100191

发布日期:2021-08-15
作者简介:尹钊(1987—),男,博士生,研究领域为叶轮机械气动热力学。E-mail:yinzhao-2008@163.com

Multi-Objective Optimization of Film-Cooled Turbine with Source Term Method

School of Power and Energy, Beijing University of Aeronautics and Astronautics, Beijing 100191, China;School of Power and Energy, Beijing University of Aeronautics and Astronautics, Beijing 100191, China

Published:2021-08-15

摘要/Abstract

摘要： 以GE-E³高压涡轮第一级气冷导叶为研究对象,通过多目标遗传算法优化气膜孔布局以降低叶片表面温度。其中采用源项法模拟全场气膜冷却效果,该方法节省计算量的同时无需对气膜孔划分网格,通过对比实验结果后认为,源项法可以较好地模拟出冷气覆盖效果如表面动量损失等。在此基础上采用多目标遗传算法NSGA-II (Nondominated Sorting Genetic Algorithm II),以气膜孔的出气角及流向位置为设计变量,以叶片表面最高温度及平均温度为优化目标。结果表明叶片表面温度分布有所改善,其中压力面优化效果要好于吸力面。 

关键词: 涡轮;气膜冷却;数值模拟;源项法;多目标优化 

Abstract: A multi-objective genetic algorithm optimization procedure was demonstrated on the film cooled stator of the first high pressure stage of GE-E^3to decrease the temperature on the blade. Firstly, source term method was employed to simulate the effect of overall film cooling, considering it was cheap in term of CPU consumption and did not require any mesh adaption in the presence of cooling holes. The loss of momentum near the wall caused by the injected coolant could be observed from the simulated results, which agreed well with the experimental results. Secondly, multi-objective optimization method NSGA-II (Nondominated Sorting Genetic Algorithm II) was used to minimize the maximum temperature and average temperature of the blade. The inject angles and streamwise positions were varied in the design space. The results demonstrate that the temperature distribution on the blade has been improved, and the pressure side has better cooling effect compared with suction side. 

Key words: Turbine; Film cooling; Numerical simulation; Source term method; Multi-objective optimization

尹钊,方祥军. 基于源项法的气膜冷却涡轮叶片多目标优化[J]. 推进技术, 2013, 34(10): 1339-1344.

YIN Zhao,FANG Xiang-jun. Multi-Objective Optimization of Film-Cooled Turbine with Source Term Method[J]. Journal of Propulsion Technology, 2013, 34(10): 1339-1344.

参考文献

[1] 韩介勤,杜达,艾卡德,等.燃气轮机传热和冷却技术[M].西安: 西安交通大学出版社,2005.
[2] 向安定,刘松龄,朱惠人,等.涡轮工作叶片表面气膜冷却效率的实验研究[J].推进技术,2004,25(1):39-43.(Xiang An-ding, LIU Song-ling, ZHU Hui-ren,et al.Film Cooling Effectiveness Measurements for Gas Holes on Blade Surface in a Turbine Cascade[J].Journal of Propulsion Technology, 2004,5(1):39-43.)
[3] 雷云涛,袁新.涡轮叶片前缘双排孔气膜冷却数值模拟[J].推进技术,2012,33(5):704-709.(LEI Yun-tao, YUAN Xin.Numerical Simulation on the Effect of Film Cooling at Leading Edge of Turbine Blade with Two Rows of Staggered Holes[J].Journal of Propulsion Technology, 2012,3(5): 704-709.)
[4] Hildebrandt Th, Ettrich J, Kluge M, et al.Unsteady 3D Navier-Stokes Calculation of a Film-cooled Turbine Stage with Discrete Cooling Holes[M].Netherlands:Springer, 2006:533-549.
[5] Tartinville B, Hirsch Ch.Modeling of Film Cooling for Turbine Blade Design[R].ASME 2008-GT-50316.
[6] Burdet A, Abhari R S, Rose M G.Modeling of Film Cooling:Part 2-Model for Use in 3D CFD[R].ASME 2005-GT-68780.
[7] He Li.Block-Spectral Approach to Film-cooling Modeling[J].Journal of Turbomachinery, 2012,4(2):1-8.
[8] Turner M G, Vitt P H.Multistage Simulations of the GE90Turbine[R].NASA CR-1999-209311.
[9] Zhi-gang Liu, Xiang-jun Fang, Si-yong Liu, et al.Research of Aerodynamic Performance of HP-Turbine with Coolant Injections for Variable Cycle Engine[J].Journal Applied Mechanics and Materials,2012,0:1047-1053.
[10] 曾军,王彬,康勇.气膜冷却涡轮导向叶片流场数值模拟[J].燃气涡轮试验与研究,2006,19(4):16-19.
[11] Mousavi A, Nadarajah S K.Adjoint-Based Multidisciplinary Design Optimization of Cooled Gas Turbine Blades[R].AIAA 2011-1131.
[12] Johnson J J, King P I.Three-Dimensional Film-cooled Vane CFD Simulations and Preliminary Comparison to Experiments[R].AIAA 2011-0499.
[13] Johnson J J, Clark J P, Ooten M K.Design Optimization Methods for Improving HPT Vane Pressure Side Cooling Properties Using Genetic Algorithms and Efficient CFD[R].AIAA 2012-0326.
[14] Timko L P.Energy Efficient Engine High Pressure Turbine Component Test Performance Report[R].NASA CR-1984-168289.
[15] 高效节能发动机文集编委会.高效节能发动机文集(卷5)[M].北京:航空工业出版社,1991.
[16] Halila E E, Lenahan D T, Thomas T T.Energy Efficient Engine High Pressure Turbine Test Hardware Detailed Design Report[R].NASA CR-1982-167955.
[17] Lin Y, Song B, Li B, et al.Measured Film Cooling Effectiveness of Three Multihole Patterns[J].Journal of Heat Transfer, 2006,8(2):192-197.
[18] Deb K, Pratap A, Agarwal S, et al.A Fast and Elitist Multiobjective Genetic Algorithm:NSGA-II[J].IEEE Transactions on.Evolutionary Computation, 2002,6(2):182-197.