涡流冷却推力室燃烧效率分析

推进技术 ›› 2013, Vol. 34 ›› Issue (11): 1507-1512.

涡流冷却推力室燃烧效率分析

李家文,王化余,叶汉玉,俞南嘉

北京航空航天大学宇航学院,北京 100191;北京航空航天大学宇航学院,北京 100191;北京航空航天大学宇航学院,北京 100191;北京航空航天大学宇航学院,北京 100191

发布日期:2021-08-15
作者简介:李家文(1972—),男,博士,副教授。研究领域为液体火箭发动机工作过程仿真。 E-mail:lijiawen@buaa.edu.cn

Combustion Efficiency Analysis on Vortex-Cooled Thrust Chamber

School of Astronautics, Beijing University of Aeronautics and Astronautics, Beijing 100191, China;School of Astronautics, Beijing University of Aeronautics and Astronautics, Beijing 100191, China;School of Astronautics, Beijing University of Aeronautics and Astronautics, Beijing 100191, China;School of Astronautics, Beijing University of Aeronautics and Astronautics, Beijing 100191, China

Published:2021-08-15

摘要/Abstract

摘要： 为了分析喷注器对涡流冷却推力室燃烧效率的影响,开展了2kN气氢/气氧涡流冷却推力室的设计、仿真与试验研究,设计加工了三种不同喷嘴分布直径的氢喷注面板,在试验过程中测量了推力、燃烧室圆筒段内壁面温度、内壁面压力等参数,利用热力计算、流场仿真与试验测量结果对涡流冷却推力室燃烧效率进行了分析。结果表明,在所分析的三种喷注面板中,喷嘴分布半径最大的推力室燃烧效率最高,为97.6%。同时开展了透明燃烧室的试验研究,高温火焰在燃烧室圆筒段59.5％半径以内区域,验证了内外涡流结构的存在。仿真结果表明,氢喷嘴分布直径影响燃烧区域的分布,从而影响燃烧效率。 

关键词: 液体火箭发动机;涡流冷却推力室;热试车;燃烧效率 

Abstract: To analyze the effects of injection design on chamber combustion efficiency,design, numerical simulation and testing were performed on the 2kN GH₂/GO_2vortex-cooled chamber. Three H_2injection plates with different distribution diameters were designed, and parameters, such as thrust, gas temperature near to the chamber wall, and chamber pressure, etc. were measured during the test. By utilizing thermodynamic calculation, CFD analysis and testing,efforts were made to analyze the chamber combustion efficiency. Results show that among the three analyzed injection plates, the chamber combustion efficiency reaches the highest of 97.6% when the injector distribution diameter is the largest. Hot-fire test on transparent chamber was also performed. Visualization of the combusting flow field indicates that flame is confined within the 59.5% radius inner region of the chamber. According to calculating results, the combustion efficiency is affected by the combustion region, which is impacted by the H_2injector distribution diameter.  

Key words: Liquid rocket engine; Vortex-cooled thrust chamber; Hot-fire test; Combustion efficiency

李家文,王化余,叶汉玉,俞南嘉. 涡流冷却推力室燃烧效率分析[J]. 推进技术, 2013, 34(11): 1507-1512.

LI Jia-wen, WANG Hua-yu, YE Han-yu, YU Nan-jia. Combustion Efficiency Analysis on Vortex-Cooled Thrust Chamber[J]. Journal of Propulsion Technology, 2013, 34(11): 1507-1512.

参考文献

[1] Vjas A B, Majdalani J,Chiaverini M J.The Bidirectional Vortex:Part 1-An Exact Inviscid Solution [R].AIAA 2003-5052.
[2] Vjas A B, Majdalani J, Chiaverini M J.The Bidirectional Vortex:Part 2-A Viscous Core Solution [R].AIAA 2003-5053.
[3] Anderson M, Rom C, Bonazza R,et al.Vortex Chamber Flow Field Characterization Using Laser Diagnostics[C].Las Vegas:52nd JANNAF propulsion meeting,2004.
[4] Chiaverini M J, Malecki M J.Vortex Combustion Chamber Development for Future Liquid Rocket Engine Applications[R].AIAA 2002-4149.
[5] Chiavertini M J, Malecki M J, Sauer A.Vortex Thrust Chamber Testing and Analysis for O₂-H₂Propulsion Applications[R].AIAA 2003-4473.
[6] Chiaverini M J, Sauer J A, Munson S M.Laboratory Characterization of Vortex-Cooled Thrust Chamber for Methane/O_2and H₂O₂[R].AIAA 2005-4131.
[7] Kargar M M, Mohammad H S.Experimental Investigation of Heat Transfer Modes in Vortex Combustion Engines [R].AIAA 2007-5586.
[8] Scott M Munson, J Arthur Sauer, Joshua D Rocholl,et al.Development of a Low-Cost Vortex-Cooled Thrust Chamber Using Hybrid Fabrication Techniques[R].AIAA 2011-5835.
[9] [苏]阿列玛索夫 B E.火箭发动机原理[M].张中钦,庄逢辰,等译.北京:宇航出版社,1993:228-232.
[10] Huu Trinh, Brad Bullard, Scott michaels.Evaluation of Impinging Stream Vortex Chamber Concepts for Liquid Rocket Engine Applications[R].AIAA 2003-4476.
[11] 唐飞, 李家文, 常克宇.涡流冷却推力室中涡流结构的分析与优化[J].推进技术, 2010,1(2).(TANG Fei, LI Jia-wen, CHANG Ke-yu.The Analysis and Optimization of Vortex Configuration for Vortex-Cooled Combustion Chamber [J].Journal of Propulsion Technology, 2010,1(2).)
[12] 吴东波, 李家文, 常克宇.GH₂/GO₂涡流冷却推力室设计与数值计算[J].火箭推进, 2010,6(5).
[13] 李家文, 唐飞, 俞南嘉.推力室涡流冷却技术试验研究[J].推进技术, 2012,3(6).(LI Jia-wen, TANG Fei, YU Nan-jia.Experimental Study on Vortex-Cooled Thrust Chamber [J].Journal of Propulsion Technology, 2012,3(6).)
[14] 朱子环,耿卫国,管理,等.某型号大推力火箭发动机试验推力测量不确定度评定[J].火箭推进,2012,10(5).
[15] 许维勤.涡喷发动机试车台架对发动机推力测量精度的影响[J].测控技术,1985(2).
[16] Gordon S, McBride B J.Computer Program for Calculation of Complex Chemical Equilibrium Compositions and Applications [R].NASA RP-1311,6.