推进技术 ›› 2013, Vol. 34 ›› Issue (4): 470-476.

• 气动热力学 • 上一篇    下一篇

高超声速风洞进气道流量系数测量精度影响因素研究

张绍武1,关祥东2,朱涛1,朱守梅2,3,邹琼芬1,曹程1   

  1. 中国空气动力研究与发展中心超高速所,四川 绵阳 621000;中国航天科工集团三十一研究所,北京 100074;中国空气动力研究与发展中心超高速所,四川 绵阳 621000;中国航天科工集团三十一研究所,北京 100074;中国空气动力研究与发展中心超高速所,四川 绵阳 621000;中国空气动力研究与发展中心超高速所,四川 绵阳 621000
  • 发布日期:2021-08-15
  • 作者简介:张绍武(1971—),男,硕士,高级工程师,研究领域为高超声速风洞实验技术。E-mail:zsw207172@sina.com

Investigation on Factors Affecting the Measurement Aceuracy for Inlet Flow Coefficient in Hypersonic Wind Tunnel

  1. Hypervelocity Research Institute of China Aerodynamics Research and Development Center, Mianyang 621000, China;The 31st Reaearch Institute of CASIC, Beijing 100074, China;Hypervelocity Research Institute of China Aerodynamics Research and Development Center, Mianyang 621000, China;The 31st Reaearch Institute of CASIC, Beijing 100074, China;Hypervelocity Research Institute of China Aerodynamics Research and Development Center, Mianyang 621000, China;Hypervelocity Research Institute of China Aerodynamics Research and Development Center, Mianyang 621000, China
  • Published:2021-08-15

摘要: 进气道是飞行器动力装置的重要组成部分,准确测量进气道流量系数是进气道风洞试验的重要内容。对来流马赫数Ma=4.5,5.0和6.0状态下皮托管进气道开展流量系数测量研究,通过对比理论值和实测值,获取各状态流量系数修正系数。试验结果表明,随着来流马赫数增加,进气道流量系数与理论值偏差较明显,并逐渐增大。超声速风洞试验通常认为测量截面总温与来流总温相等,通过对测量截面总温与来流总温偏差以及测量截面流场畸变情况的分析,判断测量偏差主要是由测量截面总温等于来流总温的假设导致的。在高超声速风洞试验中,由于模型壁面热交换的存在,测量截面总温低于来流总温,进气道流量系数测量时需要进行总温修正,以提高流量测量精度。 

关键词: 超声速进气道;高超声速风洞;试验;流量系数 

Abstract: Inlet is a critical component of aircraft propulsion system and accurate measurement of its flow coefficient is important in inlet wind tunnel experiments. Flow coefficient measurement investigations using Pitot tube inlet were carried out at free stream Mach number 4.5,5.0,6.0, respectively. Correction of flow coefficients in all kinds of cases were acquired by comparing the experimental values and theoretical values. The experimental results indicate that the difference compared with the theoretical values gradually rises up along with the increase in the incoming flow Mach number. According to the engineering experience in supersonic wind tunnel experiments, the temperature at measurement cross section is equal to the incoming flow total temperature. This hypothesis is also used in the current experiments. However, it is proved that this hypothesis is the main cause resulting in measurement bias by analyzing the deference between the two kinds of total temperature as mentioned above and the flow field distortion at measurement cross section. In hypersonic wind tunnel, the total temperature at measurement cross section is lower than that of the incoming flow because of the existence of heat transform on model wall surface. In order to increase the precision of the inlet flow coefficient measurement, the correction of total temperature is also required. 

Key words: Supersonic inlet;Hypersonic wind tunnel;Experiment; Flow coefficient