出流孔型对平板气膜冷却影响机理的研究

推进技术 ›› 2013, Vol. 34 ›› Issue (4): 499-505.

出流孔型对平板气膜冷却影响机理的研究

朱延鑫¹,谭晓茗¹,郭文²,张靖周¹

南京航空航天大学能源与动力学院, 江苏南京 210016;南京航空航天大学能源与动力学院, 江苏南京 210016;中国燃气涡轮研究院,四川成都 610500;南京航空航天大学能源与动力学院, 江苏南京 210016

发布日期:2021-08-15
作者简介:朱延鑫(1988—),硕士生,研究领域为传热传质。 E-mail:zyx@nuaa.edu.cn
基金资助:
国家自然科学基金(50876041)；南京航空航天大学基本科研业务费专项科研项目(NS2010045)。

Numerical Simulation on Effects of Different Film Cooling Holes on Plate

College of Energy and Power Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China;College of Energy and Power Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China;China Gas Turbine Establishment,Chengdu 610500,China;College of Energy and Power Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China

Published:2021-08-15

摘要/Abstract

摘要： 为了研究不同孔型对平板气膜冷却的影响,针对圆形,扇形,水滴形,收敛缝形四种气膜出流孔型的流动和传热特性进行了数值模拟。研究结果表明,圆形孔、扇形孔和水滴形孔气膜出口下游出现从中心向上抬升的反向旋转涡对,将主流燃气卷吸进来；收敛缝形孔在侧向的扩张型面使得气膜出流在展向的覆盖更为均匀,这有效地阻止了高温气体的侵入；在相同吹风比下,收敛缝形孔在气膜出口附近区域的平均绝热冷却效率则明显要高于其余三种孔,随着吹风比的增大,这种差距越发明显；孔型对对流换热系数增强比的影响区域仅局限在邻近气膜孔出口大约7倍气膜孔径的范围内。 

关键词: 气膜冷却;数值模拟;水滴形孔;收敛缝形孔; 扇形孔 

Abstract: Numerical simulation was carried out to study the flow and heat transfer characteristics of film cooling on flat plate with different hole shapes including circle, fan, water-drop and converging slot. The results show that the counter-rotating vortex pair lifting up from the center have appeared in the outlet of film with circle-shaped, fan-shaped water-drop shaped hole, which will revolve the mainstream gas flow into the film coolant. Film from converging slot shows different flow characteristics.The slot with a spanwise expansion makes film spreading widely on the wall which effectively prevents the invasion of hot gas. Under the same blowing ratio, the cooling effectiveness of the converging slot hole is significantly better than the other three holes. With increasing blowing ratio, this advantage of the converging slot is more obvious.The impact of hole shape on heat transfer enhancement ratio is limited in the range of 7times of film hole diameter away from the outlet. 

Key words: Film cooling；Numerical simulation；Water-drop shape hole；Converging slot hole；Fan hole

朱延鑫,谭晓茗,郭文,张靖周. 出流孔型对平板气膜冷却影响机理的研究[J]. 推进技术, 2013, 34(4): 499-505.

ZHU Yan-xin¹, TAN Xiao-ming¹,GUO Wen²,ZHANG Jing-zhou¹. Numerical Simulation on Effects of Different Film Cooling Holes on Plate[J]. Journal of Propulsion Technology, 2013, 34(4): 499-505.

参考文献

[1] 葛绍岩,徐靖中．气膜冷却[M]．北京:科学出版社,1985.
[2] Bittlinger G,Schulz A,Wittig S.Film Cooling Effectiveness and Heat Transfer Coefficients for Slot Injection at High Blowing Ratios[R].ASME 94-GT-182.
[3] Farmer J P,Seager D J,Liburdy J A.The Effect of Shaping Inclined Slots on Film Cooling Effectiveness and Heat Transfer Coefficient[R].ASME 97-GT-399.
[4] 徐红洲,苏红桢,刘松龄,等.倾斜30°锥形喷孔气膜冷却的流动和传热实验研究[J].推进技术,1996,17(5):52-58.(XU Hong-zhou;SU Hong-zhen;LIU Song-ling,et al.An Experimental Study on Flow and Heat Transfer Around a Single Cone-Shaped Film Cooling Hole with Inclined Angle of 30°[J].Journal of Propulsion Technology,1996,17(5): 52-58.)
[5] Hasan Nasir,Sumanta Acharya,Srinath Ekkad.Improved Film Cooling from Cylindrical Angled Holes with Triangular Tabs:Effect of Tab Orientations[J].International Journal of Heat and Fluid Flow,2003,24:657-668.
[6] Hasan Nasir,Sumanta Acharya,Srinath Ekkad.Film Cooling from a Single Row of Cylindrical Angled Holes with Triangular Tabs Having Different Orientations[R].ASME 2001-GT-0124.
[7] Sargison J E,Guo S M,Oldfield M L G,et al.A Converging Slot-Hole Film-Cooling Geometry Part 1:Low-Speed Flat-Plate Heat Transfer and Loss[R].ASME 2001-GT-0126.
[8] Sargison J E,Guo S M,Oldfield M L G,et al.A Converging Slot-Hole Film-Cooling Geometry Part 2:Transonic Nozzle Guide Vane Heat Transfer and Loss[R].ASME 2001-GT-0127.
[9] Hyung Hee Cho,Dong Ho Rhee,Byung Gi Kim.Enhancement of Film Cooling Performance Using a Shaped Film Cooling Hole with Compound Angle Injection[J].JSME International Journal,Series B (Fluids and Thermal Engineering),2001,44(1):99-110.
[10] Dittmar J,Schulz A,Wittig S.Assessment of Various Film-Cooling Configurations Including Shaped and Compound Angle Holes Based on Large-Scale Experiments[J].ASME Journal of Turbomachinary,2003,125(1):57-64.
[11] Mayhew James E,Baughn James W,Byerley Aaron R.The Effect of Freestream Turbulence on Film Cooling Heat Transfer Coefficient and Adiabatic Effectiveness Using Compound Angle Holes[J].ASME Journal of Heat Transfer,2004,3:201-212.
[12] Yuen C H N,Martinez-Botas R F,Whitelaw J H.Film Cooling Effectiveness Downstream of Compound and Fan- Shaped Holes[R].ASME 2001-GT-1031.
[13] Yu Y,Yen C H,Shih T I P,et al.Film Cooling Effectiveness and Heat Transfer Coefficient Distributions Around Diffusion Shaped Holes[J].ASME Journal of Heat Transfer,2002,124(5):820-827.
[14] 李少华,宋东辉,刘建红,等.不同孔型平板气膜冷却的数值模拟[J].中国电机工程学报,2006,26(17):112-116.
[15] 郭婷婷,刘建红,宋东辉,等.不同形状气膜孔对气膜冷却效果的影响[J].动力工程,2006,26(3):333-336.
[16] 刘江涛,吴海玲,陶涛,等.斜孔气膜冷却数值模拟分析[J].工程热物理学报,2004,25(6):1034-1036.