发动机燃烧室内壁材料热环境的气动热试验模拟技术研究

推进技术 ›› 2013, Vol. 34 ›› Issue (4): 512-519.

发动机燃烧室内壁材料热环境的气动热试验模拟技术研究

涂建强¹,陈连忠¹,王琴²,马雪松²,焦廷友²,陈峰¹

中国航天空气动力技术研究院,北京 100074;中国航天空气动力技术研究院,北京 100074;中国航天科工集团三十一研究所高超声速冲压发动机技术重点实验室,北京 100074;中国航天科工集团三十一研究所高超声速冲压发动机技术重点实验室,北京 100074;中国航天科工集团三十一研究所高超声速冲压发动机技术重点实验室,北京 100074;中国航天空气动力技术研究院,北京 100074

发布日期:2021-08-15
作者简介:涂建强(1982—),男,硕士,工程师,研究领域为高超声速飞行器热防护地面试验技术研究。 E-mail:tujianqiang@gmail.com

Investigation on Aerothermodynamic Simulation Technology for Thermal Environment of Engine Combustor Inner Surface Material

China Academy of Aerospace Aerodynamics, Beijing 100074, China;China Academy of Aerospace Aerodynamics, Beijing 100074, China;Science and Technology on Scramjet Laboratory,The 31st Research Institute of CASIC, Beijing 100074, China;Science and Technology on Scramjet Laboratory,The 31st Research Institute of CASIC, Beijing 100074, China;Science and Technology on Scramjet Laboratory,The 31st Research Institute of CASIC, Beijing 100074, China;China Academy of Aerospace Aerodynamics, Beijing 100074, China

Published:2021-08-15

摘要/Abstract

摘要： 利用超声速矩形湍流导管和等离子电弧加热器模拟了发动机燃烧室内流和高超声速飞行器外壁面外流热环境,进行了平板表面冷壁热流测量和燃烧室内壁材料考核试验。结果表明:由于辐射换热的影响,在选取的两个典型来流条件下,发动机燃烧室内流热环境下的冷壁热流比外流热环境下的高出21%和40%,但是冷壁热流的增量基本相当,约为0.70~0.80MW/m²。随着冷壁热流的增加,辐射换热产生的热流增量的影响力会逐渐减小。材料考核时,相同配方的C/SiC复合材料在内流热环境下的表面温度高出约400℃,背面温度高出约90℃,这种差异对于发动机燃烧室内壁面材料考核至关重要,必须在材料考核试验中加以考虑。 

关键词: 发动机燃烧室;内流热环境;外流热环境;湍流导管;电弧加热器 

Abstract: The inner flow and outer flow thermal environment has usually taken place in the inner surface of engine combustor and the outer surface of hypersonic vehicle, respectively. The two kinds of thermal environment have been compared by using the supersonic rectangle turbulent flow duct and arc heater. The cold-wall heat flux was measured and the engine combustor inner surface material was tested in two kinds of thermal environment. Due to the effect of thermal radiation heat transfer, the cold-wall heat flux of inner flow is respectively 21% and 40% higher than that of outer flow in two kinds of representative flow conditions. And the increments of the cold-wall heat fluxes are nearly equal, about 0.70~0.80MW/m². So when the cold-wall heat flux increases, the effect of radiation heat transfer will gradually decrease. In material test experiment, the surface and rear temperature of the C/SiC composites in the inner flow is respectively higher about 400℃ and 90℃ than those with same formulation design in the outer flow, which is very significant to test the engine combustor inner surface material and must be considered in the material test experiment. 

Key words: Engine combustor; Inner flow thermal environment; Outer flow thermal environment; Turbulent duct; Arc heater

涂建强,陈连忠,王琴,马雪松,焦廷友,陈峰. 发动机燃烧室内壁材料热环境的气动热试验模拟技术研究[J]. 推进技术, 2013, 34(4): 512-519.

TU Jian-qiang¹, CHEN Lian-zhong¹, WANG Qin², MA Xue-song², JIAO Ting-you², CHEN Feng¹. Investigation on Aerothermodynamic Simulation Technology for Thermal Environment of Engine Combustor Inner Surface Material[J]. Journal of Propulsion Technology, 2013, 34(4): 512-519.

参考文献

[1] Milos F S, Scott C D, Steven V D.Arcjet Testing and Thermal Model Development for Multilayer Felt Reusable Surface Insulation[R].AIAA 2012-2869.
[2] Sara D B, Marco M, Giuseppe C R, et al.Aerothermodynamic Analysis of the EXPERT Winglet:from the In-flight Environment Characterization to the Rebuilding of the Scirocco Plasma Wind Tunnel test[R].AIAA 2009-7242.
[3] Roberto G, Antonio D V, Giuliano M, et al.CIRA Activities on UHTC’s:on-Ground and in Flight Experimentations[R].AIAA 2011-2303.
[4] Painter J H, Schaeffer J F.Performance Characteristics of a Huels-Type Arc Heater Operating on Hydrogen, Helium, or Air[R].AEDC TR-76-25.
[5] Siva R, Krishnendu S.Analysis of High-enthalpy Air-chemistry and its Effect on Stagnation Point Heat Flux[R].AIAA 2012-3002.
[6] Wolfgang P P, Fisch W, Bolz J.ULTIMATE:Metallic TPS for Futrue RLV’s-First Result of Ground & Flight Test Campaigns[R].AIAA 2006-2950.
[7] Steven A S, Robert S K, Chris A R.Testing of SLA-561V in NASA-Ames’ Turbulent Flow Duct with Augmented Radiative Heating[R].AIAA 2011-3619.
[8] Beachler J C, Kachel W A.A Shrouded Flow Arc Air Heater for Simulation of a 250Megawatt Plasma Jet Heater[R].NASA 74-10262.
[9] Painter J H.High Pressure Arc Heater Test Stream Enlargement Using Shrouded Flow[R].AIAA 81-1148.
[10] Anderson J D.Hypersonic and High Temperature Gas Dynamics[M].New York:McGraw-Hill Book Company, 2006:501-558.
[11] Murty V D.Nonlinear Internal Flow Analysis[R].ASIAC TR-97-02.
[12] Tsien H S.Similarity Laws of Hypersonic Flows[J].Journal of Mathematics and Physics,1946,5:247-251.
[13] Peterson A B, Nichols F, Mifsud B.Arc Jet Testing in NASA Ames Research Center Thermophysics Facilities[R].AIAA 92-5041.
[14] ASTM International Designation:E 457-96(Reapproved 2002), Standard Test Method for Measuring Heat-Transfer Rate Using a Thermal Capacitance (slug) Calorimeter[S].USA:American Society for Testing Materials (ASTM).Annual Book of ASTM Standards.
[15] Robert S, John R H.Thermal Radiation Heat Transfer[M].New York:Taylor & Francis,2002:191-217.
[16] Touloukian Y S.Thermo-Physical Properties of High Temperature Solid Material[D].Purdue:Purdue University, 1966.
[17] Davide A, Luigi S, Stefania C, et al.Emissivity and Catalycity Measurements on SiC-coated Carbon Fiber Reinforced Silicon Carbide Composite[J].Journal of the European Ceramic Society, 2009,9(10):2045-2051.