单边膨胀尾喷管下壁面型线优化设计及实验研究 *

推进技术 ›› 2014, Vol. 35 ›› Issue (10): 1297-1302.

• 气动热力学　总体 • 下一篇

单边膨胀尾喷管下壁面型线优化设计及实验研究 *

庞丽娜,徐惊雷,范志鹏

江苏省航空动力系统重点实验室南京航空航天大学能源与动力学院，江苏南京 210016;江苏省航空动力系统重点实验室南京航空航天大学能源与动力学院，江苏南京 210016;江苏省航空动力系统重点实验室南京航空航天大学能源与动力学院，江苏南京 210016

发布日期:2021-08-15
作者简介:庞丽娜(1988—)，女，硕士生，研究领域为高超声速进排气动力学。
基金资助:
国家自然科学基金(90916023)。

Optimization Design and Experimental Study of Cowl Configuration of SERN

Jiangsu Province Key Laboratory of Aerospace Power Systems，Nanjing University of Aeronautics and Astronautics，Nanjing 210016，China;Jiangsu Province Key Laboratory of Aerospace Power Systems，Nanjing University of Aeronautics and Astronautics，Nanjing 210016，China;Jiangsu Province Key Laboratory of Aerospace Power Systems，Nanjing University of Aeronautics and Astronautics，Nanjing 210016，China

Published:2021-08-15

摘要/Abstract

摘要： 基于Isight优化平台，将多目标遗传算法与CFD计算相结合，针对超燃冲压发动机非对称尾喷管冷/热态俯仰力矩差较大的问题，对下壁面为三次曲线的尾喷管构型进行多目标优化，分析了初始膨胀角和尾缘角的相互耦合及其对喷管性能影响所占比重。结果表明，设计区间内，下壁面三次曲线构型在保持较高推力特性的前提下，可以大范围调整喷管俯仰力矩，显著改善喷管冷/热态俯仰力矩差较大的问题。在此基础上，选取优化所得点进行冷流缩比风洞实验，根据实验条件进行了相应的数值模拟，对比发现数值模拟与实验结果吻合很好，验证了该优化设计方法及结果的有效性和可靠性。

关键词: 单膨胀斜面喷管；优化设计；几何参数；俯仰力矩差；风洞实验

Abstract: In order to decrease the difference of cold/hot pitching moment，an optimization design method based on the Isight software，and integrated by using CFD and Non-dominated Sorting Genetic Algorithm(NSGAⅡ)，is applied to design for a cubic curve cowl of SERN. Then the interaction with the major geometric parameters (initial expansion angle and terminal angle) and their effects on the SERN performance are further investigated. The results show that，within the design range，the cubic curve cowl can ensure the SERN keep high thrust coefficient，and adjust the pitch moment within a wide range，change the difference of nozzle cold/hot pitch moment greatly at the same time. Finally a cold flow wind tunnel experiment of scaled model is carried out，and a numerical simulation is performed based on the conditions of the tunnel test. The results of the simulation are in good agreement with experiment data，which validates the effectiveness and correctness of the optimization method and the results of numerical simulation.

Key words: Single expansion ramp nozzle；Optimization design；Geometric parameters；Difference of pitch moment；Wind tunnel test

庞丽娜,徐惊雷,范志鹏. 单边膨胀尾喷管下壁面型线优化设计及实验研究 *[J]. 推进技术, 2014, 35(10): 1297-1302.

PANG Li-na,XU Jing-lei,FAN Zhi-peng. Optimization Design and Experimental Study of Cowl Configuration of SERN[J]. Journal of Propulsion Technology, 2014, 35(10): 1297-1302.

参考文献

[1] Eric Gamble, Dan Haid. Improving off Design Nozzle Performance Using Fluidic Injection [R]. AIAA 2004-1206.
[2] 张留欢, 徐惊雷, 莫建伟. 二元非对称喷管可调方案试验研究 [J]. 航空学报, 2013, 34(4): 772-778.
[3] 徐惊雷, 张艳慧, 张堃元. 超燃冲压发动机非对称喷管非设计状态性能计算[J]. 推进技术, 2007, 28(3): 287-290.(XU Jing-lei, ZHANG Yan-hui, ZHANG Kun-yuan. Numerical Simulation of Single Expansion Ramp Nozzle for Scramjet on the Off-Design Point [J].Journal of Propulsion Technology, 2007, 28(3): 287-290.)
[4] Marathe A G, Thiagarajan V. Effect of Geometric Parameters on the Performance of Single Expansion Ramp Nozzle[R]. AIAA 2005-4429.
[5] Damira S K, Marathe A G, Sudhakar K. Parametric Optimization of Single Expansion Ramp Nozzle (SERN) [R]. AIAA 2006-5188.
[6] Gao T Y, Cui K, Wang X P, et al. Aerodynamic Optimization and Evaluation for the Three-Dimensional Afterbody/Nozzle Integrated Configuration of Hypersonic Vehicles [J].Chinese Science Bulletin, 2012, 57(4): 239-247.
[7] 黄伟, 罗世彬, 王振国. 超燃冲压发动机尾喷管构型参数灵敏度分析 [J]. 推进技术, 2009, 30(6): 691-695.(HUANG Wei, LUO Shi-bin, WANG Zhen-guo. Parametric Sensitivity Analysis of Scramjet Nozzle Configuration [J].Journal of Propulsion Technology, 2009, 30(6): 691-695.)
[8] 贺旭照, 张勇, 汪广元. 高超声速飞行器单壁膨胀喷管的自动优化设计 [J]. 推进技术, 2007, 28(2): 148-151.(He X Z, Zhang Y, Wang G Y. Automated Design Optimization of Single Expansion Ramp Nozzle for Hypersonic Vehicle [J].Journal of Propulsion Technology, 2007,28(2): 148-151.)
[9] 陈兵, 徐旭, 蔡国飙. 基于遗传算法和空间推进方法的单臂扩张喷管优化设计研究 [J]. 航空学报, 2007, 28(4): 827-832.
[10] 张艳慧. 非对称大膨胀比喷管设计及性能分析 [D]. 南京: 南京航空航天大学, 2006.
[11] Goeing M. Nozzle Design Optimization by Method-of-Characteristics [R]. AIAA 90-2024.
[12] Mo J W, Xu J L, Zhang L H. The Experimental and Numerical Study of the Over-Under TBCC Exhaust System[R].AIAA 2011-2234.
[13] SrinivasN, Deb K. Multi-objective Function Optimization Using Non-dominated Sorting Genetic Algorithms [J]. Evolutionary Computation, 1995, 2(3): 221-248.
[14] DebK, Pratap A, Agarwal S, etal. A Fast and Elitist Multi-objective Genetic Algorithm NSGA-II [J]. IEEE Transactions on Evolutionary Computation, 2002, 6(2):182-197.
[15] 范志鹏, 徐惊雷, 莫建伟.几何约束下SERN喷管优化设计 [C]. 哈尔滨: 中国力学学会, 2011.
[16] 邹林君, 吴义忠, 毛虎平. Kriging模型的增量构造及其在全局优化中的应用 [J]. 计算机辅助设计与图形学学报, 2011, 23(4): 649-655.
[17] 葛建辉, 徐惊雷, 王明涛. 非对称喷管流动分离的预测[J]. 航空学报, 2012, 38(8): 1394-1399.(编辑:史亚红)　收稿日期:2013-10-14；修订日期:2013-11-26。基金项目:国家自然科学基金(90916023)。作者简介:庞丽娜(1988—),女,硕士生,研究领域为高超声速进排气动力学。E-mail:pln1989@foxmail.com

单边膨胀尾喷管下壁面型线优化设计及实验研究 *

Optimization Design and Experimental Study of Cowl Configuration of SERN

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 0

编辑推荐

Metrics

本文评价