带分流叶片离心压气机优化设计

推进技术 ›› 2014, Vol. 35 ›› Issue (11): 1461-1468.

带分流叶片离心压气机优化设计

刘　波,杨晰琼,曹志远,张　鹏

西北工业大学动力与能源学院，陕西西安 710072;西北工业大学动力与能源学院，陕西西安 710072;西北工业大学动力与能源学院，陕西西安 710072;西北工业大学动力与能源学院，陕西西安 710072

发布日期:2021-08-15
作者简介:刘　波(1960—)，男，博士，教授，博士生导师，研究领域为先进叶轮机械气动设计及试验。
基金资助:
国家自然科学基金(51236006)。

Optimization Design of a Centrifugal Compressor with Splitters

School of Power and Energy，Northwestern Polytechnical University，Xi’an 710072，China;School of Power and Energy，Northwestern Polytechnical University，Xi’an 710072，China;School of Power and Energy，Northwestern Polytechnical University，Xi’an 710072，China;School of Power and Energy，Northwestern Polytechnical University，Xi’an 710072，China

Published:2021-08-15

摘要/Abstract

摘要： 为探索带分流叶片离心压气机的优化方法，进一步提高气动性能，建立带分流叶片离心压气机优化系统:运用Bézier函数建立叶型的参数化表征方法，并采用人工神经网络建立目标函数和几何优化变量间的对应关系，结合遗传算法求解优化命题。为验证系统可行性，以极大化等熵效率为优化目标，针对带分流叶片的离心压气机进行优化设计。结果表明:该优化系统明显提高带分流叶片离心压气机的气动性能，优化后设计点等熵效率提高3.68%，压比提高0.506，设计转速下全工况范围内效率明显提升，综合稳定裕度增大；优化后90%，50%叶高波前马赫数有明显降低，前缘激波有所减弱，激波与附面层相互作用引起的损失减小，二次流得到抑制，叶尖通道内大范围低速区明显消退；叶片载荷重新分配，分流叶片载荷一部分转移至主叶片。

关键词: 离心压气机；分流叶片；优化系统；参数化法；气动优化

Abstract: In order to explore the method of optimization and improve the performance of centrifugal compressor with splitters，an optimization system is developed. Bézier curves are used to realize parametric representation and approximate function between geometry parameters and aerodynamic performance is established by artificial neural network. The process of optimization is realized by genetic algorithm optimization together with numerical calculation. To verify the feasibility of the system，a compressor with splitters is optimized to achieve maximum isentropic efficiency. It is significant that the isentropic efficiency increases by 3.68% and the pressure ratio increases by 0.506 at the optimization point. The efficiency increases significantly at all operating conditions at design speed with an expansion of the surge margin. Numerical simulation shows that the relative Mach number at leading edge decreases at 90% span and 50% span，and the loss caused by intersection of shock and boundary layer is reduced. Furthermore，the secondary flow is inhibited and the low-speed area is largely reduced. In addition，the load of the blades is redistributed and part of the load is transferred from the splitters to the main blades.

Key words: Centrifugal compressor；Splitter；Optimization system；Parameterization；Aerodynamic optimization

刘　波,杨晰琼,曹志远,张　鹏. 带分流叶片离心压气机优化设计[J]. 推进技术, 2014, 35(11): 1461-1468.

LIU Bo,YANG Xi-qiong,CAO Zhi-yuan,ZHANG Peng. Optimization Design of a Centrifugal Compressor with Splitters[J]. Journal of Propulsion Technology, 2014, 35(11): 1461-1468.

参考文献

[1] Krain H. Review of Centrifugal Compressor’s Application and Development[R]. ASME 2003-GT-38971.
[2] Marconcini M, Rubechini F, Arnone A. Numerical Investigation of a High Speed Centrifugal Compressor Impeller [R]. ASME 2006-GT-90098.
[3] Kang S. Numerical Investigation of a Transonic Centrifugal Compressor[R]. ASME 2005-GT-68092.
[4] Abdus Samad. Stacking and Thickness Optimization of a Compressor Blade using Weighted Average Surrogate Model[R].ASME 2008-GT -50262.
[5] Xiaomin Liu, Wenbin Zhang. Two Schemes of Multi-objective Aerodynamic Optimization for Centrifugal Impeller Using Response Surface Model and Genetic Algorithm[R]. ASME 2010-GT-23775.
[6] 赵晶, 唐焕文, 朱训芝. 模拟退火算法的一种改进及其应用研究[J]. 大连理工大学学报, 2006, 16(5).
[7] 张朝磊, 樊未军, 丰镇平. 级环境下离心压气机扩压器叶片气动优化设计[J].西安交通大学学报, 2009, 43(11).
[8] Hildebrandt A. Aerodynamic Optimization of a Centrifugal Compressor Return Channel and U-Turn With Genetic Algorithms[R]. ASME 2011-GT-45076.
[9] Andreas Bartold, Franz Joos. Optimization of a Centrifugal Impeller Using Evolutionary Algorithms[R]. ASME 2008-GT-50805.
[10] 周荐辉, 樊未军, 田晓沛, 等. 某小型高速离心叶轮的优化设计[J].航空动力学报, 2009, 24(09).
[11] 何坤, 陈志鹏, 袁新. 离心压气机叶片三维气动优化设计[J].工程热物理学报, 2009, 30(03).
[12] Akay A Islek. Optimization of Micro Compressor Blades Using CFD Analysis and Artificial Intelligence[C]. Honolulu: Proceedings of the ASME/JSME Joint Fluids Engineering Conference, 2003.
[13] 施法中.计算机辅助几何设计与非均匀有理样条[M]. 北京:高等教育出版社, 2001.
[14] Cichocki A, Unbehauen R.Neural Networks for Optimization and Signal Processing [M].NewYork:Wiley and Sons Press, 1993.
[15] Mengistu T, Ghaly W. Single and Multipoint Shape Optimization of Gas Turbine Blade Cascades [R]. AIAA 2004-4446.
[16] Dominique S, Trépanier J Y. Optimization of a Gas Turbo Engine Rotor Disc Using Case-Based Reasoning and the Gate Genetic Algorithm[R]. ASME 2010-GT-23011.
[17] 李雪松, 杜建一, 祁志国, 等. 两个高比转速离心压气机模型级的设计分析[J].流体机械, 2005, 33(5).
[18] 邱智凌, 郑新前, 张扬军. 车载燃料电池低比转速离心压气机设计[J].清华大学学报, 2008, 48(5).(编辑:梅瑛)　　　　　　　　　　　　　　收稿日期:2013-11-03；修订日期:2013-12-26。基金项目:国家自然科学基金(51236006)。作者简介:刘波(1960—),男,博士,教授,博士生导师,研究领域为先进叶轮机械气动设计及试验。E-mail:liubo704@nwpu.edu.cn