肋开孔高度对大宽高比矩形通道流动传热的影响 *

推进技术 ›› 2014, Vol. 35 ›› Issue (12): 1630-1638.

肋开孔高度对大宽高比矩形通道流动传热的影响 *

朱强华,崔　苗,高效伟

大连理工大学航空航天学院工业装备结构分析国家重点实验室，辽宁大连 116024,大连理工大学航空航天学院工业装备结构分析国家重点实验室，辽宁大连 116024,大连理工大学航空航天学院工业装备结构分析国家重点实验室，辽宁大连 116024

发布日期:2021-08-15
作者简介:朱强华(1980—)，男，博士，讲师，研究领域为叶轮机气动热力学。
基金资助:
国家自然科学基金(51206014)；中央高校基本科研业务费专项资助(DUT2012054 )。

Effects of Holes Height on Flow and Heat Transfer in a Ribbed Rectangular Channel with Large Aspect Ratio

State Key Laboratory of Structural Analysis for Industrial Equipment，School of Aeronautics and Astronautics，Dalian University of Technology，Dalian 116024，China,State Key Laboratory of Structural Analysis for Industrial Equipment，School of Aeronautics and Astronautics，Dalian University of Technology，Dalian 116024，China and State Key Laboratory of Structural Analysis for Industrial Equipment，School of Aeronautics and Astronautics，Dalian University of Technology，Dalian 116024，China

Published:2021-08-15

摘要/Abstract

摘要： 为了获得大宽高比矩形通道内开孔肋的流动与传热特性，采用数值模拟的方法在开孔肋的肋高e/Dh=0.188、开孔率β=0.131时研究了通道的摩擦系数、努塞尔数等参数随孔排高度和雷诺数的变化规律。结果表明:与实体肋相比，开孔肋能够减小通道的摩擦系数并提高其壁面温度分布的均匀性，但是传热增强因子有所减小；随着孔排高度的提升，通道的摩擦系数单调减小，壁面温度分布的不均匀度增大，而传热增强因子则先增大后减小，因此存在一最优孔排高度(h/e)opt=0.65使开孔肋的强化传热综合指标达到最大值；随着雷诺数的增大，开孔肋通道的摩擦系数缓慢减小、换热逐渐增强，这与实体肋的变化规律是类似的。

关键词: 燃气轮机；矩形通道；实体肋；开孔肋；强化传热

Abstract: Numerical study of flow and heat transfer characteristics in a large aspect ratio rectangular channel with a perforated rib mounted on the bottom surface were performed for the rib height-to-channel hydraulic diameter (e/Dh) and the open area ratio (β) fixed at 0.188 and 0.131 respectively. The effects of non-dimensional holes height (h/e) and entrance flow Reynolds number on the friction factor and Nusselt number of channel were analyzed. The results show that the perforated rib has a lower friction factor and more uniform surface temperature distribution as compared with the solid rib，but its averaged Nusselt number ratio slightly drops. As the holes height elevating，both the friction factor and the temperature field uniformity decrease gradually，while the averaged Nusselt number ratio take on the up-down tendency，so there is an optimal holes height (h/e)opt=0.65 for the thermal performance factor reached its maximum. Similarly to the solid rib，the friction factor slowly decreases and the averaged Nusselt number monotonic increases with the increasing of Reynolds number for the perforated rib.

Key words: Gas turbine；Rectangular channel；Solid rib；Perforated rib；Enhanced heat transfer

朱强华,崔　苗,高效伟. 肋开孔高度对大宽高比矩形通道流动传热的影响 *[J]. 推进技术, 2014, 35(12): 1630-1638.

ZHU Qiang-hua,CUI Miao,GAO Xiao-wei. Effects of Holes Height on Flow and Heat Transfer in a Ribbed Rectangular Channel with Large Aspect Ratio[J]. Journal of Propulsion Technology, 2014, 35(12): 1630-1638.

参考文献

[1] Han J C, Dutta S, Ekkad S. Gas Turbine Heat Transfer and Cooling Technology (2nd Edition) [M]. USA: CRC Press, Taylor & Francis Group, 2013.
[2] 曹玉璋. 航空发动机传热学[M]. 北京: 北京航空航天大学出版社, 2005.
[3] Smulsky Y I, Terekhov V I, Yarygina N I. Heat Transfer in Turbulent Separated Flow Behind a Rib on the Surface of Square Channel[J]. International Journal of Heat and Mass Transfer, 2012, 55(4): 726-733.
[4] Kamali R, Binesh A R. The Importance of Rib Shape Effects on the Local Heat Transfer and Flow Friction Characteristics of Square Ducts with Ribbed Internal Surfaces[J]. International Communications in Heat and Mass Transfer, 2008, 35(8): 1032-1040.
[5] Promvonge P, Thianpong C. Thermal Performance Assessment of Turbulent Channel Flows Over Different Shaped Ribs[J]. International Communications in Heat and Mass Transfer, 2008, 35(10): 1327-1334.
[6] Liou T M, Yang C P, Lee H L. LDV Measurements of Spatially Periodic Flows over a Detached Solid-Rib Array[J]. Journal of Fluids Engineering, 1997, 119(2): 383-389.
[7] Ahn J, Lee J S. Large Eddy Simulation of Flow and Heat Transfer in a Channel with a Detached Rib Array[J]. International Journal of Heat and Mass Transfer, 2010, 53(1-3): 445-452.
[8] Changcharoen W, Eiamsa-ard S. Numerical Investigation of Turbulent Heat Transfer in Channels with Detached Rib-Arrays[J]. Heat Transfer-Asian Research, 2011, 40(5): 431-447.
[9] Hwang J J, Liou T M. Heat Transfer Augmentation in a Rectangular Channel with Slit Rib-Turbulators on Two Opposite Walls[J]. Journal of Turbomachinery, 1997, 119(3): 617-623.
[10] Liou T M, Kao C W, Chen S H. Flowfield Investigation of the Effect of Rib Open Area Ratio in a Rectangular Duct[J]. Journal of Fluids Engineering, 1998, 120(3): 504-512.
[11] Panigrahi P K, Schr?der A, Kompenhans J. PIV Investigation of Flow Behind Surface Mounted Permeable Ribs[J]. Experiments in Fluids, 2006, 40(2): 277-300.
[12] Shin S, Kwak J S. Effect of Hole Shape on the Heat Transfer in a Rectangular Duct with Perforated Blockage Walls[J]. Journal of Mechanical Science and Technology, 2008, 22(10): 1945-1951.
[13] Huang K D, Tzeng S C, Jeng T M, et al. Experimental Study of Fluid Flow and Heat Transfer Characteristics in the Square Channel with a Perforation Baffle[J]. International Communications in Heat and Mass Transfer, 2008, 35(9): 1106-1112.
[14] Sundén B. Convective Heat Transfer and Fluid Flow Physics in Some Ribbed Ducts Using Liquid Crystal Thermography and PIV Measuring Techniques[J]. Heat and Mass Transfer, 2011, 47(8): 899-910.
[15] Nuntadusit C, Wae-hayee M, Bunyajitradulya A, et al. Thermal Visualization on Surface with Transverse Perforated Ribs[J]. International Communications in Heat and Mass Transfer, 2012, 39(5): 634-639.
[16] Gajusingh S T, Shaikh N, Siddiqui K. Influence of a Rectangular Baffle on the Downstream Flow Structure[J]. Experimental Thermal and Fluid Science, 2010, 34(5): 590-602.
[17] Ghorbani-Tari Z, Sundén B, Tanda G. Experimental Study of Convection Heat Transfer in the Entrance Region of a Rectangular Duct with Transverse Ribs[R]. ASME HT-2012-58178.(编辑:史亚红)　　　　　　　　　　　　　*　收稿日期:2013-11-05；修订日期:2013-12-20。基金项目:国家自然科学基金(51206014)；中央高校基本科研业务费专项资助(DUT2012054 )。作者简介:朱强华(1980—),男,博士,讲师,研究领域为叶轮机气动热力学。E-mail:qhzhu@dlut.edu.cn