横流马赫数对溢流孔附近流动及换热的影响 *

推进技术 ›› 2014, Vol. 35 ›› Issue (12): 1645-1652.

横流马赫数对溢流孔附近流动及换热的影响 *

苏文超,朱惠人,聂建豪

西北工业大学动力与能源学院，陕西西安 710072,西北工业大学动力与能源学院，陕西西安 710072,西北工业大学动力与能源学院，陕西西安 710072

发布日期:2021-08-15
作者简介:苏文超(1989—)，男，硕士生，研究领域为航空发动机高温部件的传热与冷却技术。
基金资助:
国家重点基础研发发展计划(2013CB035702)。

Effects of Cross-Flow Mach Number on Flow and Heat Transfer Characteristics Around Effusion Hole

School of Power and Energy，Northwestern Polytechnical University，Xi’an 710072，China,School of Power and Energy，Northwestern Polytechnical University，Xi’an 710072，China and School of Power and Energy，Northwestern Polytechnical University，Xi’an 710072，China

Published:2021-08-15

摘要/Abstract

摘要： 为了研究冷气通道横流马赫数变化时溢流孔附近流动和换热情况，选取光滑冷却通道、90°溢流孔冷却通道和45°溢流孔冷却通道作为研究对象，保持入口雷诺数为8×104，在横流比分别为0.5和1的情况下，对横流马赫数为0.2和0.7时溢流孔附近流动及换热特性进行数值模拟。研究发现:在相同入口雷诺数和横流比条件下，横流马赫数由0.2增大为0.7时，溢流孔内的回流范围减小，孔内流动阻力变小，冷却通道壁面换热减弱。当横流比变化时，低横流比情况下横流马赫数对冷却通道壁面换热影响要更大。

关键词: 涡轮叶片；马赫数；溢流孔；冷却通道；横流比；换热系数；数值模拟

Abstract: Heat transfer and flow characteristics in a rectangular channel with 90° and 45° effusion hole under the cross-flow Mach number of 0.2 and 0.7 have been numerically studied. The entrance Reynolds number is 8×104 and cross-flow ratio is 0.5 and 1. A smooth channel was also investigated to get a reference for calculation. Numerical results reveal that when both the entrance Reynolds number and cross-flow ratio are constant，with an increase in cross-flow Mach number from 0.2 to 0.7，the range of inverse flow in the effusion hole is decreased and thus the flow resistance is weakened. Besides，the local heat transfer near the effusion holes is weakened with increase of the cross-flow Mach numbers. Additionally，the cross-flow Mach number，under the low cross-flow ratio，has a stronger effect on the heat transfer on cooling channel wall in comparison with the high cross-flow ratio.

Key words: Turbine blade；Mach number；Effusion hole；Cooling channel；Cross-flow ratio；Heat transfer coefficient；Numerical simulation

苏文超,朱惠人,聂建豪. 横流马赫数对溢流孔附近流动及换热的影响 *[J]. 推进技术, 2014, 35(12): 1645-1652.

SU Wen-chao,ZHU Hui-ren,NIE Jian-hao. Effects of Cross-Flow Mach Number on Flow and Heat Transfer Characteristics Around Effusion Hole[J]. Journal of Propulsion Technology, 2014, 35(12): 1645-1652.

参考文献

[1] 倪萌, 朱惠人, 裘云, 等. 航空发动机涡轮叶片冷却技术综述[J].燃气轮机技术, 2005, 18(4): 25-33.
[2] Scheepers G, Morris R M. Experimental Study of Heat Transfer Augmentation Near the Entrance to a Film Cooling Hole in a Turbine Blade Cooling Passage[J]. Journal of Turbo-Machinery, 2009, 131(4):1-11.
[3] Ekkad S V, Huang Y, Han J. Detailed Heat Transfer Distributions in Two-Pass Square Channels with Rib Turbulators and Bleed Holes[J]. International Journal of Heat and Mass Transfer, 1998, 41(23): 3781-3791.
[4] Thurman D, Poinsatte P. Experimental Heat Transfer and Bulk Air Temperature Measurements for a Multi-pass Internal Cooling Model with Ribs and Bleed[J]. Journal of Turbo-Machinery, 2001, 123(1): 90-96.
[5] 裘云, 朱惠人, 许都纯, 等. 带肋壁与出流孔内流通道的流阻特性[J].推进技术, 2003, 24(4): 341-343. (QIU Yun, ZHU Hui-ren, XU Du-chun, et al. Pressure Loss of the Internal Passage with Rib Turbulators and Suction Holes[J]. Journal of Propulsion Technology, 2003, 24(4): 341-343.)
[6] 裘云. 带肋壁与气膜孔出流通道的流动特性研究[D].西安:西北工业大学, 2003.
[7] 杨力, 阚瑞, 任静, 等. 带气膜孔内部冷却通道的流动传热特性[J].工程热物理学报, 2011, 32(8): 1385-1388
[8] 陶智, 吴宏, 蔡毅. 气膜出流对叶片各内表面换热系数的影响[J].航空动力学报, 1997, 12 (4):413-415.
[9] 刘湘云, 陶智, 丁水汀, 等. 带60°肋U型通道中气膜孔对通道换热特性的影响[J].航空动力学报, 2005, 20(5): 822-826.
[10] 丁水汀, 侯晓静, 徐国强, 等. 矩形通道内气膜出流对内换热的影响规律[J].北京航空航天大学学报, 2007, 33(4):418-421.
[11] 徐磊, 常海萍, 常国强, 等. 叶片内部气膜孔附近壁面局部换热特性[J].推进技术, 2006, 27(3): 248-251.(XU Lei, CHANG Hai-ping, CHANG Guo-qiang, et al. Heat Transfer Characteristics Near a Row of Film Cooling Holes in Interior of Turbine Blade[J]. Journal of Propulsion Technology, 2006, 27(3): 248-251.
[12] 徐磊, 常海萍, 毛军逵, 等. 气膜出流冷气侧气膜孔附近壁面换热特性[J].推进技术, 2007, 28(2): 141-143.(XU Lei, CHANG Hai-ping, MAO Jun-kui, et al. Local Heat Transfer Characteristics Near Film Cooling Holes on Cooling Side in Film Cooling[J]. Journal of Propulsion Technology, 2007, 28(2): 141-143.)
[13] 王新月. 气体动力学基础[M].西安:西北工业大学出版社, 2006.
[14] 朱谷君. 工程传热传质学[M].北京:航空工业出版社, 1989.
[15] 裘云, 朱惠人, 许都纯, 等. 出流孔对内流通道壁面换热影响的实验[J].推进技术, 2002, 23(6): 477-479.(QIU Yun, ZHU Hui-ren, XU Du-chun, et al. Effect of Suction Hole on Heat Transfer Characteristic of Internal Passage[J]. Journal of Propulsion Technology, 2002, 23(6): 477-479.)(编辑:史亚红)　　　　　　　　　　　　　*　收稿日期:2013-11-02；修订日期:2013-12-23。基金项目:国家重点基础研发发展计划(2013CB035702)。作者简介:苏文超(1989—),男,硕士生,研究领域为航空发动机高温部件的传热与冷却技术。