气冷涡轮前缘冷气射流角度优化研究 *

推进技术 ›› 2014, Vol. 35 ›› Issue (12): 1653-1660.

气冷涡轮前缘冷气射流角度优化研究 *

洪博文,温风波,王松涛,崔　涛,王仲奇

哈尔滨工业大学能源科学与工程学院，黑龙江哈尔滨 150001,哈尔滨工业大学能源科学与工程学院，黑龙江哈尔滨 150001,哈尔滨工业大学能源科学与工程学院，黑龙江哈尔滨 150001,哈尔滨工业大学能源科学与工程学院，黑龙江哈尔滨 150001,哈尔滨工业大学能源科学与工程学院，黑龙江哈尔滨 150001

发布日期:2021-08-15
作者简介:洪博文(1989—)，男，硕士生，研究领域为气冷涡轮气动与传热。
基金资助:
国家自然科学基金委创新研究群体(51121004)。

Optimization Research of Cooling Gas Injection Angle at Leading Edge of Air-Cooled Turbine

School of Energy Science and Engineering，Harbin Institute of Technology，Harbin 150001，China,School of Energy Science and Engineering，Harbin Institute of Technology，Harbin 150001，China,School of Energy Science and Engineering，Harbin Institute of Technology，Harbin 150001，China,School of Energy Science and Engineering，Harbin Institute of Technology，Harbin 150001，China and School of Energy Science and Engineering，Harbin Institute of Technology，Harbin 150001，China

Published:2021-08-15

摘要/Abstract

摘要： 为了研究复合角度的圆形气膜孔对涡轮叶片冷却效果和气动性能的影响，利用SST的k-ω模型对涡轮叶栅进行数值模拟，对前缘区域冷却孔进行复合角度优化设计，给出前缘滞止线附近和吸力面改型前后的冷却特性分析。结果表明圆形气膜孔的复合角度对冷却和气动的影响明显，在前缘压力面，侧向角分别为85°，60°和45°，冷气在前缘处改变滞止点的位置，切向速度增大，冷却效果显著增强。在前缘吸力面上，冷却孔的入射角从45°变为30°，侧向角由-15°改为0°和30°，冷气与主流掺混减弱，壁面冷却效率增大，同时影响近壁面的主流从而改变流场结构。

关键词: 气冷涡轮；冷却效率；气膜冷却；复合角度；数值模拟

Abstract: In order to study the compound angle of circular film cooling holes on the cooling and aerodynamic performance of turbine blade，SST k-ω model was used to simulate the cooling holes on leading edge area ，which gives the cooling characteristics on stagnation line on leading edge and section side before and after retrofit. The results show that the compound angle of circular film-cooling hole does a great impact on cooling and aerodynamic performance. On pressure side of leading edge，the lateral angles of 85 °，60 ° and 45 °，the cooling air changes the position of stagnation point at leading edge，with the tangential velocity increasing，and the cooling effect is significantly enhanced. On section side of leading edge，the incident angle turns from 45°to 30°，the lateral angle changes from -15 ° to 0 ° and 30 °，the cooling air mixed with the mainstream is weaken to improve the cooling efficiency. Meanwhile ，it affects the mainstream near the wall and changes the structure of flow field.

Key words: Air-cooled turbine ; Cooling effectiveness ; Film cooling ; Compound angle ; Numerical simulation

洪博文,温风波,王松涛,崔　涛,王仲奇. 气冷涡轮前缘冷气射流角度优化研究 *[J]. 推进技术, 2014, 35(12): 1653-1660.

HONG Bo-wen,WEN Feng-bo,WANG Song-tao,CUI Tao,WANG Zhong-qi. Optimization Research of Cooling Gas Injection Angle at Leading Edge of Air-Cooled Turbine[J]. Journal of Propulsion Technology, 2014, 35(12): 1653-1660.

参考文献

[1] 刘捷, 安柏涛, 蒋洪德, 等. 静叶前缘气膜冷却特性的数值模拟及改进设计[J]. 航空动力学报, 2009, 24(2):331-339.
[2] Goldstein R J, Eckert E R G. Effects of Hole Geometry and Density on Three-Dimensional Film[J]. International Journal of Heat and Mass Transfer, 1974, 17(5):595-607.
[3] Leylek J H, Zekle R D. Discrete-Jet Film Cooling: a Comparison of Computational Results With Experiments[J]. Journal of Turbomachinery, 1994, 116(3): 358-368.
[4] Ligrani P, Wigle J, Ciriello S. Film-Cooling from Holes with Compound Angle Orientations , Part Ⅰ: Results Downstream of Two Staggered Rows of Holes with 3d Spanwise Spacing[J]. ASME Journal of Heat Transfer , 1994 , 116: 341-352.
[5] Ligrani P, Wigle J, Ciriello S, et al. Film Cooling From Holes With Compound Angle Orientations, Part I: Results Downstream of a Single Row of Holes with 6D Spanwise Spacing[J]. ASME Journal of Heat Transfer, 1994, 116: 353-362.
[6] Sen B, Schmidt D L, Bogard D G. Film Cooling with Compound Angle Holes: Heat Transfer[J]. ASME Journal of Turbomechinery, 1996, 118: 800-806.
[7] Schmidt D L, Sen B, Bogard D G. Film Cooling with Compound Angle Holes: Adiabatic Effectiveness [J]. ASME Journal of Turbomachinery, 1996, 118: 807-813.
[8] Ekkad S V, Zapata D, Han J C. Film Effectiveness over a Flat Surface with Air and CO₂ Injection Through Compound Angle Holes Using a Transient Liquid Crystal Image Method[J]. ASME Journal of Turbomachinery , 1997, 119: 580-586.
[9] Bunker R S. A Review of Shaped Hole Turbine Film-Cooling Technology[J]. Journal of Heat and Mass Transfer, 2005, 127: 441-453.
[10] 李少华, 彭涛, 张玉等. 复合角度对称射流气膜冷却效率的数值研究[J]. 动力工程, 2009, (03):236-240.
[11] 颜培刚, 王松涛, 韩万金. 涡轮叶栅前缘气膜冷却对气动参数影响的数值研究[J]. 推进技术, 2004 , 25 (1).(YAN Pei-gang, WANG Song-tao, HAN Wan-jin. Numerical Simulation of Influence of Leading Edge Film-Cooling on Aerodynamic Parameters in Turbine Cascade[J]. Journal of Propulsion Technology, 2004 , 25 (1).)
[12] 颜培刚, 王松涛, 韩万金, 等. 涡轮叶栅前缘气膜冷却数值模拟[J]. 航空动力学报, 2003, (5):623-628.
[13] 侯伟涛, 乔渭阳, 罗华龄. 压力面气膜冷却数值模拟[J]. 推进技术, 2009, 30(3):318-322.(Hou Wei-tao, QIAO Wei-yang, HAN Wan-jin. Numercial Simulation of the Pressure Side Film Cooling[J]. Journal of Propulsion Technology, 2009, 30(3):318-322.)
[14] 郭婷婷, 金建国, 李少华, 等. 不同出射角度对气膜冷却流场的影响[J]. 中国电机工程学报, 2006, 16:117-121.
[15] 迟重然. 气冷涡轮叶片的传热设计[D].哈尔滨:哈尔滨工业大学, 2011.
[16] 戴萍, 林枫. 涡轮叶片前缘气膜冷却数值模拟[J]. 航空动力学报, 2009, 24(3): 519-525.(编辑:史亚红)　　　　　　　　　　　　　*　收稿日期:2013-07-02；修订日期:2014-02-18。基金项目:国家自然科学基金委创新研究群体(51121004)。作者简介:洪博文(1989—),男,硕士生,研究领域为气冷涡轮气动与传热。E-mail:hbw1317@gmail.com