考虑油气传热传质耦合的轴承腔内壁油膜运动研究

推进技术 ›› 2014, Vol. 35 ›› Issue (7): 973-980.

考虑油气传热传质耦合的轴承腔内壁油膜运动研究

赵静宇,刘振侠,胡剑平,吕亚国

西北工业大学动力与能源学院，陕西西安 710072;西北工业大学动力与能源学院，陕西西安 710072;西北工业大学动力与能源学院，陕西西安 710072;西北工业大学动力与能源学院，陕西西安 710072

发布日期:2021-08-15
作者简介:赵静宇(1988—)，男，博士生，研究领域为航空宇航科学与技术。
基金资助:
西北工业大学基础研究基金(JC201140)；博士后科学基金(2011M501480)。

Motion of Wall Oil Film with Consideration of Oil-Gas Coupled Heat and Mass Transfer in Bearing Chamber

School of Power and Energy，Northwestern Polytechnical University，Xi’an 710072，China;School of Power and Energy，Northwestern Polytechnical University，Xi’an 710072，China;School of Power and Energy，Northwestern Polytechnical University，Xi’an 710072，China;School of Power and Energy，Northwestern Polytechnical University，Xi’an 710072，China

Published:2021-08-15

摘要/Abstract

摘要： 为研究航空发动机轴承腔油气两相流动及内壁面油膜运动特性，建立了腔内油滴-空气双向耦合数学模型和内壁面油膜传热传质运动模型，并对油气流场及不同供油流量下油膜的流动进行计算，获得腔内两相流场特性及内壁面油膜厚度、周向速度分布。结果表明:在所计算工况中，双向耦合计算流场与单向计算结果至少相差10%，因而不可忽略油滴对空气流动的影响；腔内滑油蒸汽质量分数低于0.05%，则空气-油滴之间粘性力产生的拖曳作用是影响流场的主要因素；随着供油流量的增加，油膜厚度及周向速度都呈增加趋势，但与滑油流量的增幅并不成正比。与国外试验数据的对比证明所建数学模型合理且有效。

关键词: 轴承腔；油气耦合；传热传质；运动特性；油膜厚度

Abstract: In order to study the oil/gas two-phase flow and motion characteristics of wall film in the aero-engine bearing chamber，the oil /air two-way coupled mathematical model and the oil film heat and mass transfer movement model were established. The oil/gas two-phase flow field and the motion characteristics of wall film with the oil flow rate were calculated，and the flow field characteristics，the thickness and circumferential velocity distribution of wall film were obtained. The results here show that，the flow field difference between two-way and one-way coupled calculation is at least 10%，and therefore the effects of oil droplets on air flow cannot be ignored in the calculation of two-phase flow. The oil vapor mass fraction in the bearing chamber is less than 0.05%，which indicates that the drag effect produced by viscous forces between the oil droplets and air is the main factor affecting the flow field. Both the oil film thickness and circumferential velocity show a trend of increasing with the increasing of the lubricating oil flow rate，but the increasing is not proportional to the increase amplitude of oil flow rate. Besides，the verification with the experimental data proves that the mathematical analysis model here is reasonable and effective.

Key words: Bearing chamber；Oil-gas coupling；Heat and mass transfer；Motion characteristics；Oil film thickness

赵静宇,刘振侠,胡剑平,吕亚国. 考虑油气传热传质耦合的轴承腔内壁油膜运动研究[J]. 推进技术, 2014, 35(7): 973-980.

ZHAO Jing-yu,LIU Zhen-xia,HU Jian-ping,LV Ya-guo. Motion of Wall Oil Film with Consideration of Oil-Gas Coupled Heat and Mass Transfer in Bearing Chamber[J]. Journal of Propulsion Technology, 2014, 35(7): 973-980.

参考文献

[1] 葛治美, 韩振兴, 张恩和, 等. 航空发动机轴承腔热分析计算 [J]. 航空动力学报, 2005, 20(3): 483-486.
[2] 刘振侠, 黄生勤, 吕亚国, 等. 航空发动机润滑系统通用分析软件开发 [J]. 航空动力学报, 2007, 22(1): 12-17.
[3] Busam S, Glahn A, Wttig S. Internal Bearing Chamber Wall Heat Transfer as a Function of Operating Conditions and Chamber Geometry [J]. Journal of Engineering for Gas Turbines and Power, 2000, 122(4): 314-320.
[4] Simmons K, Hibberd S, Yi Wang, et al. Numerical Study of the Two-Phase Air/oil Flow with an Aero-Engine Bearing Chamber Model Using a Coupled Lagrangian Droplet Tracking Method [R]. ASME PVP2002-1568.
[5] Glahn A, Wittig S. Two-Phase Air/Oil Flow in Aero Engine Bearing Chambers: Characterization of Oil Film Flows[J]. Journal of Engineering for Gas Turbines and Power,1996, 118(3): 578-583.
[6] Gorse P, Busam S. Dullenkopf K. Influence of Operating Condition and Geometry on the Oil Film Thickness in Aeroengine Bearing Chambers[J].Journal of Engineering for Gas Turbines and Power, 2006, 128(1): 103-110.
[7] Stanton D, Rutland C. Modeling Fuel Film Formation and Wall Interaction in Diesel Engines [R]. SAE Technical Paper Series, 960628, 1996.
[8] 陈薄, 陈国定, 王涛. 考虑油滴变形和二次油滴效应的轴承腔壁面油膜流动分析 [J].航空学报, 2013, 34(8): 1980-1989.
[9] Glahn A, Kurreck M, Willmann M, et al. Feasibility Study on Oil Droplet Flow Investigations Inside Aero Engine Bearing Chambers—PDPA Techniques in Combination with Numerical Approaches [J]. Journal of Engineering for Gas Turbines and Power, 1996, 118: 749-755.
[10] 胡剑平, 刘振侠, 张丽芬. 发动机整流支板大尺寸过冷水滴撞击特性 [J]. 航空学报, 2011, 32(10): 1778-1785.
[11] Berlemont A, Grancher M, Gouesbet G. On the Lagrangian Simulation of Turbulence Influence on Droplet Evaporation [J]. International Journal of Heat and Mass Transfer,1991, 34(11): 2805-2812.
[12] Berlemont A, Grancher M, Gouesbet G. Heat and Mass Transfer Coupling Between Vaporizing Droplets and Turbulence Using a Lagrangian Approach [J]. International Journal of Heat and Mass Transfer, 1994, 38(16): 3023-3034.
[13] Chengxin B, Gosman A D. Development of Methodology for Spray Impingement Simulation [R]. SAE Technical Paper Series, 950283, 1995.
[14] Chengxin B, Gosman A.D. Mathematical Modeling of Wall Films Formed by Impinging Sprays [R].SAE Technical Paper Series 960626, 1996.
[15] 陈国定, 陈薄, 王军, 等. 轴承腔中油滴尺寸分布和沉积特性 [J]. 机械工程学报, 2011, 47(10): 139-144.(编辑:朱立影)收稿日期:2013-10-23；修订日期:2013-11-21。基金项目:西北工业大学基础研究基金(JC201140)；博士后科学基金(2011M501480)。作者简介:赵静宇(1988—),男,博士生,研究领域为航空宇航科学与技术。E-mail:1528618784@qq.com