残余应变对锥柱形膜片多次翻转行为的影响研究

推进技术 ›› 2014, Vol. 35 ›› Issue (7): 981-987.

残余应变对锥柱形膜片多次翻转行为的影响研究

周算¹,强洪夫¹,王广¹,王学仁¹,周志清²

第二炮兵工程大学动力工程系，陕西西安 710025;第二炮兵工程大学动力工程系，陕西西安 710025;第二炮兵工程大学动力工程系，陕西西安 710025;第二炮兵工程大学动力工程系，陕西西安 710025;航天飞行器生存技术与效能评估实验室，北京 100085

发布日期:2021-08-15
作者简介:周　算(1984—)，男，博士生，研究领域为计算固体力学与结构优化设计。
基金资助:
国家973计划资助项目(61338)。

Effects of Residual Strain on Multi-Expulsion Behaviors for Spherical-Cone Diaphragms

Power Engineering Department，Xi’an Hi-Tech Institute，Xi’an 710025，China;Power Engineering Department，Xi’an Hi-Tech Institute，Xi’an 710025，China;Power Engineering Department，Xi’an Hi-Tech Institute，Xi’an 710025，China;Power Engineering Department，Xi’an Hi-Tech Institute，Xi’an 710025，China;Survival Technology and Efficiency Assessment of Aerospacecraft Laboratory，Beijing 100085，China

Published:2021-08-15

摘要/Abstract

摘要： 弧长法能跟踪复杂的非线性平衡路径全过程，但计算受初始设定载荷影响较大，而针对这一局限设计的改进算法能更好地求解膜片翻转过程。考虑新型Ti3012合金、纯钛、理想材料，基于改进弧长法研究残余应变对锥柱形膜片多次翻转行为的影响，得出新型Ti3012合金膜片的正翻与回翻过程均没有纯钛膜片好，且存在严重偏心现象，其98%正向翻转状态时回翻过程中不仅偏心量达到60mm，而且出现褶皱等严重失效行为；理想材料在不同正向翻转状态时反向回翻，膜片均存在严重的偏心问题，最大偏心量大于80mm；纯钛膜片仅98%正向翻转状态时回翻过程中偏心量稍大，约为10mm。无残余应变这一材料特性降低了膜片结构刚度，同时伴有初始弹性模量减小的性质，这些因素均不利于膜片多次翻转。

关键词: 锥柱形膜片；残余应变；多次翻转；弧长法；有限元法

Abstract: Arc length method can track nonlinear equilibrium configuration，but it is greatly affected by the initial setting load values. As a result，modified arc length method，aimed at solving the problem，works out expulsion process of diaphragms better. Several materials，such as 3012 titanium alloy，pure titanium and an ideal material，were chosen to study effects of residual stain on multi-expulsion behaviors for spherical-cone diaphragms based on modified arc length method by Finite Element Method(FEM). Positive expulsion and back reversal processes of 3012 titanium alloy diaphragms were not as good as that of pure titanium diaphragms. The former had severe eccentricity problems along with folding，and the eccentricity value reached at 60mm during back reversal process after 98 percent positive expulsion. Ideal material diaphragms all had severe eccentricity problems during back reversal process after positive expulsion of different percents，and the maximum eccentricity value was larger than 80mm. Pure titanium diaphragms had marked eccentricity phenomena only when back reversal process is at 98 percent positive expulsion，and the eccentricity value was about 10mm. Materials with no residual strain reduce structural stiffness of diaphragms，and coexist with the feature of initial elastic modulus being smaller. These factors are disadvantageous to multi-expulsion behaviors of diaphragms.

Key words: Spherical-cone diaphragms；Residual strain；Multi-expulsion；Arc length method；Finite element method

周算,强洪夫,王广,王学仁,周志清. 残余应变对锥柱形膜片多次翻转行为的影响研究[J]. 推进技术, 2014, 35(7): 981-987.

ZHOU Suan¹,QIANG Hong-fu¹,WANG Guang¹,WANG Xue-ren¹,ZHOU Zhi-qing². Effects of Residual Strain on Multi-Expulsion Behaviors for Spherical-Cone Diaphragms[J]. Journal of Propulsion Technology, 2014, 35(7): 981-987.

参考文献

[1] 毛根旺, 唐金兰. 航天器推进系统及其应用 [M]. 西安:西北工业大学出版社, 2009.
[2] Cardullo M W. Metal Expulsion Diaphragm Development for Spherical Propellant Tanks [R]. NASA 62-666.
[3] Stofan A J, Sumner I E. Experimental Investigation of the Slosh-Damping Effectiveness of Positive-Expulsion Bags and Diaphragms in Spherical Tanks [R]. NASA TN D-1712.
[4] Friona A J, Wood R. MX Stage4 Propellant Storage Assembly [R]. AD A103844: 97-111.
[5] 王刚. 推进剂管理用金属膜片挤压变形有限元分析[D]. 哈尔滨: 哈尔滨工业大学, 2009.
[6] 周仕明, 袁杰红. 金属膜片贮箱膜片变形的数值模拟与失效分析 [J]. 上海航天, 2005 (6): 13-16.
[7] 朱智春, 赵和明, 罗斌. 金属膜片贮箱的膜片变形分析[J]. 推进技术, 1999, 20(5): 77-79.(ZHU Zhi-chun, ZHAO He-ming, LUO Bin. Deformation Analysis of Metal Diaphragm for Positive Expulsion Tanks [J]. Journal of Propulsion Technology, 1999, 20(5): 77-79.)
[8] 吴安达, 王亲猛. 推进剂贮箱金属膜片的变形模拟及参数分析 [J]. 导弹与航天运载技术, 2012(3): 59-62.
[9] 吴安达, 王亲猛. 推进剂贮箱锥柱形金属膜片的翻转特性研究 [J]. 上海航天, 2012, 29(4): 59-62.
[10] 常宇. 贮箱隔膜变形行为的有限元分析[D]. 哈尔滨: 哈尔滨工业大学, 2006.
[11] 张绪虎, 唐斌, 李金山, 等. 航天器贮箱用钛制隔膜变形过程的数值模拟[J]. 宇航学报, 2010, 31(9): 2184-2188.
[12] 张增亭. 金属膜片贮箱膜片的数值仿真与试验验证 [J]. 火箭推进, 2009, 35(3): 26-29.
[13] 强洪夫, 周算, 王广, 等. 径厚比对锥柱形金属膜片屈曲和后屈曲状态的影响[J]. 航空动力学报, 2012, 27(11): 2521-2528.
[14] 朱志华, 胡小平, 陈香林. 钛制金属贮箱膜片的有限元分析 [J]. 火箭推进, 2007, 33(4): 32-35.
[15] Marvin M, Kammerer H, Gidley J T. Parametric Valuation of Contoured Aluminum Diaphragm Positive Expulsion Tanks [C]. Nashville: 28th AIAA/SAE/ASME/ ASEE Joint propulsion conference, 1992.
[16] Kammerer H, Hughes J, Gribben E. Analytical & Material Advances in Contoured Metal Diaphragms for Positive Expulsion Tanks [C]. San Diego: 31th AIAA/SAE/ASME/ASEE Joint Propulsion Conference, 1995.
[17] 何星星, 周仕明, 袁杰红. 锥柱形加筋金属膜片变形的数值仿真分析 [J]. 火箭推进, 2007, 33(6): 34-37.
[18] 何星星, 袁杰红, 周仕明. 内环向加筋圆柱形金属膜片变形数值仿真与失效分析 [J]. 强度与环境, 2007, 34(6): 16-21.
[19] 张付超. 考虑贮箱底座约束的金属膜片翻转变形可靠性数值分析 [D]. 北京: 北京工业大学, 2012.
[20] ZHAO Xiao, CHANG Hui, TANG Bin, et al. Numerical Analysis of Material Properties in Deformation of Near Hemispherical Shells [J]. Journal of Shanghai Jiaotong University.(Sci.), 2011, 16(2): 209-213.
[21] GAO En-zhi, LI Hong-wei, KOU Hong-chao, et al. Influences of Material Parameters on Deep Drawing of Thin-Walled Hemispheric Surface Part [J]. Transactions of Nonferrous Metals Society of China, 2009(19):433-437.
[22] 张绪虎, 唐斌, 李金山, 等. 材料参数对20L近半球形金属隔膜翻转性能的影响 [J]. 塑性工程学报, 2011, 18(5): 116-120.
[23] 周算, 强洪夫, 王广, 等. 锥柱形膜片后屈曲的材料特性预示研究 [J]. 力学与实践, 2012, 34(2): 24-28.
[24] 刘健, 林铁军, 练章华, 等. 考虑残余应变的连续油管螺旋屈曲载荷新公式 [J]. 石油机械, 2008, 36(1): 25-28.
[25] 杨娜, 龙丽华, 杨庆山. 残余应力对H型钢楔形梁相关屈曲的影响 [J]. 特种结构, 2006, 23(1): 13-16.
[26] 胡更开, 黄国良. 残余应力对复合材料弹－塑性变形的影响 [J]. 复合材料学报, 2000, 17(2): 60-65.
[27] 孙杰, 柯映林. 残余应力对航空整体结构件加工变形的影响分析 [J]. 机械工程学报, 2005, 41(2): 117-122.
[28] Obbard E G, Hao Y L, Akahori T, et al. Mechanics of Superelasticity in Ti-30Nb-(8-10)Ta-5Zr Alloy [J]. Acta Materialia, 2010(58): 3557-3567.
[29] 吴永礼. 计算固体力学方法[M]. 北京: 科学出版社, 2003.
[30] 凌道盛, 徐兴. 非线性有限元及程序[M]. 杭州: 浙江大学出版社, 2004.(编辑:史亚红)收稿日期:2013-04-20；修订日期:2013-09-02。基金项目:国家973计划资助项目(61338)。作者简介:周算(1984—),男,博士生,研究领域为计算固体力学与结构优化设计。E-mail:snail_xsy@sina.com