基于转捩模型的吸附式压气机正弯叶片数值研究

推进技术 ›› 2014, Vol. 35 ›› Issue (9): 1188-1193.

基于转捩模型的吸附式压气机正弯叶片数值研究

陈绍文¹,兰云鹤¹,王春雪²,周治华¹,王松涛¹

哈尔滨工业大学能源科学与工程学院，黑龙江哈尔滨 150001;哈尔滨工业大学能源科学与工程学院，黑龙江哈尔滨 150001;北京动力机械研究所，北京 100074;哈尔滨工业大学能源科学与工程学院，黑龙江哈尔滨 150001;哈尔滨工业大学能源科学与工程学院，黑龙江哈尔滨 150001

发布日期:2021-08-15
作者简介:陈绍文(1979—)，男，博士，副教授，研究领域为叶轮机械内流动。
基金资助:
国家自然科学基金项目(51206035)；国家自然科学基金创新研究群体项目(51121004)。

Numerical Study of Positively Curved Blade in Aspirated

Energy Science and Engineering School，Harbin Institute of Technology，Harbin 150001，China;Energy Science and Engineering School，Harbin Institute of Technology，Harbin 150001，China;Beijing Power Machinery Institute，Beijing 100074，China;Energy Science and Engineering School，Harbin Institute of Technology，Harbin 150001，China;Energy Science and Engineering School，Harbin Institute of Technology，Harbin 150001，China

Published:2021-08-15

摘要/Abstract

摘要： 采用三维数值方法研究了吸附式压气机扇形叶栅中正弯叶片的流场和气动性能，通过对比分析三种不同的孔式抽吸方案，以探讨附面层抽吸抑制三维流动分离、减小损失的机理。首先通过与前期实验数据的对比，校核了数值计算代码的可靠性，所得到的流场特性与实验数据有较好的一致性；其次通过在常规直叶片和正弯叶片中采用孔式附面层抽吸方法，以对比不同叶片积迭形式时附面层抽吸的效果，并探讨了通过改善抽吸设计方案提高抽吸效果的机理。结果表明，采用孔式抽吸可以较好地控制直、弯叶栅内的三维流动分离，抽吸后的吸力面气泡式分离消失，每个抽吸孔下游形成了新的基于抽吸孔特征的分离流动结构；抽吸策略的调整改善了角区的三维流动分离，尾迹旋涡的发展以及强度得到有效抑制。

关键词: 航空发动机；吸附式压气机；转捩模型；正弯叶片；数值研究

Abstract: Three-dimensional numerical method is adopted to study the flow field and aerodynamic performance of an aspirated compressor cascade with positively curved blades. Through a comparative analysis of three different hole-type suction schemes，the mechanisms of boundary layer suction inhibiting the 3D flow separation and reducing the loss were discussed. Firstly，the reliability of numerical calculation code is checked against the experimental data available from literature. The numerical flow-field characteristics has good agreement with the experimental data. Then，the effects of blade stacking styles on boundary layer suction are analyzed by using hole-type aspiration in straight and positively curved cascade，respectively，and the mechanisms for increasing the aspiration effect by improving aspiration-hole design schemes are discussed. The results show that the hole-type aspiration can control the three-dimensional flow separation well both in straight and positively curved cascades. With aspirated，the separation bubble on suction surface disappears and the new separation flow structures based on the aspiration-hole characteristics are generated at the downstream of the aspiration holes. The aspiration strategies are adjusting to improve the three-dimensional separation flow in the corner，therefore the development and intensity of wake vortex are restrained obviously.

Key words: Aircraft engine; Aspirated compressor；Transition model；Positively curved blade；Numerical investigation

陈绍文,兰云鹤,王春雪,周治华,王松涛. 基于转捩模型的吸附式压气机正弯叶片数值研究[J]. 推进技术, 2014, 35(9): 1188-1193.

CHEN Shao-wen¹,LAN Yun-he¹,WANG Chun-xue²,ZHOU Zhi-hua¹,WANG Song-tao¹. Numerical Study of Positively Curved Blade in Aspirated[J]. Journal of Propulsion Technology, 2014, 35(9): 1188-1193.

参考文献

[1] Kerrebrock J L,Reijnan D P,Ziminsky W S,et al.Aspirated Compressors[R].ASME 97-GT-52.
[2] Kerrebrock J L,Drela M,Merchant A A,et al.A Family of Designs for Aspirated Compressors[R].ASME 98-GT-196.
[3] Merchant A A,Drela M,Kerrebrock J L,et al.Aerodynamic Design and Analysis of a High Pressure Ratio Aspirated Compressor Stage[R].ASME 2000-GT-619.
[4] Merchant A A,Kerrebrock J L,Adamczyk J J,et al.Experimental Investigation of a High Pressure Ratio Aspirated Fan Stage[R].ASME 2004-GT-53679.
[5] Gbadebo S A,Cumpsty N A,Hynes T P.Control of Three-Dimensional Separations in Axial Compressors by Tailored Boundary Layer Suction[J].Journal of Turbomachinery,2007,130(1): 8.
[6] Gummer V,Goller M,Swoboda M.Numerical Investigation of Endwall Boundary Layer Removal on Highly-loaded Axial Compressor Stator[R].ASME 2005-GT-68699.
[7] Song Y P,Chen F,Yang J,et al.A Numerical Investigation of Boundary Layer Suction in Compound Lead Compressor Cascades[R].ASME 2005-GT-68441.
[8] 张华良,谭春青,张新敬,等.采用附面层抽吸控制流动分离的数值模拟[J].推进技术,2009,30(2): 192～196.(ZHANG Hua-liang,TAN Chun-qing,ZHANG Xin-jing,et al.Numerical Investigation on Application of Boundary Layer Suction to Control the Flow Separations[J].Journal of Propulsion Technology,2009,30(2): 192～196.)
[9] Guo S,Chen S W,Lu H W,et al.Enhancing Aerodynamic Performances of a High-Turning Compressor Cascade via Boundary Layer Suction[J].Science in China Series E,2010,53(10): 2748-2755.
[10] 刘波,项效镕,南向谊,等.附面层抽吸对叶栅表面分离流动控制的实验研究[J].推进技术,2009,30(6): 703-708.(LIU Bo,XIAO Xiao-rong,NAN Xiang-yi,et al.Experimental Investigation for Suppression Boundary Layer Separation on Cascade Surface by BLS[J].Journal of Propulsion Technology,2009,30(6): 703～708.)
[11] Ding J,Chen S W,Xu H,et al.Control of Flow Separations in Compressor Cascade by Boundary Layer Suction Holes in Suction Surface[R].ASME 2013-GT-94723.
[12] 陈绍文,陈浮,王可立,等.采用弯叶片的不同折转角压气机叶栅流场气动性能.推进技术,2007,28(2): 170～175.(CHEN Shao-wen,CHEN Fu,WANG Ke-li,et al.Aerodynamic Performance Study of Curved Compressor Cascades with Different Camber Angles[J].Journal of Propulsion Technology,2007,28(2): 170～175.)
[13] ANSYS CFX-Solver,Version 12.1: Theory[M].USA:ANSYS,Inc.Pennsylvania,2009.
[14] Menter F R,Langtry R B,Likki S R,et al.A Correlation Based Transition Model Using Local Variables Part 1-Model Formulation[R].ASME 2004-GT-53452.
[15] Langtry R B,Menter F R,Likki S R,et al.V?lker.A Correlation Based Transition Model Using Local Variables Part 2-Test Cases and Industrial Applications[R].ASME 2004-GT-53454.
[16] Langtry R B,Menter F R.Transition Modeling for General CFD Applications in Aeronautics[R].AIAA 2005-522.(编辑:张荣莉)收稿日期:2013-09-10；修订日期:2013-10-29。基金项目:国家自然科学基金项目(51206035)；国家自然科学基金创新研究群体项目(51121004)。作者简介:陈绍文(1979—),男,博士,副教授,研究领域为叶轮机械内流动。E-mail:cswemail@hit.edu.cn