非对称波瓣下外扩张角对S型喷管气动热力性能影响

推进技术 ›› 2015, Vol. 36 ›› Issue (5): 678-687.

非对称波瓣下外扩张角对S型喷管气动热力性能影响

刘友宏¹,杜力伟¹,李　腾¹,邵万仁²,徐　速²,邓洪伟²

北京航空航天大学能源与动力工程学院/航空发动机气动热力国家级重点实验室，北京 100191,北京航空航天大学能源与动力工程学院/航空发动机气动热力国家级重点实验室，北京 100191,北京航空航天大学能源与动力工程学院/航空发动机气动热力国家级重点实验室，北京 100191,中国航空工业集团公司沈阳发动机设计研究所，辽宁沈阳 110015,中国航空工业集团公司沈阳发动机设计研究所，辽宁沈阳 110015,中国航空工业集团公司沈阳发动机设计研究所，辽宁沈阳 110015

发布日期:2021-08-15
作者简介:刘友宏(1963—)，男，博士，教授，研究领域为传热传质。

Effects of Downward-Outward Penetration Angle of an Asymmetric Lobed Mixer on Aero-Thermal Dynamical Performance of an S-Shaped Nozzle

National Key Laboratory of Science and Technology on Aero-Engine Aero-Thermodynamics，School of Energy and Power Engineering，Beihang University，Beijing 100191，China,National Key Laboratory of Science and Technology on Aero-Engine Aero-Thermodynamics，School of Energy and Power Engineering，Beihang University，Beijing 100191，China,National Key Laboratory of Science and Technology on Aero-Engine Aero-Thermodynamics，School of Energy and Power Engineering，Beihang University，Beijing 100191，China,Shenyang Aero-Engine Design Institute，Aviation Industry Corporation of China，Shenyang 110015，China,Shenyang Aero-Engine Design Institute，Aviation Industry Corporation of China，Shenyang 110015，China and Shenyang Aero-Engine Design Institute，Aviation Industry Corporation of China，Shenyang 110015，China

Published:2021-08-15

摘要/Abstract

摘要： 为了研究非对称波瓣下外扩张角对S型喷管气动热力性能的影响规律，以含非对称波瓣的S型喷管为研究对象，保持非对称波瓣长度、内扩张角、高宽比及上外扩张角不变，取定非对称波瓣下外扩张角依次为17.75°，22.75°，27.75°，32.75°，建立了一组具有不同下外扩张角的非对称波瓣S型喷管模型。通过数值求解Reynolds-Averaged Navier-Stokes(RANS)方程，得到了S型喷管气动热力性能随非对称波瓣下外扩张角的变化规律。研究结果表明:第一个弯道上游流场中，流向涡具有较强的混合能力，其核心区无量纲涡量值随非对称波瓣下外扩张角增大而逐渐增大；然而，在第一个弯道下游流场中，所有模型对应的流向涡核心区无量纲涡量值均已非常微弱。在S型喷管弯道区域，流道流向、截面形状发生巨大改变，使得内外涵流体混合效果显著提高，但混合流体的总压恢复系数却急剧下降。混合流体热混合效率值受下外扩张角影响不明显，但S型喷管下半部分内壁面温度随下外扩张角增大而逐渐上升。在S型喷管出口，下外扩张角为17.75°模型的总压恢复系数为0.9464，高于其他3种模型，并且相对于该截面上总压恢复系数最低值增加了0.55%。

关键词: 非对称波瓣；S型喷管；下外扩张角；流向涡；热混合效率；总压恢复系数

Abstract: For the aim of investigating the effects of downward-outward penetration angle of an asymmetric lobed mixer on aero-thermal dynamical performance of an S-shaped nozzle，a series of geometrical models were developed. In the studied geometrical models，lobe length，inner penetration angle，ratio of height to width and upward-outward penetration angle were all kept constant，only with the downward-outward penetration angle being set as 17.75°，22.75°，27.75°and 32.75°，respectively. Through iterating the Reynolds-Averaged Navier-Stokes (RANS) equations，qualitative and quantitative effect of downward-outward penetration angle on performance of the studied S-shaped nozzle was obtained. The results show that in the flow field upstream of the first bend of the S-shaped nozzle the stream-wise vorticity is suggested to be the vorticity with high magnitude and the magnitude is found to be increased as a response to the more aggressive downward-outward penetration angle. The results also show that magnitudes of the stream-wise vorticity are suggested to be low enough in the flow field downstream of the first bend for all studied models. The thermal mixing efficiency is shown to be experienced a fast-rising process within the bends of the studied S-shaped nozzle due to the conspicuous change of both the flow direction and the detailed shape of the cross section. However，the total pressure recovery coefficient is observed to decrease significantly within this region. As the downward-outward penetration angle increased，noteworthy change of the thermal mixing efficiency was not figured，but the temperature of the bottom wall of the investigated S-shaped nozzle is shown to be enhanced gradually. In the cross section of the S-shaped nozzle outlet，the model with a downward-outward penetration angle of 17.75° is found to have the maximum total pressure recovery coefficient of 0.9464，which is 0.55% higher than the minimum value in this cross section.

Key words: Asymmetric lobed mixer; S-shaped nozzle;Downward-outward penetration angle; Stream-wise vorticity; Thermal mixing efficiency; Total-pressure recovery coefficient

刘友宏,杜力伟,李　腾,邵万仁,徐　速,邓洪伟. 非对称波瓣下外扩张角对S型喷管气动热力性能影响[J]. 推进技术, 2015, 36(5): 678-687.

LIU You-hong¹,DU Li-wei¹,LI Teng¹,SHAO Wan-ren²,XU Su²,DENG Hong-wei². Effects of Downward-Outward Penetration Angle of an Asymmetric Lobed Mixer on Aero-Thermal Dynamical Performance of an S-Shaped Nozzle[J]. Journal of Propulsion Technology, 2015, 36(5): 678-687.

参考文献

[1] Presz Jr W M, Reynolds G, McCormick D. Thrust Augmentation Using Mixer-Ejector Diffuser Systems [R]. AIAA 94-0020.
[2] 张靖周, 李立国. 波瓣喷管红外抑制系统的实验研究[J]. 航空动力学报, 1997, 12(2): 212-214.
[3] 单勇, 张靖周, 邵万仁, 等. 某型涡扇排气系统缩比模型红外辐射特性实验[J].航空动力学报, 2009, 24(10):2228-2234.
[4] Presz W M, Morin B K L, Gousy R G. Forced Mixer Lobes in Ejector Designs[J]. Journal of Propulsion and Power, 1988, 4(4):350-355.
[5] Skebe S A, Paterson R W, Barber T J. Experimental Investigation of Three Dimensional Forced Mixer Lobe Flow Fields[J]. AIAA Journal, 1988, 10:1999-2006.
[6] Simon C M Yu, Yip T H, Liu C Y. Mixing Characteristics of Forced Mixers with Scalloped Lobes[J]. Journal of Propulsion and Power, 1997, 13(2):305-311.
[7] R Ramesh Kumar, Job Kurian. Coaxial Jets from Lobed-Mixer Nozzles[J]. AIAA Journal, 1996, 34(9):1822-1829.
[8] Zaman K B M Q, Wang F Y, Georgiadis N J. Noise, Turbulence, and Thrust of Subsonic Freejets from Lobed Nozzles[J]. AIAA Journal, 2003, 41(3):398-498.
[9] 刘友宏, 樊超, 谢翌, 等. 波瓣数对波瓣强迫混合排气系统性能影响[J]. 航空动力学报, 2010, 25(8):1683-1689.
[10] 谢翌, 刘友宏. 瓣高宽比对波瓣强迫混合排气系统性能影响[J]. 航空动力学报, 2010, 25(12):2787-2794.
[11] 谢翌, 刘友宏. 波瓣穿透率对波瓣混合排气系统性能影响[J].推进技术, 2011, 32(2):207-213.(XIE Yi, LIU You-hong. Effects of Lobe Penetration Ratio on Performance of Mixer Exhaust System[J]. Journal of Propulsion Technology, 2011, 32(2):207-213.)
[12] 谢翌, 阮登芳, 钟晨, 等. 波瓣帽罩结构和脊线对混合排气系统性能影响[J].推进技术, 2014, 35(3):314-319.(XIE Yi, RUAN Deng-fang, ZHONG Chen, et al. Effects of Lobe Cap and Crest Line on Performance of Mixing Exhaust System[J]. Journal of Propulsion Technology, 2014, 35(3):314-319.)
[13] 刘友宏, 张少鹏, 杨旭, 等. 波瓣尾缘切角对涡扇发动机混合排气系统气动热力性能影响[J].推进技术, 2013, 34(6):734-740.(LIU You-hong, ZHANG Shao-peng, YANG Xu, et al. Effects of Cut Angles at Trailing Edge of Lobe on Aerothermodynamic Performance of Forced Mixing Exhaust System in Turbofan Engine[J]. Journal of Propulsion Technology, 2013, 34(6):734-740.)
[14] Cooper N J, Merati P, Hu H. Numerical Simulation of the Vortical Structures in a Lobed Jet Mixing Flow[R]. AIAA 2005-0635.
[15] 李立国, 张靖周. 航空用引射混合器[M].北京:国防工业出版社, 2007.
[16] Xie Y, Liu Y H. A Modified Thermal Mixing Efficiency and its Application to Lobed Mixer Nozzle for Aero-Engines[J]. Heat Transfer Research, 2011, 42(4):317-335.
[17] 谢翌. 涡扇发动机波瓣混合排气系统气动热力性能研究[D].北京:北京航空航天大学, 2012.
[18] Xie Y, Liu Y. Numerical Investigation of Mixing Length on Performance of Lobed Forced Mixer Nozzles[J]. Heat Transfer—Asian Research, 2011, 40(3):205-216.
[19] 刘友宏, 谢翌, 郭楠.尾缘凹扇及综合修形对波瓣混合器性能影响[J].航空动力学报, 2010, 25(2):243-250.(编辑:朱立影)　　　　　　　　　　　　　*　收稿日期:2014-04-01；修订日期:2014-07-11。作者简介:刘友宏(1963—),男,博士,教授,研究领域为传热传质。E-mail:liuyh@buaa.edu.cn