静压支承摩擦副温度场模拟与实验

推进技术 ›› 2016, Vol. 37 ›› Issue (10): 1946-1951.

静压支承摩擦副温度场模拟与实验

于晓东,吴晓刚,隋甲龙,孙丹丹,张艳芹

哈尔滨理工大学机械动力工程学院，黑龙江哈尔滨 150080,哈尔滨理工大学机械动力工程学院，黑龙江哈尔滨 150080,哈尔滨理工大学机械动力工程学院，黑龙江哈尔滨 150080,哈尔滨理工大学机械动力工程学院，黑龙江哈尔滨 150080,哈尔滨理工大学机械动力工程学院，黑龙江哈尔滨 150080

发布日期:2021-08-15
作者简介:于晓东，博士，教授，研究领域为润滑理论及摩擦学。
基金资助:
国家自然科学基金(51375123；51075106)；黑龙江省自然科学基金(E2016040)。

Numerical and Experimental Study on Temperature Field of Hydrostatic Bearing Friction Pairs

Mechanical Power & Engineering College，Harbin University of Science and Technology，Harbin 150080，China,Mechanical Power & Engineering College，Harbin University of Science and Technology，Harbin 150080，China,Mechanical Power & Engineering College，Harbin University of Science and Technology，Harbin 150080，China,Mechanical Power & Engineering College，Harbin University of Science and Technology，Harbin 150080，China and Mechanical Power & Engineering College，Harbin University of Science and Technology，Harbin 150080，China

Published:2021-08-15

摘要/Abstract

摘要： 为了研究静压支承摩擦副温度场，基于摩擦学和传热学理论，采用流固耦合方法对圆形腔静压支承摩擦副的温度分布规律及其速度特性进行研究，并进行实验验证。结果表明:间隙油膜在挤压和剪切以及泵功耗联合作用下产生的热，通过流固耦合方式传递给静压导轨和油垫，进而扩散到整个旋转工作台和底座。间隙油膜接触处摩擦副温度最高，向四周扩散温度逐渐降低。随着旋转工作台转速增加，油膜温度上升，工作台上表面和侧面温度下降，并趋于平缓，底座侧面温度从下到上先升高后降低。旋转速度由10 r/min增加至80 r/min时旋转工作台最高温升为6.8℃，底座最高温升为3.5℃，因而旋转速度对支承摩擦副温度场影响不能忽略。并将实验结果与模拟值进行比较，温度相对误差均在4%以下，满足工程实践要求。

关键词: 温度场；静压支承摩擦副；静压推力轴承；流固耦合；实验研究

Abstract: In order to study temperature field of hydrostatic bearing friction pairs，temperature distribution and its speed characteristics of hydrostatic bearing friction pairs with circular recess are analyzed by adopting the method of fluid-structure interaction based on tribology theory and heat transfer，and a verification experiment is carried on. Due to the joint action of oil film extrusion，oil shear and pump power consumption，and a large amount of heat is generated in the oil film clearance during the operation of hydrostatic thrust bearing，and heat is passed to the hydrostatic slideway and pad by way of fluid-solid interaction，and then heat spreads to the entire rotational workbench and base. The temperature of friction pairs is the highest in the place that is contacting with oil film clearance，and temperature decreases gradually to all around. The results have been found that by increasing the rotational speed oil film temperature increased，and temperature of upper surface and side surface is decreased，and then tends to be steady，and temperature of side surface of base increased and then decreased from bottom to upper. The highest temperature rise of the rotational workbench was 6.8℃ when the rotational speed was from 10 r/min to 80 r/min，but the highest temperature rise of the base was 3.5℃，and therefore the effects of rotational speed on temperature field of hydrostatic bearing friction pairs cannot be ignored in the thermal calculation of hydrostatic bearing friction pairs. Comparison between experimental data with simulation values shows that the maximum error of temperature is less than 4%，meeting the actual requirements.

Key words: Temperature field；Hydrostatic bearing friction pairs；Hydrostatic thrust bearing；Fluid-solid interaction；Experimental research

于晓东,吴晓刚,隋甲龙,孙丹丹,张艳芹. 静压支承摩擦副温度场模拟与实验[J]. 推进技术, 2016, 37(10): 1946-1951.

YU Xiao-dong,WU Xiao-gang,SUI Jia-long,SUN Dan-dan,ZHANG Yan-qin. Numerical and Experimental Study on Temperature Field of Hydrostatic Bearing Friction Pairs[J]. Journal of Propulsion Technology, 2016, 37(10): 1946-1951.

参考文献

[1] 王建磊, 李军杰, 杨培基, 等. 动静压轴承温度场和热变形的仿真分析[C]. 南京:第十届全国振动理论及应用学术会议, 2011.
[2] 郝胜强, 张新宇, 吴士海, 等. 球磨机静压轴承油膜温度场数值模拟与分析[J]. 辽宁科技大学学报, 2012, 35 (2): 130-133.
[3] 王燕霜, 刘喆, 朱海峰. 轴连轴承温度场分析[J]. 机械工程学报, 2011, 47(17): 84-91.
[4] 徐建宁, 屈文涛, 赵宁. 止推滑动轴承的温度场和热变形分析[J]. 润滑与密封, 2006, 8: 120-122.
[5] 周建芳. 流气耦合状态下动静压轴承油膜温度场分析[D]. 洛阳:河南科技大学, 2012.
[6] 郭力, 李波, 章泽. 液体动静压轴承的温度场与热变形仿真分析[J]. 机械科学与技术, 2014, 33(4): 511-515.
[7] 刘思仁. 高速动静压轴承油膜温度场的分析与研究[D]. 上海:东华大学, 2011.
[8] 张艳芹. 重型静压推力轴承综合物理场研究[D]. 哈尔滨:哈尔滨理工大学, 2009.
[9] 于晓东, 邱志新, 李欢欢, 等. 扇形腔多油垫静压推力轴承润滑性能的速度特性[J]. 热能动力工程, 2013, 28(3): 289-293.
[10] 于晓东. 重型静压推力轴承力学性能及油膜态数值模拟研究[D]. 哈尔滨:东北林业大学, 2007.
[11] 赵雄, 董跃, 张晓阳, 等. 液体动静压支承的功率消耗及温升研究[J]. 组合机床与自动化加工技术, 2003, 11: 51-53.
[12] 徐晓秋. 回油槽结构参数对静压推力轴承内部流场影响研究[D]. 哈尔滨:哈尔滨理工大学, 2012.
[13] Novikov E A, Shitikov I A, Maksimov V A. Calculation of the Characteristics of a Hydrostatic Ring Thrust Bearing for Refrigeration Compressors[J]. Chemical and Petroleum Engineering, 2004, 40(40): 23-26.
[14] Fazil Canbulut, Cem Sinanoglu, Sahin Yildirim. Analysis of Effects of Sizes of Orifice and Pocket on the Rigidity of Hydrostatic Bearing Using Neural Network Predictor System[J]. KSME International Journal, 2004, 18(3): 432-442.
[15] Zhang Yanqin, Yu Zeyang, Chen Yao. Simulation and Experimental Study of Lubrication Characteristics of Vertical Hydrostatic Guide Rail[J]. High Technology Letters, 2014, 20(3): 315-320.
[16] Zhang Yan-Qin, Fan Li-Guo. Simulation and Experimental Analysis on Supporting Characteristics of Multiple Oil Pad Hydrostatic Bearing Disk[J]. Journal of Hydrodynamics, 2013, 25(2): 236-241.
[17] Yanqin Zhang, Weiwei Li, Zeyang Yu. Flow Criterion Research on Fluid in Hydrostatic Bearing from Laminar to Turbulent Transition [J]. International Journal of Hybrid Information Technology, 2014, 7(3): 369-374.
[18] Yanqin Zhang, Yao Chen, Zeyang Yu. Influence of Strengthening Rib Location on Temperature Distribution of Heavy Vertical Lathe Worktable[J]. International Journal of u-and e-Service, Science and Technology, 2014, 7(1): 65-71.
[19] YanQin Zhang, WeWei Li, LiGuo Fan. Simulation and Experimental Analysis of Influence of Inlet Flow on Heavy Hydrostatic Bearing Temperature Field[J]. Asian Journal of Chemistry, 2014, 26(17): 5478-5482.
[20] 韩东江, 杨金福, 陈昌婷, 等. 轴承供气压力对静压气体轴承-转子系统动力学特性影响的实验[J]. 推进技术, 2014, 35(9): 1265-1270. (HAN Dong-jiang, YANG Jin-fu, CHEN Chang-ting, et al. Experimental Research for Effects of Bearing Supply Gas Pressure on Aerostatic Bearing-Rotor System Dynamic Characteristics[J]. Journal of Propulsion Technology, 2014, 35(9): 1265-1270.)
[21] 钟冲, 刘振侠, 胡剑平, 等. 轴承腔壁面油膜厚度超声测量实验研究[J]. 推进技术, 2014, 35(8):1110-1115. (ZHONG Chong, LIU Zhen-xia, HU Jian-ping, et al. Experimental Study of Ultrasonic Measurement of Oil Film Thickness in Bearing Chamber Wall[J]. Journal of Propulsion Technology, 2014, 35(8): 1110-1115.)
[22] 丁振坤. 液体静压支承设计[M]. 上海:上海科学技术出版社, 1986.
[23] 陈燕生. 液体静压支承原理和设计[M]. 北京:国防工业出版社, 1980.
[24] 庞志成. 液体气体静压技术[M]. 哈尔滨:黑龙江人民出版社, 1981.
[25] 王福军. 计算流体动力学分析—FLUENT软件原理与应用[M]. 北京:清华大学出版社, 2004.
[26] 韩占忠, 王敬, 兰小平. FLUENT流体工程仿真计算实例与应用[M]. 北京:北京理工大学出版社, 2004.　　　　　　　　　　　　　*　收稿日期:2015-05-15；修订日期:2015-07-13。基金项目:国家自然科学基金(51375123；51075106)；黑龙江省自然科学基金(E2016040)。作者简介:于晓东,博士,教授,研究领域为润滑理论及摩擦学。E-mail: hustyuxiaodong@163.com(编辑:朱立影)