叶型孔式预旋喷嘴流动特性数值研究

推进技术 ›› 2016, Vol. 37 ›› Issue (2): 332-338.

叶型孔式预旋喷嘴流动特性数值研究

刘育心¹,刘高文¹,吴衡¹,田淑青²

西北工业大学动力与能源学院，陕西西安 710072,西北工业大学动力与能源学院，陕西西安 710072,西北工业大学动力与能源学院，陕西西安 710072,中航商用航空发动机有限责任公司，上海 201108

发布日期:2021-08-15
作者简介:刘育心，女，博士，研究领域为发动机空气系统和旋转盘腔中的流动换热。E-mail: liuyuxin_lz@163.com 通讯作者:刘高文，男，博士，副教授，研究领域为发动机空气系统和旋转盘腔中的流动换热。
基金资助:
国家自然科学基金(51476133)。

Numerical Investigation on Flow Characteristics of a Vane

School of Power and Energy，Northwestern Poly-Technical University，Xi’an 710072，China,School of Power and Energy，Northwestern Poly-Technical University，Xi’an 710072，China,School of Power and Energy，Northwestern Poly-Technical University，Xi’an 710072，China and AVIC Commercial Aircraft Engine Co.，Ltd，Shanghai 201108，China

Published:2021-08-15

摘要/Abstract

摘要： 现有研究表明叶片式喷嘴是目前为止性能最好的预旋喷嘴。而在整环的喷嘴盘设计中，当喷嘴总面积、预旋角度、喷嘴数目和半径位置确定后，喷嘴叶高和栅距就固定下来，往往因为叶高与栅距的比值过小而大大降低喷嘴性能。在叶片式喷嘴基础上提出了一种能够调整喷嘴叶高到恰当值的新型预旋喷嘴——叶型孔式喷嘴(vane shaped hole nozzle，vsh nozzle)。采用数值方法深入对比研究了叶型孔式喷嘴与叶片式喷嘴的性能差异。为了考虑喷嘴下游预旋腔的掺混影响，计算域不仅包括静止的进气腔和喷嘴，还包括转动的预旋腔和接受孔。计算结果表明，叶型孔式预旋喷嘴的流量系数和预旋效率显著高于叶片式喷嘴，vsh-52喷嘴的流量系数比vane-52喷嘴高9.14%，预旋效率高4.44%。还提出采用有效流量系数、有效预旋效率两个参数来体现考虑喷嘴下游预旋腔掺混影响的喷嘴综合性能。

关键词: 预旋系统；预旋喷嘴；叶片；流量系数；预旋效率

Abstract: Investigations on preswirl nozzle show that the cascade vane nozzle is the best one so far. While in the design of whole circular nozzle disc，the blade height and blade spacing will be settled with the throat area，preswirl angle，number and radial position of nozzle decided. If the ratio between blade height and blade spacing is too small，it will reduce the performance of nozzle significantly. Based on the vane nozzle，a new kind of preswirl nozzle called vane shaped hole preswirl nozzle(vsh nozzle for short) is proposed，with which the ratio of blade height against blade spacing can be adjusted to a more appropriate value. The flow characteristics of vane nozzle and vane shaped hole nozzle are compared numerically . To consider the mixing influence of preswirl cavity downstream the nozzle，the computational models contain not only the stationary inlet chamber and preswirl nozzle ，but also the rotary preswirl cavity and receiver hole. Results show that the discharge coefficient and preswirl effectiveness of the vsh nozzle are higher remarkably than that of vane nozzle. The discharge coefficient of the vsh-52 preswirl nozzle increased by 9.14% comparing with that of the vane-52 nozzle，and the preswirl effectiveness increased by about 4.44%. Two new parameters called effective discharge coefficient and effective preswirl effectiveness are also proposed to reflect the comprehensive performance considering the mixing influence of preswirl cavity downstream the nozzle.

Key words: Preswirl system；Preswirl nozzle；Vane；Discharge coefficient；Preswirl effectiveness

刘育心,刘高文,吴衡,田淑青. 叶型孔式预旋喷嘴流动特性数值研究[J]. 推进技术, 2016, 37(2): 332-338.

LIU Yu-xin¹,LIU Gao-wen¹,WU Heng¹,TIAN Shu-qing². Numerical Investigation on Flow Characteristics of a Vane[J]. Journal of Propulsion Technology, 2016, 37(2): 332-338.

参考文献

[1] Meierhofer B, Franklin C J. An Investigation of a Pre-Swirled Cooling Airflow to a Turbine Disc by Measuring the Air Temperature in the Rotating Channels[R]. ASME 81-GT-132.
[2] Dittman M. Discharge Coefficients of a Pre-Swirl System in Secondary Air System[R]. ASME 2001-GT-0122.
[3] Geis T. Cooling Air Temperature Reduction in a Direct Transfer Pre-Swirl System[R]. ASME GT2003-38231.
[4] Bricaud C, Geis T, Dullenkopf K, at al. Measurement and Analysis of Aerodynamic and Thermodynamic Losses in Pre-Swirl System Arrangement[R]. ASME 2007- GT-27191.
[5] Lewis P, Wilson M, Lock G J, et al. Effect of Radial Location of Nozzle on Performance of Pre-Swirl Systems[R]. ASME 2008-GT -50295.
[6] Yan Y , Gord M F, Lock G D , et al. Fluid Dynamics of a Pre-Swirl Rotor-Stator System[R]. ASME GT-2002-30415.
[7] Javiya U. A Comparative Study of Cascade Vanes and Drilled Nozzle Design for Pre-Swirl[R]. ASME 2011-GT-46006.
[8] 冶萍, 张靖周. 有预旋进气转静盘腔中的流动和换热特性数值研究[J]. 航空动力学报, 2004, 19(3):370-374.
[9] 丁水汀, 陶智, 徐国强, 等. 带进气预旋的旋转空腔平均换热特性研究[J]. 航空动力学报, 1998, 13 (3): 277-280.
[10] 徐国强, 陶智, 丁水汀, 等. 中心进气旋转盘流动与换热的数值研究[J]. 航空动力学报, 2000, 15(2): 169－173.
[11] 罗翔, 徐国强, 陶智, 等. 进气角度对旋转盘冷却效果的影响[J]. 推进技术, 2007, 28 (3): 240-243. (LUO Xiang, XU Guo-qiang, TAO Zhi, et al. Cooling Effectiveness in a Rotor-Stator System with Different Pre-Swirl Angles[J]. Journal of Propulsion Technology, 2007, 28(3): 240-243.)
[12] 朱晓华, 刘高文, 刘松龄, 等. 带盖板的预旋系统降温和压力损失数值研究[J]. 航空动力学报, 2010, 25(11): 2498-2506.
[13] 刘高文, 李碧云, 蒋兆午, 等. 预旋角度对预旋孔流动特性的影响[J]. 推进技术, 2012, 33(5): 740-746. (LIU Gao-wen, LI Bi-yun, JIANG Zhao-wu, et al. Effects of Pre-Swirl Angle on Flow Characteristics of Pre-Swirl Nozzle[J]. Journal of Propulsion Technology, 2012, 33(5): 740-746.)
[14] 刘高文, 张林, 李碧云, 等. 扩口孔型预旋喷嘴流动与温降特性 [J]. 推进技术, 2013, 34(3): 390-396. (LIU Gao-wen, Zhang Lin, LI Bi-yun, et al. Investigation on Flow Characteristics and Temperature Drop of an Aerodynamic-Hole Typed Pre-Swirl Nozzle[J]. Journal of Propulsion Technology, 2013, 34(3): 390-396.)
[15] 刘育心, 刘高文, 徐权, 等. 无量纲叶高对叶型喷嘴流动特性的影响[J]. 推进技术, 2015, 36(3). (LIU Yu-xin, LIU Gao-wen, XU Quan, et al. Influences of Non-Dimensional Blade Height on the Flow Characteristics of Cascade Vane Preswirl Nozzle[J]. Journal of Propulsion Technology, 2015, 36(3).)
[16] 康松, 杨建明, 胥建群, 等. 汽轮机原理[M]. 北京:中国电力出版社, 2000.
[17] 隋秀明, 赵庆军, 赵晓路, 等. 低进气度部分进气涡轮气动设计与内部流动研究[J]. 工程热物理学报, 2013, 34(3):419-422.
[18] 阳虹, 杨建道, 李军, 等. 汽轮机调节级气动性能分析和结构优化设计[J]. 热力透平, 2011, 40 (1): 5-10.(编辑:史亚红) 　　　　　　　　　　　　　*　收稿日期:2014-10-13；修订日期:2014-12-17。基金项目:国家自然科学基金(51476133)。作者简介:刘育心,女,博士,研究领域为发动机空气系统和旋转盘腔中的流动换热。E-mail: liuyuxin_lz@163.com通讯作者:刘高文,男,博士,副教授,研究领域为发动机空气系统和旋转盘腔中的流动换热。E-mail: gwliu@nwpu.edu.cn