气相环境下EPDM绝热材料双区体烧蚀模型

推进技术 ›› 2016, Vol. 37 ›› Issue (2): 378-385.

气相环境下EPDM绝热材料双区体烧蚀模型

王书贤¹,李江²,蔡霞¹

西安航空学院，陕西西安 710077,西北工业大学燃烧、流动和热结构国家级重点实验室，陕西西安 710072,西安航空学院，陕西西安 710077

发布日期:2021-08-15
作者简介:王书贤，女，博士，讲师，研究领域为发动机热防护。
基金资助:
西安市科技计划项目(CXY1518(5))。

Bulk Ablation Model with Double Zones for EPDM

Xi’an Aeronautical University，Xi’an 710077，China,National Key Laboratory of Combustion， Flow and Thermal-Structure，Northwestern Polytechnical University，Xi’an 710072，China and Xi’an Aeronautical University，Xi’an 710077，China

Published:2021-08-15

摘要/Abstract

摘要： 针对气相环境下EPDM绝热材料的烧蚀行为建立了双区体烧蚀模型，着重考虑了沉积反应、气流剥蚀和膨胀现象。多孔介质区和固体区分开求解，采用交界面温度耦合的数值处理方法。对气相环境下的烧蚀实验开展了数值计算，分析了影响炭化层孔隙结构、质量烧蚀率的主要因素，计算结果与实验结果吻合较好。计算还获得了炭化层内烧蚀气体流速的量级是毫米到厘米，相对压强的量级是103～104Pa以及相对压强的分布情况。

关键词: 固体火箭发动机；烧蚀模型；沉积反应；气流剥蚀；膨胀；孔隙结构；烧蚀气体

Abstract: According to the ablation behavior of EPDM insulator in gas environment，a double zones bulk ablation model is established，taking deposition reaction，gas erosion and expansion phenomena into account. The porous medium zone and the solid zone are solved separately and interface temperature coupling numerical method is used. The numerical calculations for ablation experiments in gas phase environment are carried out，the main influence factors of the carbon layer pore structure and the mass ablation rate are analyzed. The computational results agreed well with the experimental ones. The speed magnitude of ablating gas in carbon layer is about millimeter to centimeter pre second，the relative pressure magnitude is about 103 ~ 104Pa，and the relative pressure distribution in carbon layer is also obtained.

Key words: Solid rocket motor；Ablation model；Deposition reaction；Gas erosion；Expansion；Porous structure；Ablating gas

王书贤,李江,蔡霞. 气相环境下EPDM绝热材料双区体烧蚀模型[J]. 推进技术, 2016, 37(2): 378-385.

WANG Shu-Xian¹,LI Jiang²,CAI Xia¹. Bulk Ablation Model with Double Zones for EPDM[J]. Journal of Propulsion Technology, 2016, 37(2): 378-385.

参考文献

[1] Robert T Swann. Numerical Analysis of the Transient Response of Advanced Thermal Protection Systems for Atmospheric Entry[R]. NASA TN D-1370, 1962.
[2] George Y Jumper. Thermomechanical Ablation[R]. AD-A021 275, 1975.
[3] Torre L, Kenny J M, Maffezzoli A M. Degradation Behavior of a Composite Material for Thermal Protection Systems Part III-Experimental Characterization[J]. Journal of Materials Science, 35(18): 4563-4566.
[4] 王书贤, 何国强, 李江, 等. 单纯热化学烧蚀环境下EPDM绝热材料炭化层结构特征分析[J]. 固体火箭技术, 2010, 33(2): 214-117.
[5] Yang B C, Cheung F B, Koo J H. Modeling of One-Dimensional Thermo Mechanical Erosion of the High-Temperature Ablatives[J]. Journal of Applied Mechanics, 1993, 60: 1027-1032.
[6] Dimitrienko Yu I. Effect of Thermomechanical Erosion of Heterogeneous Combustion of Composite Materials in High-Speed Flows[J]. Combustion and Flame,2000, 122: 211-226.
[7] Curry D M, Tillian D J. Apollo Thermal Protection System Revisited[R]. National Space & Missile Materials Symposium, 2006, 26-30.
[8] 李强, 杨飒, 李江, 等. EPDM绝热材料耦合烧蚀模型[J]. 固体火箭技术, 2012, 35(1): 114-117.
[9] 杨飒, 何国强, 李江, 等. 炭化层疏松／致密结构的三元乙丙烧蚀模型[J]. 航空动力学报, 2012, 27(5): 1172-1178.
[10] Reynolds R A, Russell G W, Nourse R W. Ablation Performance Characterization of Thermal Protection Material Using a Mach 4. 4 Sled Test[R]. AIAA 92-3055.
[11] Gerald Wayne Russell. Analytic Modeling and Experimental Validation of Intumescent Behavior of Charring Heat Shield Materials[D]. Alabama: The University of Alabama in Huntsville, 2002.
[12] Lewis D, Anderson L. Effects of Melt-Layer Formation on Ablative Materials Exposed to Highly Aluminized Rocket Motor Plumes[R]. AIAA 98-0872.
[13] Zien T F. Application of Heat Balance Integra Method to Droplet Freezing in Melting Ablation[R]. AIAA 2004-167.
[14] 李江, 刘佩进, 陈剑, 等. 冲蚀条件下炭布橡胶绝热层烧蚀实验与计算[J]. 固体火箭技术, 2006, 29(2): 110-112.
[15] William Kays, Michael Crawford, Bernhard Weigand. Convective Heat and Mass Transfer[M]. USA: McGraw-Hill Inc., 1993.
[16] 王书贤, 何国强, 刘佩进, 等. 气相燃气速度对EPDM绝热材料烧蚀的影响[J]. 推进技术, 2010, 31(2): 235-239. (WANG Shu-xian, HE Guo-qiang, LIU Pei-jin, et al. The Influence of Gas-Phase Speed on EPDM Insulator Ablation[J]. Journal of Propulsion Technology, 2010, 31(2): 235-239.)
[17] Clark R K. An Analysis of a Charring Ablator with Thermal Nonequilibrium Chemical Kinetics and Mass Transfer[R]. NASA-TN-D-7180.
[18] Ayasoufi A, Rahmani R K, Cheng G, et al. Numerical Simulation of Ablation for Reentry Vehicles[R]. AIAA 2006-2908.
[19] 刘洋, 李江, 何国强, 等. 颗粒冲刷条件下三元乙丙绝热材料烧蚀特性实验[J]. 推进技术, 2010, 31(5): 612-617. (LIU Yang, LI Jiang, HE Guo-qiang, et a1. Experiment on Ablation Characteristic of EPDM Insulator under Particles Erosion Condition[J]. Journal of Propulsion Technology, 2010, 31(5): 612-617.)　*　收稿日期:2014-10-29；修订日期:2014-12-31。基金项目:西安市科技计划项目(CXY1518(5))。作者简介:王书贤,女,博士,讲师,研究领域为发动机热防护。E-mail: wangshuxian1977@sina.com(编辑:史亚红)