套筒配合间隙对燃烧室出口温度场品质的影响

推进技术 ›› 2016, Vol. 37 ›› Issue (6): 1015-1021.

套筒配合间隙对燃烧室出口温度场品质的影响

江立军,曹俊,严明超,王利,邬俊,宋阁

中国航空动力机械研究所，湖南株洲 412002,中国航空动力机械研究所，湖南株洲 412002,中国航空动力机械研究所，湖南株洲 412002,中国航空动力机械研究所，湖南株洲 412002,中国航空动力机械研究所，湖南株洲 412002,中国航空动力机械研究所，湖南株洲 412002

发布日期:2021-08-15
作者简介:江立军，男，博士，工程师，研究领域为航空发动机燃烧室。

Effects of Gap Height between Sleeve and Baffle on

China Aviation Powerplant Research Institute，Zhuzhou 412002，China,China Aviation Powerplant Research Institute，Zhuzhou 412002，China,China Aviation Powerplant Research Institute，Zhuzhou 412002，China,China Aviation Powerplant Research Institute，Zhuzhou 412002，China,China Aviation Powerplant Research Institute，Zhuzhou 412002，China and China Aviation Powerplant Research Institute，Zhuzhou 412002，China

Published:2021-08-15

摘要/Abstract

摘要： 为了研究燃烧室头部涡流器套筒与冷却片配合间隙对燃烧室出口温度场品质的影响规律，分别针对0.1mm，0.15mm及0.2mm三种不同间隙宽度情况进行了燃烧室性能试验研究，并采用数值模拟方法对其影响机理进行了分析。结果表明，通过间隙的环状射流对涡流器旋转射流方向、燃烧室主燃区流场结构以及燃油质量分布均有较大影响。随着间隙宽度增加，燃烧室出口温度分布系数增加了29%，径向温度分布曲线的高温点向叶根方向的移动距离超过10%叶片高度，燃烧室出口温度场品质急剧恶化。

关键词: 航空航天推进系统；燃气涡轮发动机；燃烧室；出口温度场

Abstract: In order to understand how the gap between sleeve and baffle affecting the property of combustor exit temperature distribution，an experimental investigation has been carried out to test an annular combustor exit temperature distribution at different gap height，viz. 0.1mm，0.15mm and 0.2mm. The mechanism of gap effect is also analyzed by numerical simulation method. Numerical simulation results revealed that swirl flow direction，primary zone flow structure and mass fraction distribution of kerosene were strongly affected by annular jet from the gap between sleeve and baffle. The experimental and computational results show that combustor exit temperature distribution property is deteriorated while the gap height exceeds the design value. The overall temperature distribution factor (OTDF) increases by 29% and the high temperature point on the radial temperature distribution curve migrates inward more than 10% guide vane height with the increase of gap height.

Key words: Aerospace propulsion system；Gas turbine engine；Combustor；Exit temperature distribution

江立军,曹俊,严明超,王利,邬俊,宋阁. 套筒配合间隙对燃烧室出口温度场品质的影响[J]. 推进技术, 2016, 37(6): 1015-1021.

JIANG Li-jun,CAO Jun,YAN Min-chao,WANG Li,WU Jun,SONG Ge. Effects of Gap Height between Sleeve and Baffle on[J]. Journal of Propulsion Technology, 2016, 37(6): 1015-1021.

参考文献

[1] Lefebvre A H, Ballal D R. Gas Turbine Combustion- Alternative Fuels and Emissions[M]. Philadelphia: Taylor-Francis, 2010.
[2] 李尚维. 燃烧室头部部件几何特性对温度场的影响[J]. 燃气涡轮试验与研究, 1996, (2): 21-28.
[3] 彭云晖, 林宇震, 刘高恩. 三旋流器燃烧室出口温度分布的初步试验研究[J]. 航空动力学报, 2007, 22(4): 554-560.
[4] Norgren C T, Humenik F M. Dilution-Jet Mixing Study for Gas-Turbine Combustors[R]. NASA TND-4695, 1968.
[5] Widener S K. Improving the Development Process for Main Combustor Exit Temperature Distribution[R]. AIAA 89-2804.
[6] 张征, 杨阳, 樊未军, 等. 掺混孔参数影响燃烧室出口温度场的计算方法[J]. 燃烧科学与技术, 2006, 12(6): 502-506.
[7] 顾铭企. 燃烧室进口流场畸变对出口温度场品质影响的试验研究[J]. 航空发动机, 1994, (2): 1-11.
[8] Bishop C K, Allan W. Effects of Fuel Nozzle Condition on Gas Turbine Combustion Chamber Exit Temperature Distributions[R]. ASME GT-2010-23441.
[9] Lefebvre A H. Fuel Effects on Gas Turbine Combustion—Liner Temperature, Pattern Factor and Pollutant Emissions[J]. Journal of Aircraft, 1984, 21(11): 887-898.
[10] 刘存喜, 段冬霞, 毛艳辉, 等. 排气弯管结构参数对回流环形燃烧室出口温度分布的影响[J]. 燃气轮机技术, 2011, 24(4): 17-21
[11] 顾铭企. 燃烧室出口温度场品质的研究[J]. 航空发动机, 1992, (3): 1-9.
[12] 丁毅生, 林秀荣. 统计推算燃烧室出口热点温度的优化方法[J]. 航空动力学报, 1993, 8(3): 259-262.
[13] 刘庆国. 长期运行后燃烧室出口温场品质变化的试验考察[J]. 航空发动机, 1996, (2): 54-59.
[14] 程新荣, 张宝诚. 航空发动机燃烧室出口温度场稳定性的研究[J]. 沈阳航空工业学院学报, 2003, 20(4): 1-4.
[15] 张树林, 杨宝兴, 王洪斌, 等. 航空发动机涡轮前温度场数据分析方法[J]. 航空发动机, 2007, 33(4): 23-26.
[16] MCdonell V G, Arellano L, Lee S W, et al. Effect of Hardware Alignment on Fuel Distribution and Combustion Performance for a Production Engine Fuel Injection Assembly[C]. Pittsburgh: Twenty-Sixth Symposium (International) on Combustion/The Combustion Institute, 1996: 2725-2732.
[17] Rudrapatna N S, Bohman R R, Anderson J K, et al. The Influence of Manufacturing Tolerances on Swirler Durability[R]. ASME GT-2014-26058.
[18] Bradsahw S, Waitz I. Impact of Manufacturing Variability on Combustor Liner Durability[R]. ASME GT-2006-91098.
[19] 胡好生, 赵坚行, 钟建平, 等. 一种新颖的燃烧室出口温度场调试方法[J]. 航空动力学报, 2007, 22(8): 1222-1226.
[20] 宋双文, 蒋荣伟, 陈剑, 等. 离心甩油折流环形燃烧室的性能试验[J]. 航空动力学报, 2007, 22(9): 1401-1404.
[21] 蔡文祥, 赵坚行, 张靖周. 带圆筒头部火焰筒两相燃烧流场及性能计算[J]. 推进技术, 2007, 28(2): 122-126. (CAI Wen-xiang, ZHAO Jian-xing, ZHANG Jing-zhou. Numerical Study of Two-Phase Field and Combustion Performance in Annual Combustor with Cylindrical Heads[J]. Journal of Propulsion Technology, 2007, 28 (2): 122-126.)　　　　　　　　　　　　　*　收稿日期:2014-12-31；修订日期:2015-04-27。作者简介:江立军,男,博士,工程师,研究领域为航空发动机燃烧室。E-mail: jiang0604102@126.com(编辑:梅瑛)