粗糙度对压气机叶栅损失特性影响的实验研究

推进技术 ›› 2016, Vol. 37 ›› Issue (7): 1263-1270.

粗糙度对压气机叶栅损失特性影响的实验研究

高磊^1,2,王子楠^1,2,耿少娟¹,张宏武¹,聂超群¹

中国科学院工程热物理研究所，先进能源动力重点实验室，北京 100190; 中国科学院大学，北京 100190,中国科学院工程热物理研究所，先进能源动力重点实验室，北京 100190; 中国科学院大学，北京 100190,中国科学院工程热物理研究所，先进能源动力重点实验室，北京 100190,中国科学院工程热物理研究所，先进能源动力重点实验室，北京 100190,中国科学院工程热物理研究所，先进能源动力重点实验室，北京 100190

发布日期:2021-08-15
作者简介:高磊，男，硕士生，研究领域为叶轮机械气动热力学。
基金资助:
中国科学院重点部署项目(KGZD-EW-302-3)。

Experimental Study for Effects of Surface Roughness on Compressor Cascade Loss Characteristics

Key Laboratory of Advanced Energy and Power，Institute of Engineering Thermophysics，Chinese Academy of Sciences，Beijing 100190，China; University of Chinese Academy of Sciences，Beijing 100190，China,Key Laboratory of Advanced Energy and Power，Institute of Engineering Thermophysics，Chinese Academy of Sciences，Beijing 100190，China; University of Chinese Academy of Sciences，Beijing 100190，China,Key Laboratory of Advanced Energy and Power，Institute of Engineering Thermophysics，Chinese Academy of Sciences，Beijing 100190，China,Key Laboratory of Advanced Energy and Power，Institute of Engineering Thermophysics，Chinese Academy of Sciences，Beijing 100190，China and Key Laboratory of Advanced Energy and Power，Institute of Engineering Thermophysics，Chinese Academy of Sciences，Beijing 100190，China

Published:2021-08-15

摘要/Abstract

摘要： 为了研究粗糙度对压气机叶栅损失特性的影响，采用实验方法研究了三种雷诺数条件下表面粗糙度量级和位置对压气机平面叶栅不同攻角下总压损失特性的影响。叶片表面粗糙度通过贴砂纸的方式改变。对每种雷诺数，定量考察了由叶片表面贴砂纸引起的叶片厚度变化对叶栅攻角-损失特性的影响；对整体粗糙叶片，分析了四种粗糙度量级的影响；讨论了叶片表面局部粗糙度位置的影响。研究表明，定量比较损失时需考虑贴砂纸引起的叶片厚度变化，以加厚光滑叶片作为比较基准。粗糙度量级和位置对叶栅损失特性的影响与雷诺数密切相关，其影响趋势和程度在不同攻角范围内表现出明显的差异。高Re数条件下，当无量纲粗糙度[k+≤14.6]时，叶栅性能尚可接受，当[k+≥20.1]时，可认为叶栅已基本失效。总体上，叶片前缘和吸力面粗糙度对损失变化的影响最大。Re=[1.0×105]，-0.6°攻角情况下整体和吸力面前部加粗糙度80μm时，总压损失值相比加厚光滑叶片分别降低了17.3%和23.1%。

关键词: 压气机叶栅；总压损失；粗糙度量级；粗糙度位置；雷诺数；攻角

Abstract: In order to study the effects of surface roughness， the effects of surface roughness magnitudes and location on total pressure loss characteristics of a planar compressor cascade at three Reynolds numbers and different incidence angles were studied experimentally. Blade surface roughness was changed by sticking sandpapers. For each Reynolds number，firstly，the effects of blade thickness variation induced by sticking sandpaper on cascade total pressure loss - incidence angles characteristics were quantitatively investigated. Then，for the entire roughened blade，the impacts of four kinds of roughness magnitudes were analyzed. Furthermore，the influence of blade surface partial roughness location was discussed. The results show that the changes of blade thickness induced by sticking sandpapers should be included in the quantitative comparison of cascade loss，in this paper the comparisons are made on the base of the thickened smooth cascade. The impacts of roughness magnitudes and location on cascade total pressure loss characteristics are closely related with Reynolds numbers，the trend and magnitude within different incidence angles show obvious difference. Under conditions of high Re number，the cascade performance is acceptable if the value of nondimensional roughness[k+] is less than 14.6，and the cascade can be considered to be almost failed if the value of [k+] is more than 20.1. On a whole，roughness around the leading edge and on the suction surface contributes most to the change of blade total pressure loss. The values of total pressure loss are decreased by 17.3% and 23.1%，respectively，compared with the case of the thickened smooth cascade at Re number of [1.0×105] and incidence angle of -0.6°，when the roughness magnitude of 80μm is imposed on blade entire and suction front portion surface respectively.

Key words: Compressor cascade；Total pressure loss；Roughness magnitude；Roughness location；Reynolds number；Incidence angle

高磊,王子楠,耿少娟,张宏武,聂超群. 粗糙度对压气机叶栅损失特性影响的实验研究[J]. 推进技术, 2016, 37(7): 1263-1270.

GAO Lei^1,2,WANG Zi-nan^1,2,GENG Shao-juan¹,ZHANG Hong-wu¹,NIE Chao-qun¹. Experimental Study for Effects of Surface Roughness on Compressor Cascade Loss Characteristics[J]. Journal of Propulsion Technology, 2016, 37(7): 1263-1270.

参考文献

[1] 陈绍文, 张辰, 石慧, 等. 轴流压气机级内污垢沉积影响的数值研究[J]. 推进技术, 2012, 33(3): 377-383. (CHEN Shao-wen, ZHANG Chen, SHI Hui, et al. Numerical Study on the Impact of Fouling on Axial Compressor Stages[J]. Journal of Propulsion Technology, 2012, 33(3): 377-383.)
[2] Diakunchak I S. Performance Deterioration in Industrial Gas Turbines[J]. Journal of Engineering for Gas Turbines and Power, 1992, 114(2): 161-168.
[3] Meher-Homji C B, Chaker M, Bromley A F. The Fouling of Axial Flow Compressors-Causes, Effects, Susceptibility and Sensitivity[R]. ASME 2009-GT-59239.
[4] 李本威, 李冬, 李姜华, 等. 单级压气机性能衰退定量研究[J]. 航空动力学报, 2010, 25(7): 1588-1594.
[5] 李冬, 樊照远, 张娟, 等. 压气机叶片粗糙度对其性能衰退的影响研究[J]. 航空发动机, 2009, 35(5): 32-35.
[6] Bammert K, Woelk G U. The Influence of the Blading Surface Roughness on the Aerodynamic Behavior and Characteristic of an Axial Compressor[J]. Journal of Engineering for Gas Turbines and Power, 1980, 102(2): 283-287.
[7] Back S C, Jeong I C, Sohn J L, et al. Influence of Surface Roughness on the Performance of a Compressor Blade in a Linear Cascade: Experiment and Modeling [R]. ASME 2009-GT -59703.
[8] Back S C, Sohn J H, Song S J. Impact of Surface Roughness on Compressor Cascade Performance [J]. Journal of Fluids Engineering, 2010, 132(6): 064502-064502-6.
[9] Nikuradse J. Laws for Flows in Rough Pipes[R]. NACA TM 1292, 1950.
[10] White F M. Viscous Fluid Flow[M]. New York: McGraw-Hill, 1991.
[11] Schlichting H. Boundary Layer Theory [M]. New York: McGraw-Hill, 1979.
[12] Suder K L, Chima R V, Strazisar A J, et al. The Effect of Adding Roughness and Thickness to a Transonic Axial Compressor Rotor [J]. Journal of Turbomachinery, 1995, 117(4): 491-505.
[13] Back S C, Hobson G V, Song S J, et al. Effects of Reynolds Number and Surface Roughness Magnitude and Location on Compressor Cascade Performance[J].Journal of Turbomachinery, 2012, 134(5): 051013-051013-6.
[14] Leipold R, Boese M, Fottner L. The Influence of Technical Surface Roughness Caused by Precision Forging on the Flow Around a Highly Loaded Compressor Cascade[J]. Journal of Turbomachinery, 1999, 122(3): 416-424.
[15] 张波. 超高负荷低压涡轮叶片边界层分离与转捩控制研究[D]. 北京:中国科学院工程热物理研究所, 2012.
[16] Gbadebo S A, Hynes T P, Cumpsty N A. Influence of Surface Roughness on Three- Dimensional Separation in Axial Compressors[J]. Journal of Turbomachinery, 2004, 126(4) : 455-463.
[17] Speidel L. The Effect of Surface Roughness on the Flow Losses in Plane Blading Grids[J]. Forschung auf dem Gebiete des Ingenieurwesens, 1954, 20(5): 129-140.
[18] Koch C C, Smith L H. Loss Sources and Magnitudes in Axial-Flow Compressors[J]. Journal of Engineering for Gas Turbines and Power, 1976, 98(3): 411-424.
[19] Song S J, Sohn J L, Kim T S. Final Report on the Effects of Compressor Fouling on Gas Turbine Performance and Diagnosis[R]. Korea Midland Power, Technical Report R-2005-0 -016.
[20] 王子楠, 高磊, 耿少娟, 等. 不同端壁间隙下压气机平面叶栅角区流动的数值模拟和实验研究[C]. 西安:中国工程热物理学会学术会议, 2014.(编辑:史亚红)　　　　　　　　　　　　　*　收稿日期:2015-03-10；修订日期:2015-05-05。基金项目:中国科学院重点部署项目(KGZD-EW-302-3)。作者简介:高磊,男,硕士生,研究领域为叶轮机械气动热力学。E-mail: gaolei@iet.cn