旋转对涡轮叶片异型孔气膜冷却的影响

推进技术 ›› 2016, Vol. 37 ›› Issue (9): 1713-1719.

旋转对涡轮叶片异型孔气膜冷却的影响

朱兴丹,张靖周,谭晓茗

南京航空航天大学能源与动力学院，江苏省航空动力系统重点实验室，江苏南京 210016,南京航空航天大学能源与动力学院，江苏省航空动力系统重点实验室，江苏南京 210016,南京航空航天大学能源与动力学院，江苏省航空动力系统重点实验室，江苏南京 210016

发布日期:2021-08-15
作者简介:朱兴丹，男，博士生，研究领域为航空发动机热端部件冷却技术。
基金资助:
国家自然科学基金(U1508212)；江苏省研究生培养创新工程(KYLX_0307)；中央高校基本科研业务费专项资金；

Effects of Rotation on Shaped-Hole Film

Nanjing University of Aeronautics and Astronautics，Jiangsu Province Key Laboratory of Aerospace Power System，Nanjing 210016，China,Nanjing University of Aeronautics and Astronautics，Jiangsu Province Key Laboratory of Aerospace Power System，Nanjing 210016，China and Nanjing University of Aeronautics and Astronautics，Jiangsu Province Key Laboratory of Aerospace Power System，Nanjing 210016，China

Published:2021-08-15

摘要/Abstract

摘要： 为了揭示异型气膜孔在旋转状态下的冷却特性，采用数值模拟的方法分析了吹风比为0.6时旋转对涡轮叶片异型气膜孔流动及冷却的影响，包括三种气膜孔:圆孔、扇形孔及收敛缝型孔。结果表明:旋转时气膜射流受离心力和哥氏力作用朝叶尖方向偏转，射流涡结构被弱化而变得不明显，气膜射流向主流的穿透得到一定程度的削弱；圆孔和扇形孔冷却效率随旋转雷诺数增大而升高，局部最多可分别提高100%和50%左右，收敛缝型孔冷却效率受旋转雷诺数的影响较小；旋转状态下扇形孔冷却效果与收敛缝型孔相当，仍然优于圆孔。

关键词: 涡轮叶片；异型孔；气膜冷却；旋转雷诺数；数值模拟

Abstract: The effects of rotation on shaped-hole film flow and cooling on a turbine blade with a blowing ratio of 0.6 were investigated through numerical methods to figure out the cooling characteristics of shaped-holes with rotation，including the cylindrical hole，the fan-shaped hole and the converging slot-hole. The results show that the film jet deflects towards the blade tip due to the combined effects of centrifugal and Coriolis force derived from rotation. As a consequence，the integrated film vortex is weakened and becomes unconspicuous. Simultaneously，the penetration of the film jet to the mainstream is diminished to some extent. The cooling effectiveness improves with the increase of rotational Reynolds number with approximate regional 100% and 50% increment，respectively，with regard to the cylindrical hole and the fan-shaped hole whereas the converging slot-hole indicates a slight effect of the rotational Reynolds number on its cooling effectiveness. The fan-shaped hole is comparable to the converging slot-hole under rotational conditions where both outperform the cylindrical hole in terms of film cooling performance.

Key words: Turbine blade；Shaped-hole；Film cooling；Rotational Reynolds number；Numerical simulation

朱兴丹,张靖周,谭晓茗. 旋转对涡轮叶片异型孔气膜冷却的影响[J]. 推进技术, 2016, 37(9): 1713-1719.

ZHU Xing-dan,ZHANG Jing-zhou,TAN Xiao-ming. Effects of Rotation on Shaped-Hole Film[J]. Journal of Propulsion Technology, 2016, 37(9): 1713-1719.

参考文献

[1] Bunker R S. A Review of Shaped Hole Turbine Film Cooling Technology[J]. Journal of Heat Transfer, 2005, 127: 441-453.
[2] Lee K D, Kim K Y. Shape Optimization of a Fan-Shaped Hole to Enhance Film-Cooling Effectiveness[J].International Journal of Heat and Mass Transfer, 2010, 53: 2996-3005.
[3] Saumweber C, Schulz A. Effect of Geometry Variations on the Cooling Performance of Fan-Shaped Cooling Holes[J]. Journal of Turbomachinery, 2012, 134.
[4] 姚玉, 张靖周, 何飞, 等. 涡轮叶片吸力面上收敛缝形孔气膜冷却效率的数值研究[J]. 航空学报, 2010, 31(6): 1115-1120.
[5] 姚玉, 张靖周, 何飞, 等. 涡轮叶片吸力面上收敛缝形孔气膜冷却对叶栅气动损失的影响[J]. 航空学报, 2010, 31(7): 1312-1317.
[6] Yao Y, Zhang J Z. Investigation on Film Cooling Characteristics from a Row of Converging Slot-Holes on Flat Plate[J]. Science China Technology Science, 2011, 54: 1793-1800.
[7] Yao Y, Zhang J Z, Wang L P. Film Cooling on a Gas Turbine Blade Suction with Converging Slot-Hole[J]. International Journal of Thermal Science, 2013, 65: 267-279.
[8] Liu C L, Zhu H R, Bai J T, et al. Film Cooling Performance of Converging Slot-Hole Rows on a Gas Turbine Blade[J]. International Journal of Heat and Mass Transfer, 2010, 53: 5232-5241.
[9] Takeishi K, Aoki S, Sato T, et al. Film Cooling on a Gas Turbine Rrotor Blade[J]. Journal of Turbomachinery, 1992, 114: 828-834.
[10] Yuan F, Zhu X C, Du Z H. Experimental Investigation for the Effect of Rotation on Three-Dimensional Flow Field in Film-Cooled Turbine[J]. Chinese Journal of Mechanical Engineering, 2007, 20(1): 10-15.
[11] 李国庆, 邓宏武, 肖俊. 旋转状态涡轮叶片吸力面单孔气膜冷却实验[J]. 航空动力学报, 2010, 25(4): 780-785.
[12] 李国庆, 邓宏武, 肖俊. 旋转状态下涡轮叶片压力面气膜冷却特性[J]. 北京航空航天大学学报, 2010, 36(11): 1286-1290.
[13] 丁水汀, 王伟, 杨彬. 旋转状态下气膜冷却偏转理论的实验研究[J]. 推进技术, 2010, 31(4): 599-606. (DING Shui-ting, WANG Wei, YANG Bin. Experimental Study of Deflective Theory of Film Cooling Trajectory under Rotating Operating Conditions[J]. Journal of Propulsion Technology, 2010, 31(4): 599-606.)
[14] Garg V K. Adiabatic Effectiveness and Heat Ttransfer Coefficient on a Film-Cooled Rotating Blade[J]. Numerical Heat Transfer, 1997, 32(8): 811-830.
[15] Garg V K. Heat Transfer on a Film-Cooled Rotating Blade Using Different Turbulent Models[J]. International Journal of Heat and Mass Transfer, 1999, 42(5):789-802.
[16] Garg V K. Heat Transfer on a Film-Cooled Rotating Blade[J]. International Journal of Heat and Fluid Flow, 2000, 21(2): 134-145.
[17] Zhang C Z, Hassan I. Simulation of a Louver Cooling Scheme on a Rotating Turbine Blade[J]. International Journal of Numerical Methods for Heat & Fluid Flow,2012, 22(5): 622-640.
[18] 刘宁, 孙纪宁. 旋转对气膜冷却影响的大涡模拟[J]. 推进技术, 2011, 32(2): 245-252. (LIU Ning, SUN Ji-ning. Large Eddy Simulation of the Effect of Rotation on Film Cooling[J]. Journal of Propulsion Technology, 2011, 32(2): 245-252.)
[19] 刘宁, 孙纪宁. 不同来流条件下旋转对气膜冷却的影响[J]. 推进技术, 2011, 32(5): 706-712. (LIU Ning, SUN Ji-ning. Effect of Rotation on Film Cooling Under Different Inflow Conditions[J]. Journal of Propulsion Technology, 2011, 32(5): 706-712.)
[20] 朱兴丹, 谭晓茗, 郭文, 等. 高压涡轮转子叶片内部气流组织方式研究[J]. 航空学报, 2014, 35(12): 3273-3282.
[21] Ahn J, Schobeiri M T, Han J C, et al. Film Cooling Effectiveness on the Leading Edge Region of a Rotating Turbine Blade with Two Rows of Film Cooling Holes Using Pressure Sensitive Paint[J]. Journal of Heat Transfer, 2006, 128: 879-888.(编辑:朱立影)　　　　　　　　　　　　　*　收稿日期:2015-04-15；修订日期:2015-06-12。基金项目:国家自然科学基金(U1508212)；江苏省研究生培养创新工程(KYLX_0307)；中央高校基本科研业务费专项资金；江苏省航空动力系统重点实验室开放课题(NJ20130026)。作者简介:朱兴丹,男,博士生,研究领域为航空发动机热端部件冷却技术。E-mail: zxdljll@163.com