旋转楔形通道流动与换热特性的数值研究

推进技术 ›› 2017, Vol. 38 ›› Issue (1): 125-133.

旋转楔形通道流动与换热特性的数值研究

刘涛¹,李洋²

中国航空动力机械研究所，湖南株洲 412002,北京航空航天大学能源与动力工程学院航空发动机气动热力国家级重点实验室，北京 100191

发布日期:2021-08-15
作者简介:刘涛，女，硕士生，研究领域为叶轮机械流动与涡轮叶片内部流动换热。

Numerical Investigation of Flow and Heat Transfer Characteristics in a Rotating Wedge-Shape Channel

AVIC Aviation Powerplant Research Institute，Zhuzhou 412002，China and National Key Laboratory of Science and Technology on Aero-Engine Aero-thermodynamics， School of Energy and Power Engineering，Beihang University，Beijing 100191，China

Published:2021-08-15

摘要/Abstract

摘要： 为了模拟涡轮叶片尾缘冷却通道的流动换热特性，建立了带侧向出流的旋转楔形冷却通道的数值模型，采用k-ω SST两方程模型研究了流动与旋转对于楔形通道内换热分布与不同出口冷气出流比例的影响。在静止情况下，由于沿程侧向的冷气出流，换热沿程降低。而旋转压缩了通道顶部内侧区域的流动滞止涡，导致内侧区域的换热显著增强。静止情况下沿程冷气出流占比不断提高，但雷诺数的影响有限。随着旋转数的提高，通道冷气出流比例受到旋转离心力的主导作用，前半段冷气出流比例下降，后半段出流比例上升，在50%径向高度位置为平均值。在大旋转数下(Ro>0.4)，通道前半段冷气出流比例逐渐下降为0。通道安装角度的变化对冷气出流比例的影响有限。

关键词: 尾缘；冷却通道；出流比例；旋转换热；数值研究

Abstract: In order to simulate flow and heat transfer characteristics in turbine blade trailing edge cooling channel，a numerical rotating wedge-shape channel with lateral coolant extraction was modeled. The standard k-ω SST turbulence model was applied for the simulation that focused on the flow and rotation factors on the heat transfer distribution and coolant extraction ratios in wedge-shape channel. At stationary case，the heat transfer level decreases along the channel due to the lateral flow extraction. But rotation compresses the end-wall vortex of the inner corner which causes higher heat transfer of the inner section. The coolant extraction ratio increases from the channel entrance to the end-wall at stationary. And the Reynolds number shows very limited influence. As the rotation number increases，the centrifugal force dominates the coolant extraction ratio. Less coolant are observed for the outlets near the channel entrance and more coolant flow through the down-stream outlets. At 50% radial location，it shows the average extraction ratio. Even more，the coolant mass flow rate ratio gradually decreases to 0 at high rotation number(Ro>0.4). It is also found that the channel orientation shows limited effect on the coolant extraction ratio.

Key words: Trailing edge；Cooling channel；Coolant extraction ratio；Rotating heat transfer；Numerical investigation

刘涛,李洋. 旋转楔形通道流动与换热特性的数值研究[J]. 推进技术, 2017, 38(1): 125-133.

LIU Tao¹,LI Yang². Numerical Investigation of Flow and Heat Transfer Characteristics in a Rotating Wedge-Shape Channel[J]. Journal of Propulsion Technology, 2017, 38(1): 125-133.

参考文献

[1] Han J C. Turbine Blade Cooling Studies at Texas A&M University: 1980-2004[J]. Journal of Thermophysics and Heat Transfer, 2006, 20(2): 161-187.
[2] 倪萌, 朱惠人, 裘云, 等. 航空发动机涡轮叶片冷却技术综述 [J]. 燃气轮机技术, 2006, 18(4): 25-33.
[3] 阚瑞, 迟重然, 杨力, 等. 燃气轮机高温叶片内部冷却技术概述 [J]. 热力透平, 2013, 42(4): 260-264.
[4] 刘钊, 杨星, 丰镇平, 燃气轮机透平叶片传热和冷却研究: 内部冷却 [J]. 热力透平, 2013, 42(4): 265-275.
[5] Han J C, Fundamental Gas Turbine Heat Transfer[J]. Journal of Thermal Science and Engineering Applications, 2013, 5(2).
[6] Qiu L, Deng H, Tao Z, Effect of Channel Orientation in a Rotating Smooth Wedge-Shaped Cooling Channel with Lateral Ejection [R]. ASME 2013-GT-94758.
[7] Wright L M, Liu Y -H, Han J C, et al. Heat Transfer in Trailing Edge, Wedge-Shaped Cooling Channels under High Rotation Numbers [J]. Journal of Heat Transfer, 2008, 130(7).
[8] Liu Y -H, Huh M, Wright L M, et al. Heat Transfer in Trailing Edge, Wedge Shaped Cooling Channels with Slot Ejection under High Rotation Numbers[R]. ASME 2008-GT-50343.
[9] Liu Y -H, Huh M, Han J C. High Rotation Number Effect on Heat Transfer in a Trailing Edge Channel with Tapered Ribs[J]. International Journal of Heat and Fluid Flow, 2012, 33(1): 182-192.
[10] Rallabandi A P, Liu Y -H, Han J C. Heat Transfer in Trailing Edge Wedge-Shaped Pin-Fin Channels with Slot Ejection under High Rotation Numbers[J]. Journal of Thermal Science and Engineering Applications, 2011, 3(2).
[11] Chang S W, Liou T -M, Chiou S F, et al. Heat Transfer in High-Speed Rotating Trapezoidal Duct with Rib-Roughened Surfaces and Air Bleeds from the Wall on the Apical Side[J]. Journal of Heat Transfer, 2008, 130(6).
[12] Qiu L, Deng H W, Tao Z. Effect of Channel Orientation in a Rotating Wedge-Shaped Cooling Channel with Pin Fins and Ribs [R]. ASME 2012-GT-68439.
[13] Tao Z, Qiu L, Deng H W. Heat Transfer in a Rotating Smooth Wedge-Shaped Channel with Lateral Fluid Extraction[J]. Applied Thermal Engineering, 2015, 87: 47-55.
[14] 陈豪, 邓宏武, 李洋, 等. 高旋转数下45°斜肋回转通道平均换热特性研究[J]. 推进技术, 2015, 36(9): 1339-1346. (CHEN Hao, DENG Hong-wu, LI Yang, et al. Heat Transfer in Rotating Two-Pass Square Duct with 45° Ribbed Walls under High Rotation Numbers[J]. Journal of Propulsion Technology, 2015, 36(9): 1339-1346.)
[15] 赵曙, 朱惠人, 郭涛, 等. 旋转带肋回转通道换热实验研究[J]. 推进技术, 2015, 36(6): 899-906. (ZHAO Shu, ZHU Hui-ren, Guo Tao, et al. Experimental Investigation of Heat Transfer for Rotating Internal Cooling Channels with Rib Turbulators[J]. Journal of Propulsion Technology, 2015, 36(6): 899-906.)
[16] Srinivasan B, Dhamarla A, Jayamurugan C, et al. Numerical Studies on Effect of Channel Orientation in a Rotating Smooth Wedge-Shaped Cooling Channel[R]. ASME 2014-GT-26560.
[17] Chung H, Park J S, Sohn H S, et al. Trailing Edge Cooling of a Gas Turbine Blade with Perforated Blockages with Inclined Holes[J]. International Journal of Heat and Mass Transfer, 2014, 73: 9-20.
[18] Siw S C, Chyu M K, Alvin M A. Trailing Edge Cooling of Gas Turbine Airfoil Using Blockages with Straight and Inclined Holes[R]. ASME 2014-GT-27081.
[19] Liu J, Weaver A, Shih T I, et al. Flow and Heat Transfer in a Triple-Impingement Configuration for Trailing-Edge Cooling[R]. ASME 2012-GT-70075.
[20] Liu J. Conjugate CFD Analysis of Three Trailing-Edge Cooling Configurations[D]. West Lafayette, Indiana: Purdue University, 2013.
[21] Pascotto M, Armellini A, Casarsa L, et al. Effects of Rotation and Channel Crientation on the Flow Field inside a Trailing Edge Internal Cooling Channel[R]. ASME 2012-GT-68050.
[22] Pascotto M, Armellini A, Casarsa L, et al. Numerical Aero-Thermal Analysis of a Rib-Roughened Trailing Edge Cooling Channel at Different Rotation Numbers and Channel Orientations[R]. ASME 2014-GT-25479.
[23] Armellini A, Casarsa L, Mucignat C. Flow Field Analysis inside a Gas Turbine Trailing Edge Cooling Channel under Static and Rotating Conditions[J]. International Journal of Heat and Fluid Flow, 2011, 32(6): 1147-1159.
[24] Dutta S, Andrews M J, Han J C, Prediction of Turbulent Heat Transfer in Rotating Smooth Square Ducts [J].International Journal of Heat and Mass Transfer, 1996, 39(12): 2505-2514.
[25] 曹玉璋, 陶智, 徐国强, 等. 航空发动机传热学[M]. 北京:北京航空航天大学出版社, 2005.　　　　　　　　　　　　　*　收稿日期:2015-07-08；修订日期:2015-10-29。作者简介:刘涛,女,硕士生,研究领域为叶轮机械流动与涡轮叶片内部流动换热。E-mail: buaalzw@126.com(编辑:张荣莉)