来流边界层对压气机平面叶栅角区流动的影响

推进技术 ›› 2017, Vol. 38 ›› Issue (1): 54-60.

来流边界层对压气机平面叶栅角区流动的影响

王子楠^1,2,耿少娟¹,张宏武¹

中国科学院工程热物理研究所，北京 100190; 中国科学院大学，北京 100190,中国科学院工程热物理研究所，北京 100190,中国科学院工程热物理研究所，北京 100190

发布日期:2021-08-15
作者简介:王子楠，男，博士生，研究领域为叶轮机械气动热力学。
基金资助:
中国科学院重点部署项目(KGZD-EW-302-3)。

Effects of Inlet Boundary Layer on Corner Flow in a Linear Compressor Cascade

Institute of Engineering Thermophysics，Chinese Academy of Sciences，Beijing 100190，China; University of Chinese Academy of Sciences，Beijing 100190，China,Institute of Engineering Thermophysics，Chinese Academy of Sciences，Beijing 100190，China and Institute of Engineering Thermophysics，Chinese Academy of Sciences，Beijing 100190，China

Published:2021-08-15

摘要/Abstract

摘要： 为更准确地预测压气机静叶角区失速以及为角区流场优化提供理论支持，在压气机平面叶栅环境下，利用数值模拟和实验验证方法，研究来流边界层厚度变化对角区流场及角区失速特性的影响。在角区失速前后的典型工况，利用总压损失系数和折转角的展向分布显示不同流场结构引起的性能变化；利用表面极限流线、总压损失云图和Q判据等手段显示角区涡结构特点。结果表明，当来流边界层厚度从1%展长增加到25%展长时，角区失速提前3°攻角发生，叶栅低损失工作范围缩减近30%。而在角区失速发生后，来流边界层厚度变化对角区失速结构没有明显影响，但仍会增强叶栅内其他区域的二次流效应。

关键词: 压气机；平面叶栅；来流边界层；角区失速

Abstract: To give a better prediction of compressor stator corner stall and provide theoretical support for corner flow optimization，the numerical simulation and experimental validation are utilized to investigate the effects of inlet boundary layer thickness variation on the corner flow structure and corner stall characteristics of a linear compressor cascade. At the typical conditions before and after corner stall，the spanwise distribution of total pressure loss coefficient and flow turning angle are analyzed to show the performance variation caused by different flow structures. Surface streamlines，total pressure loss coefficient contours and the Q criterion are used to show the feature of corner vortexes. Results show that the corner stall occurred 3° incidence angle ahead by increasing the inlet boundary thickness from 1% span to 25% span，which made the low-loss working range reduced by nearly 30%. After corner stall occurred，the increase of the inlet boundary layer thickness showed no obvious influence on corner stall structure，while it still strengthened the secondary flow effect at other blade passage space.

Key words: Compressor；Linear cascade；Inlet boundary layer；Corner stall

王子楠,耿少娟,张宏武. 来流边界层对压气机平面叶栅角区流动的影响[J]. 推进技术, 2017, 38(1): 54-60.

WANG Zi-nan^1,2,GENG Shao-juan¹,ZHANG Hong-wu¹. Effects of Inlet Boundary Layer on Corner Flow in a Linear Compressor Cascade[J]. Journal of Propulsion Technology, 2017, 38(1): 54-60.

参考文献

[1] Hirsch Ch. End-Wall Boundary Layers in Axial Compressors[J]. Journal of Engineering for Power, 1974, 96(4): 413-426.
[2] Horlock J H, Louis J F, Percival P M E, et al. Wall?Stall?in?Compressor Cascades[J]. Journal of Basic Engineering, 1966, 88(3): 637-648.
[3] Joslyn D H, Dring R P. Axial Compressor Stator Aerodynamics[J]. Journal of Engineering for Gas Turbines and Power, 1985, 107(3):485-493
[4] Dong Y, Gallimore S J, Hodson H P. Three Dimensional Flows and Loss Reduction in Axial Compressors[J]. Journal of Turbomachinery, 1987, 109(3): 354-361
[5] Gbadebo S A, Cumpsty N A, Hynes T P. Three-Dimensional Separations in Axial Compressors[J]. Journal of Turbomachinery, 2005, 127(2), 331-339
[6] 茅晓晨, 刘波, 曹志远, 等. 端壁射流对压气机叶栅角区分离控制的研究[J]. 推进技术, 2014, 35(12): 1615-1622. (MAO Xiao-chen, LIU Bo, CAO Zhi-yuan, et al. Research on Corner Separation Control for Compressor Cascade with End-Wall Jet Flow[J]. Journal of Propulsion Technology, 2014, 35(12): 1615-1622.)
[7] Wagner J H, Dring R P, Joslyn H D. Inlet Boundary Layer Effects in an Axial Compressor Rotor, Part I: Blade-to-Blade Effects[J]. Journal of Engineering for Gas Turbines and Power, 1985, 107(2): 374-380.
[8] 钟兢军, 刘毓国, 苏杰先, 等. 来流附面层厚度对弯叶片扩压叶栅损失的影响[J]. 工程热物理学报, 1997, 18(5): 553-557.
[9] 郭爽, 宋彦萍, 陆华伟, 等. 来流附面层对大转角扩压叶栅气动性能的影响[J]. 工程热物理学报, 2011, 32(10): 1661-1664
[10] 郭爽, 陆华伟, 宋彦萍, 等. 端壁附面层抽吸对大转角扩压叶栅旋涡影响的实验研究[J]. 推进技术, 2013, 34(11): 1466-1473. (GUO Shuang, LU Hua-wei, SONG Yan-ping, et al. Experimental Investigation on Effects of Endwall Boundary Layer Suction on Vortexes of High-Turning Compressor Cascades[J]. Journal of Propulsion Technology, 2013, 34(11): 1466-1473.)
[11] 陈绍文, 孙士珺, 兰云鹤, 等. 来流附面层对吸附式压气机叶栅影响的数值研究[J]. 机械工程学报, 2014, 50(24): 158-163.
[12] Brossman J R, Ball P R, Smith N R, et al. Sensitivity of Multistage Compressor Performance to Inlet Boundary Conditions[J]. Journal of Propulsion and Power, 2014, 30(2): 407-415.
[13] Hübner J, Fottner L. Influence of Tip-Clearance, Aspect Ratio, Blade Loading and Inlet Boundary on Secondary Losses in Compressor Cascades[R]. ASME GT- 96: 505.
[14] Sauer H, Schmidt R, Vogeler K. Influence of Chord Length and Inlet Boundary Layer on the Secondary Losses of Turbine Blades[J]. Journal of Turbomachinery, 2011, 134(1): 011015-1-9
[15] Lei V M, Spakovszky Z S, Greitzer E M. A Criterion for Axial Compressor Hub-Corner Stall[J]. Journal of Turbomachinery, 2008, 130(3): 031006-1-10.
[16] Zhang Y F, Mahallati A, Benner M. Experimental and Numerical Investigation of Corner Stall in a Highly-Loaded Compressor Cascade[R]. ASME GT-2014-27204.
[17] 王子楠, 高磊, 耿少娟, 等. 不同端壁间隙下压气机平面叶栅角区流动的数值模拟和实验研究[J]. 工程热物理学报, 2015, 36(7): 1428-1432.
[18] Schlichting H. ?Boundary Layer Theory[M]. USA: McGRAW-Hill Book, 1979. 　　　　　　　　　　　　　*　收稿日期:2015-06-29；修订日期:2015-08-28。基金项目:中国科学院重点部署项目(KGZD-EW-302-3)。作者简介:王子楠,男,博士生,研究领域为叶轮机械气动热力学。E-mail: wangzinan@iet.cn(编辑:田佳莹)