高转速下台阶篦齿流动特性的实验与计算

推进技术 ›› 2017, Vol. 38 ›› Issue (11): 2588-2596.

高转速下台阶篦齿流动特性的实验与计算

雷昭,孔晓治,刘高文,冯青

西北工业大学动力与能源学院，陕西西安 710072,西北工业大学动力与能源学院，陕西西安 710072,西北工业大学动力与能源学院，陕西西安 710072,西北工业大学动力与能源学院，陕西西安 710072

发布日期:2021-08-15
作者简介:雷昭，男，硕士生，研究领域为发动机空气系统和旋转盘腔中的流动传热。

Experimental and Numerical Investigations on Flow Characteristics of Stepped Labyrinth Seal at High Rotational Speed

School of Power and Energy，Northwestern Polytechnical University，Xi’an 710072，China,School of Power and Energy，Northwestern Polytechnical University，Xi’an 710072，China,School of Power and Energy，Northwestern Polytechnical University，Xi’an 710072，China and School of Power and Energy，Northwestern Polytechnical University，Xi’an 710072，China

Published:2021-08-15

摘要/Abstract

摘要： 对航空发动机压气机级间台阶篦齿封严进行了实验与计算研究。在不同压比(1.05～1.3)下，研究了转速(1.5～7.2kr/min)对篦齿的工作间隙变化、泄漏特性、温升特性和旋流特性的影响，并选取典型实验工况进行了数值模拟。研究表明实验结果与数值计算结果符合良好。随转速的增大，工作间隙减小，泄漏流量降低，两者最大降幅在40%左右；较小压比时流量系数微弱降低，较大压比时流量系数微弱增大。系统风阻温升随转速的增大而增大，且转速越大温升越快，最大温升为36K。另外，出口旋转盘腔同一径向位置的旋转比随转速的增大而增大，最大可达0.398；同一转速下，随出口旋转盘腔径向位置的增大，旋转比降低。

关键词: 压气机；级间封严；台阶篦齿；流量系数；风阻温升；旋转比

Abstract: Experimental and numerical investigations on stepped labyrinth seal in the aero-engine compressor stator well were carried out. The effects of rotational speed (1.5～7.2kr/min) on the variation of working tip clearance，sealing characteristics，windage heating characteristics and swirl characteristics were studied at different pressure ratios (1.05～1.3). In addition，numerical simulations were carried out under the typical experimental conditions. The results show that the numerical calculations agree well with the experimental data. With the increasing of rotational speed，the working tip clearance and the leakage mass flow decrease，and the largest reduction reaches about 40%. For low pressure ratios，the discharge coefficient decreases slightly，while the discharge coefficient increases slightly for high pressure ratios. Increasing the rotational speed leads to an increase in the system windage heating. The higher the rotational speed is，the faster the temperature rises，and the highest temperature rise reaches around 36K . Besides，by increasing the rotational speed，the swirl ratio at a specific radial location of the outlet disc cavity increases，which can be as high as 0.398. However，the swirl ratio shows a decrease with radius increasing in the outlet cavity at the same rotational speed.

Key words: Compressor；Stator well；Stepped labyrinth seal；Discharge coefficient；Windage heating；Swirl ratio

雷昭,孔晓治,刘高文,冯青. 高转速下台阶篦齿流动特性的实验与计算[J]. 推进技术, 2017, 38(11): 2588-2596.

LEI Zhao,KONG Xiao-zhi,LIU Gao-wen,FENG Qing. Experimental and Numerical Investigations on Flow Characteristics of Stepped Labyrinth Seal at High Rotational Speed[J]. Journal of Propulsion Technology, 2017, 38(11): 2588-2596.

参考文献

[1] 纪国剑. 航空发动机典型篦齿封严泄漏特性的数值和实验研究[D]. 南京:南京航空航天大学, 2008.
[2] 纪国剑, 吉洪湖. 台阶篦齿与衬套轴向位置和转速对封严特性影响的实验[J]. 航空动力学报, 2008, 23(3): 421-424.
[3] 王鹏飞, 郭文, 张靖周. 旋转封严篦齿风阻温升的试验研究与数值分析[J]. 航空动力学报, 2013, 28(6): 1402-1408.
[4] 王鹏飞, 刘玉芳, 郭文, 等. 高转速对直通型篦齿封严特性影响的试验研究[J]. 燃气涡轮试验与研究, 2007, 20(2): 45-48.
[5] 陈凯. 复杂参数影响下的级间封严流动特性和磨损特性研究[D]. 西安:西北工业大学, 2014.
[6] 吴丁毅. 台阶式篦齿封严特性的实验研究[J]. 流体机械, 1995, 23(11): 7-10.
[7] 吴丁毅. 直通式篦齿封严特性的实验研究[J]. 推进技术, 1997, 18(3): 79-81. (WU Ding-yi. An Experimental Investigation on Seal Character of Straight-Through Labyrinth[J]. Journal of Propulsion Technology, 1997, 18(3): 79-81.)
[8] 吴丁毅. 交错式篦齿封严特性的实验研究[J]. 推进技术, 1997, 18(2): 87-90. (WU Ding-yi. An Experimental Investigation on Sealing Characteristic of Interlacing Labyrinth[J]. Journal of Propulsion Technology, 1997, 18(2): 87-90.)
[9] 王代军, 苏云亮, 罗翔. 旋转状态下篦齿流量特性试验研究[J]. 燃气涡轮试验与研究, 2007, 20(2): 41-44.
[10] 王锁芳, 吕海峰. 转静态封严篦齿流场的数值分析和封严特性的研究[J]. 航空动力学报, 2005, 20(3):444-449.
[11] 呼艳丽, 刘玉芳, 王鹏飞. 旋转状态下阶梯齿风阻温升的初步分析[J]. 燃气涡轮试验与研究, 2009, 22(3): 47-49.
[12] Willenborg K, Kim S, Wittig S. Effects of Reynolds Number and Pressure Ratio on Leakage Loss and Heat Transfer in a Stepped Labyrinth Seal[J]. Journal of Turbomachinery, 2001, 123: 815-822.
[13] Wellborn S R. Details of Axial Compressor Shrouded Stator Cavity Flows[R]. ASME 2001-GT-0495.
[14] 刘高文, 孔晓治, 陈凯, 等. 转动和旋流对压气机级间封严影响的数值研究[J]. 推进技术, 2014, 35(12): 1687-1693. (LIU Gao-wen, KONG Xiao-zhi, CHEN Kai, et al. Numerical Study for Effects of Rotation and Swirl on Labyrinth Sealing in a Compressor Stator Well[J]. Journal of Propulsion Technology, 2014, 35(12): 1687-1693.)
[15] 刘高文, 陈凯, 钢铁. 等. 压比和雷诺数对压气机级间篦齿封严流动特性的影响[J]. 航空动力学报, 2015, 30(7): 1554-1560.
[16] Xiaozhi KONG, Gaowen LIU, Yuxin LIU, et al. Investigation on the Leakage Flow, Windage Heating and Swirl Development of Rotating Labyrinth Seal in a Compressor Stator Well[R]. ASME 2016-GT-56740.
[17] Sangan C M, Scobie J A, Owen J M, et al. Performance of a Finned Turbine Rim Seal[R]. ASME 2014-GT-25626.
[18] Peter R N Childs. Rotating Flow[M]. UK: Butterworth-Heinemann, 2011.　　　　　　　　　　　　　*　收稿日期:2016-05-05；修订日期:2016-06-23。作者简介:雷昭,男,硕士生,研究领域为发动机空气系统和旋转盘腔中的流动传热。E-mail: leizhao_nwpu@163.com(编辑:史亚红)