涡轮盘轮缘封严结构参数对封严效率影响的实验研究

推进技术 ›› 2017, Vol. 38 ›› Issue (11): 2606-2612.

涡轮盘轮缘封严结构参数对封严效率影响的实验研究

邬泽宇¹,罗翔¹,刘冬冬¹,田淑青²,张颖²

北京航空航天大学能源与动力工程学院，北京 100191,北京航空航天大学能源与动力工程学院，北京 100191,北京航空航天大学能源与动力工程学院，北京 100191,中航商用航空发动机有限责任公司，上海 201108,中航商用航空发动机有限责任公司，上海 201108

发布日期:2021-08-15
作者简介:邬泽宇，男，硕士生，研究领域为燃气入侵。

Influence of Different Structural Parameters on Sealing Efficiency of Turbine Disc Rim

School of Energy and Power Engineering，Beijing University of Aeronautics and Astronautics，Beijing 100191，China,School of Energy and Power Engineering，Beijing University of Aeronautics and Astronautics，Beijing 100191，China,School of Energy and Power Engineering，Beijing University of Aeronautics and Astronautics，Beijing 100191，China,AECC Commercial Aircraft Engine CO.LTD，Shanghai 201108，China and AECC Commercial Aircraft Engine CO.LTD，Shanghai 201108，China

Published:2021-08-15

摘要/Abstract

摘要： 在航空发动机涡轮部件中，封严环的设计对涡轮盘腔的冷却封严有着至关重要的作用。使用CO₂浓度测量法针对静盘双齿动盘单齿封严环的结构参数(齿高和齿间距)变化对封严效率的影响进行了实验研究，目的在于获得封严结构的封严效率和最小封严流量的变化规律。实验在主流雷诺数[Rew]=4.39×105，旋转雷诺数7.51×105<[Re?]<1.30×106的范围内，测量了不同封严流量下的封严效率，以及不同结构参数下各工况的最小封严流量。结果表明:封严效率随封严流量和旋转雷诺数的增加而增加；最小封严流量随着齿间距的增大和齿高的减小而增大，[Gc]平均每增加7.5×10-4，所需的最小封严流量会增加8.0%，[Gov]平均每增加1.12×10-3，可使最小封严流量减少4.7%，同时旋转雷诺数的变化对变齿间距下的最小封严流量有明显效果，而在变齿高情况下则没有影响。

关键词: 转静系；封严环；结构参数；封严效率

Abstract: In aero-engine turbine components， the design of the sealing ring is very important for the cooling and sealing of the turbine disc. Effects of different structural parameters (seal clearance and axial overlap of radial-clearance seal) of the rim seal which has two seal teeth on the stator and one on the rotor on sealing efficiency were experimentally studied by measuring CO₂ concentration， in order to obtain the change rule of the sealing efficiency and the minimum flow rate of sealing air of the different sealing structure. Experiment was conducted under the condition that annulus Reynolds number ([Rew]) was set at 4.39×105 while the rotating Reynolds number ([Re?]) changed from 7.51×105 to 1.30×106 in order to investigate the sealing efficiency under different values of the sealing air and the minimum flow rate of sealing air with different structural parameters. The results indicate that， the sealing efficiency increases with the increase of the sealing air and the rotating Reynolds number， the minimum flow rate of sealing air increases as the seal clearance increases and the axial overlap of radial-clearance seal decreases. If the[Gc]increases 7.5×10-4， the minimum flow rate of sealing air that is necessary will increase by an average of 8%. While if the[Gov]increases 1.12×10-3， the minimum flow rate of sealing air will decrease by 4.7%. At the same time， the change of rotational Reynolds number has obvious effect on the minimum seal flow， when the seal clearance is changed. However it is different when the axial overlap of radial-clearance seal is changed.

Key words: Rotator-stator system；Rim seal；Structural parameters；Sealing efficiency

邬泽宇,罗翔,刘冬冬,田淑青,张颖. 涡轮盘轮缘封严结构参数对封严效率影响的实验研究[J]. 推进技术, 2017, 38(11): 2606-2612.

WU Ze-yu¹,LUO Xiang¹,LIU Dong-dong¹,TIAN Shu-qing²,ZHANG Ying². Influence of Different Structural Parameters on Sealing Efficiency of Turbine Disc Rim[J]. Journal of Propulsion Technology, 2017, 38(11): 2606-2612.

参考文献

[1] 曹玉璋. 航空发动机传热学[M]. 北京:北京航空航天大学出版社, 2005: 226-265.
[2] Owen J M. Prediction of Ingestion Through Turbine Rim Seals, Part I: Rotationally Induced Ingress[J]. Journal of Turbomachinery, 2011, 133(3).
[3] Owen J M. Prediction of Ingestion Through Turbine Rim Seals, Part II: Externally Inducedand Combined Ingress[J]. Journal of Turbomachinery, 2011, 133(3).
[4] Owen J M, Zhou K, Pountney O, et al. Theoretical Prediction of Ingress Through Turbine Rim Seals, Part I: Externally Induced Ingress[J]. Journal of Turbomachinery, 2012, 134(3).
[5] Owen J M, Pountney O, Lock G D. Prediction of Ingress Through Turbine Rim Seals, Part II: Combined Ingress[J]. Journal of Turbomachinery, 2012, 134(3).
[6] Teramachi K, Manabe T, Yanagidan N, et al. Effect of Geometry and Fin Overlap on Sealing Performance of Rim Seals[C]. Indianapolis: //38th AIAA/ASME/ SAE/ ASEE Joint Propulsion Conference & Exhibit, 2002.
[7] Roy R P, Feng J, Narzary D, et al. Experiments on Gas Ingestion Through Axial-Flow Turbine Rim Seals[R]. ASME 2004- GT- 53394.
[8] Roy R P, Zhou D W, Ganesan S, et al. The Flow Field and Main Gas Ingestion in a Rotor-Stator Cavity[R]. ASME 2007-GT-27671.
[9] Roy R P, Zhou D W, Kim Y W, et al. Experiments on Aft-Disk Cavity Ingestion a 1.5- Stage Axial-Flow Turbine[R]. ASME 2011 -GT- 45895.
[10] Sangan C M. Measurement of Ingress Through Gasturebine Rim Seals[D]. UK: University of Bath, 2011.
[11] Hills N J, Chew J W, Turner AB. Computational and Mathematical Modelling of Turbine Rim Seal Ingestion[J]. Journal of Turbomachinery, 2002, 124(2): 306-315.
[12] Gentilhomme O, Hills N J, Turner A B, et al. Me- asurements and Analysis of Ingestion Through a Turbine Rim Seal[J]. Journal of Turbomachinery, 2003, 125(3): 505-512.
[13] O’Mahoney T S D, Hills N J, Chen J W, et al. Large-Eddy Simulation of Rim Seal Ingestion[R]. ASME 2010-GT-229362.
[14] 马宏伟, Dieter E Bohn, Achim Decker, et al. 涡轮级轮缘封严内非定常流场的准三维LDV测量[J]. 航空动力学报, 2004, 19(4): 455-459.
[15] Xing Luo, Dongdong Liu, Hongwei Wu, et al. PIV Measurement and CFD Simulations of the Unsteady Flow within a Rotating Disk Cavity[J]. Journal of Engineering for GasTurbines and Power, 2014, 136(11).
[16] 朱莉娅, 罗翔, 徐国强, 等. 涡轮级燃气入侵的理论分析及数值模拟[J]. 推进技术, 2014, 35(11): 1511-1516. (ZHU Li-ya, LUO Xiang, XU Guo-qiang, et al. A Theoretical and Numerical Study of Turbine Rim Seal Ingestion[J]. Journal of Propulsion Technology, 2014, 35(11): 1511-1516.)
[17] Wang C Z, Johnson B V , Jong F D, et al. Comparison of Flow Characteristics in Axial-Gap Seals for Close-and Wide-Spaced Turine Stages[C]. Montreal: ASME Turbo Expo 2007: Power for Land, Sea and Air, 2007.
[18] 罗翔, 张达, 徐国强. 中心进气开式转静系转盘风阻扭矩实验[J]. 推进技术, 2015, 36(8): 1199-1205. (LUO Xiang, ZHANG Da, XU Guo-qiang. Experimental Study on Windage Torque in Unshrouded Rotor-Stator System with Central Inflow[J]. Journal of Propulsion Technology, 2015, 36(8): 1199-1205.)
[19] 张晶辉, 马宏伟. 轮缘封严气体对涡轮转子性能影响的非定常数值研究[J]. 推进技术, 2014, 35(4): 470-478. (ZHANG Jing-hui, MA Hong-wei. Unsteady Numerical Investigation for Effects of Rim Sealing Flow on Performance of a Turbine Rotor[J]. Journal of Propulsion Technology, 2014, 35(4): 470-478.)
[20] 林立, 谭勤学, 吴康. 低位预旋进气转静系盘腔流动特性研究[J]. 推进技术, 2016, 37(2): 258-265. (LIN Li, TAN Qin-xue, WU Kang. Study of Flow Dynamics in Rotor-Stator Cavity with Low-Radius Preswirl Inlet[J]. Journal of Propulsion Technology, 2016, 37(2): 258-265.)　　　　　　　　　　　　　*　收稿日期:2016-06-07；修订日期:2016-09-18。作者简介:邬泽宇,男,硕士生,研究领域为燃气入侵。E-mail: sxwzy1015@163.com(编辑:梅瑛)