微弧等离子堆焊沉积Ni/硅藻土高温封严涂层的腐蚀磨损特性

推进技术 ›› 2017, Vol. 38 ›› Issue (2): 457-462.

微弧等离子堆焊沉积Ni/硅藻土高温封严涂层的腐蚀磨损特性

袁晓静¹,查柏林²,陈小虎¹,阳能军¹,姚春江¹

火箭军工程大学装备管理工程系，陕西西安 710025,火箭军工程大学动力工程系，陕西西安 710025,火箭军工程大学装备管理工程系，陕西西安 710025,火箭军工程大学装备管理工程系，陕西西安 710025,火箭军工程大学装备管理工程系，陕西西安 710025

发布日期:2021-08-15
作者简介:袁晓静，男，博士，副教授，研究领域为装备技术保障。
基金资助:
国家自然科学基金青年基金(51405497)。

Corrosive-Wearing Resistance Behavior of Ni/Diatomite Abradable Seal Coatings Produced by Micro-Arc Plasma Welding

Department of Equipment Management Engineering，Rocket Engineering University，Xi’an 710025，China,Department of Power Engineering，Rocket Engineering University，Xi’an 710025，China,Department of Equipment Management Engineering，Rocket Engineering University，Xi’an 710025，China,Department of Equipment Management Engineering，Rocket Engineering University，Xi’an 710025，China and Department of Equipment Management Engineering，Rocket Engineering University，Xi’an 710025，China

Published:2021-08-15

摘要/Abstract

摘要： 高温封严涂层在腐蚀环境中的摩擦磨损是影响其服役寿命的主要问题之一。为此，研究了微弧等离子堆焊沉积Ni/硅藻土封严涂层的工艺规律与腐蚀摩擦学性能。对粉末和涂层的基本结构的表征显示:涂层呈现堆叠结构，含有大量孔隙，涂层主要由Ni，SiO₂和少量NiO组成。涂层的内聚强度平均达到8.78MPa，在拉伸应力作用下表现为以扁平化粒子边缘为主，沿着孔隙率方向应力集中的脆性断裂，以及在应力集中部位导致硅藻土粒子内部的穿晶断裂。当堆焊电流为40A时，微弧等离子堆焊制备的Ni/硅藻土封严涂层在盐环境和酸环境的摩擦系数和磨损率分别达到0.524，16.354wt.‰和0.5099，17.317wt.‰。Ni/硅藻土可磨耗封严涂层在酸性环境的腐蚀能力较低，其平衡电位达到-708mV。

关键词: Ni/硅藻土；微弧等离子堆焊；腐蚀磨损；微观结构

Abstract: The wear property at corrosion environment is one of the main problems in the service life cycle of high temperature sealing coating. The micro-structure and corrosive-wearing resistance properties of Ni/diatomite coatings deposited by micro-arc plasma welding was reported. It shows that the coatings with a layer structure contain a large number of pores，which are mainly composed of Ni，SiO₂ and a small amount of NiO. The mean bonding strength of coatings is about 8.78MPa. Under the tensile stress，the fracture mechanism takes on the cohesive strength，where the stress were focused on the edge of flattened particle，the direction of the porosity of the brittle fracture，and diatomite particles within the trans-granular fracture. In the salt and acidic environment，when the welding current is 40A，the friction coefficient and wear rate of Ni/ diatomite abradable coatings produced by micro-arc plasma welding were stable relatively，and reached 0.524，16.354wt.‰ and 0.5099，17.317wt.‰，respectively. At acidic solution environment，the corrosion resistance performance of Ni/ diatomite abradable coatings is lower than that in the salt solution，and the equilibrium potential is -708mV.

Key words: Ni/diatomite；Micro plasma welding；Corrosion-wear；Micro-structure

袁晓静,查柏林,陈小虎,阳能军,姚春江. 微弧等离子堆焊沉积Ni/硅藻土高温封严涂层的腐蚀磨损特性[J]. 推进技术, 2017, 38(2): 457-462.

YUAN Xiao-jing¹,ZHA Bai-lin²,CHEN Xiao-hu¹,YANG Neng-jun¹,YAO Chun-jiang¹. Corrosive-Wearing Resistance Behavior of Ni/Diatomite Abradable Seal Coatings Produced by Micro-Arc Plasma Welding[J]. Journal of Propulsion Technology, 2017, 38(2): 457-462.

参考文献

[1] 张俊红, 鲁鑫, 何振鹏, 等. 航空发动机可磨耗封严涂层技术研究及性能评价[J]. 材料工程, 2016, 4: 94-109.
[2] Liu Wei, Zhou Kui, Du Lingzhong, et al. Frictional Wear Resistance and Erosion Resistance of Abradable Seal Coating[J]. Journal of Thermal Spray Technology, 2012, 4(4): 34-41.
[3] Stringern J, Marshell M B. High Speed Wear Testing of Abradable Coatings[J]. Wear, 2012, (294-295): 257-263.
[4] 曹茜, 李其连, 叶卫平, 等. 等离子喷涂 NiCrAlYSi 基封严涂层的性能研究[J]. 热喷涂技术, 2014, 3: 35-39.
[5] 徐娜, 张春智, 栾胜家, 等. NiCrAl/Diatomite可磨耗封严涂层摩擦磨损性能研究[C]. 洛阳:第十六届国际热喷涂研讨会(ITSS’2013)暨第十七届全国热喷涂年会(CNTSC’2013)论文集, 2013: 16-20.
[6] 刘慧, 马寒岩, 赵延春, 等. 镍铬铝-硅藻土可磨耗封严涂层的热稳定性[J]. 焊接技术, 2011, (3): 13-15.
[7] Sveja E, Robert M, Daniel M, et al. Failure Mechanisms of Magnesia Alumina Spinel Abradable Coatings under Thermal Cyclic Loading[J]. Journal of the European Ceramics Society, 2013, 33: 3335-3343.
[8] 薛伟海, 高禩洋, 段德莉, 等. 高速刮擦下Ni-G封严涂层与Ti6Al4V叶片间的材料转移行为[J]. 中国表面工程, 2014, 10: 65-72.
[9] 邢丕臣, 刘建明, 王志伟, 等. 可磨耗封严涂层抗中性盐雾腐蚀性能研究[J]. 热喷涂技术, 2015, 12: 35-41.
[10] 于方丽, 白宇, 吴秀英, 等. 等离子喷涂镍基可磨耗封严涂层抗腐蚀及耐磨性能分析[J]. 无机材料学报, 2016, 31(7): 687-693.
[11] 许存官, 杜令忠, 张伟刚. Ni/石墨封严涂层的盐雾腐蚀研究[J]. 航空材料学报, 2010, 30(4): 53-58.
[12] 杨晓军, 许诺然, 刘智刚. 污染物沉积和热障涂层脱落对气膜冷却效率影响的数值研究[J]. 推进技术, 2013, 34(10): 1362-1368. (YANG Xiao-jun, XU Nuo-ran, LIU Zhi-gang, Effects of Deposition and Thermal Barrier Coating Spallation on Film Cooling Effectiveness: a Numerical Study[J]. Journal of Propulsion Technology, 2013, 34(10): 1362-1368.)
[13] 朱向哲, 袁惠群, 李东. 摩擦热效应对航空发动机高压转子系统碰摩响应的影响[J]. 推进技术, 2010, 31(3): 366-271. (ZHU Xiang-zhe, YUAN Hui-qun, LI Dong. Friction Thermal Effect on Rubbing Response of a High Pressure Rotor System[J]. Journal of Propulsion Technology, 2010, 31(3): 366-271.)
[14] 邓德伟, 陈蕊, 张洪潮. 等离子堆焊技术的现状及发展趋势[J]. 机械工程学报, 2013, 49(7): 106-111.
[15] Yang L J. Plasma Surface Hardening of ASSAB 760 Steel Specimens with Taguchi Optimization of the Processing Parameters[J]. Journal of Materials Processing Technology, 2001, (113): 521-526.
[16] 张峰, 黄传兵, 兰昊, 等. TiAl/BN 复合封严涂层的耐腐蚀性能研究[J]. 热喷涂技术, 2014, 12: 23-27.　收稿日期:2016-09-26；修订日期:2016-10-13。基金项目:国家自然科学基金青年基金(51405497)。作者简介:袁晓静,男,博士,副教授,研究领域为装备技术保障。E-mail: yxj2003@263.net(编辑:张荣莉)