不同进口边界层条件下S形扩压器流场特性研究

推进技术 ›› 2017, Vol. 38 ›› Issue (4): 751-758.

不同进口边界层条件下S形扩压器流场特性研究

何鹏,董金钟

北京航空航天大学能源与动力工程学院，北京 100191,北京航空航天大学能源与动力工程学院，北京 100191

发布日期:2021-08-15
作者简介:何鹏，男，博士生，研究领域为发动机内流空气动力学。

Investigation of Flow Characteristics in a Diffusing S-Duct at Different Inlet Boundary Layer Conditions

School of Energy and Power Engineering，Beijing University of Aeronautics and Astronautics，Beijing 100191，China and School of Energy and Power Engineering，Beijing University of Aeronautics and Astronautics，Beijing 100191，China

Published:2021-08-15

摘要/Abstract

摘要： 为了研究S形扩压器边界层分离和二次流之间相互作用的机制，采用数值模拟方法，对不同进口边界层条件下的S形扩压器内流场进行了计算。结果表明:边界层分离和二次流之间存在着密切关系，边界层分离带来的大面积低速区显著地加大了二次流的强度和尺度，二次流又反过来会改变分离区的分布。S形扩压器二次流的发展可认为是两个弯道产生的流向涡相互对抗的过程，对于进口带有长等直段的方案，边界层更易发生分离，扩压器出口二次流最终发展成为“上抬涡”模式。此时总压恢复系数等于0.978，而总压畸变指数和旋流系数分别高达0.55和0.035，其气动性能明显劣于无长等直段的方案。

关键词: S形扩压器；进口边界层；边界层分离；二次流；总压恢复；总压畸变

Abstract: In order to investigate the interaction mechanism between boundary layer separation and secondary flows in a diffusing S-duct，numerical simulations were performed for the internal flow field of the diffusing S-duct at different inlet conditions. The results show that boundary layer separation and secondary flows are closely related to each other: the large area of low-energy fluid caused by boundary layer separation significantly increases the strength and size of secondary flows，in turn，secondary flows can change the distribution of the separation region. The development of secondary flows is dependent on the competition between streamwise vortices，which are induced from the two opposite bends of the S-duct. For the case with long straight section，boundary layer is more prone to separation，and a‘lifted vortex’pattern is observed at the S-duct outlet. The total pressure recovery is 0.978，the total pressure distortion coefficient and swirl coefficient are 0.55 and 0.035，respectively，suggesting that the aerodynamic performance is considerably worse than the case without long straight section.

Key words: Diffusing S-duct；Inlet boundary layer；Boundary layer separation；Secondary flow；Total pressure recovery；Total pressure distortion

何鹏,董金钟. 不同进口边界层条件下S形扩压器流场特性研究[J]. 推进技术, 2017, 38(4): 751-758.

HE Peng,DONG Jin-zhong. Investigation of Flow Characteristics in a Diffusing S-Duct at Different Inlet Boundary Layer Conditions[J]. Journal of Propulsion Technology, 2017, 38(4): 751-758.

参考文献

[1] 张考, 马东立. 军用飞机生存力与隐身设计[M]. 北京:国防工业出版社, 2002.
[2] Wellborn S R, Reichert R A, OKiishi T H, et al. Study of the Compressible Flow in a Diffusing S-Duct[J]. Journal of Propulsion and Power, 1994, 10(5): 668-675.
[3] Anabtawi A J, Blackwelder R F, Liebeck R H, et al. Experimental Investigation of Boundary Layer Ingesting Diffusers of a Semi-Circular Cross Section [R]. AIAA 98-0945.
[4] Seddon J, Goldsmith E L. Intake Aerodynamics [M]. London: Blackwell Science, 1999.
[5] MacMartin D G, Murray R M, Verma A, et al. Active Control of Integrated Inlet Compressor Systems: Initial Results [R]. FEDSM 2001-18275.
[6] Shimizu Y, Nagafusa M, Sugino K, et al. Studies on Performance and Internal Flow of Twisted S-Shaped Bend Diffuser - the So-Called Coiled Bend Diffuser: 1st Report [J]. Journal of Fluids Engineering, 1986, 108(3): 289-296.
[7] Abdellatif O E, Abdrabbo M, Abdelganny M, et al. Area Ratio Effect on the Turbulent Flow Through a Diffusing S-Duct Using Large-Eddy Simulation[R]. AIAA 2008-5726.
[8] 郭荣伟. 矩形截面S弯扩压器旋流的研究[J]. 南京航空航天大学学报, 1985, 17(2): 70-79.
[9] Ng Y T, Luo S C, Lim T T, et al. On Swirl Development in a Square Cross-Sectioned S-Shaped Duct[J]. Experiments in Fluids, 2006, 41(6): 975-989.
[10] Mayer D W, Anderson B H, Johnson T A. 3D Subsonic Diffuser Design and Analysis[R]. AIAA 98-3418.
[11] Potsdam M A, Page M A, Liebeck R H. Blended Wing Body Analysis and Design[R]. AIAA 97-2317.
[12] Liebeck R H. Design of the Blended Wing Body Subsonic Transport[J]. Journal of Aircraft, 2004, 41(1): 10-25.
[13] Dehpanah P, Nejat A. The Aerodynamic Design Evaluation of a Blended-Wing-Body Configuration[J]. Aerospace Science and Technology, 2014, 43: 96-110.
[14] Owens L R, Allan B G, Gorton S A. Boundary-Layer-Ingesting Inlet Flow Control[J]. Journal of Aircraft, 2008, 45(4): 1431-1440.
[15] Laskaridis P, Pachidis V, Pilidis P. Opportunities and Challenges for Distributed Propulsion and Boundary Layer Ingestion[J]. Aircraft Engineering and Aerospace Technology, 2014, 86(5): 451-458.
[16] 王健, 李应红, 张百灵. 亚声速进气道出口流场畸变控制研究 [J]. 推进技术, 2010, 31(2): 143-146. (WANG Jian, LI Ying-hong, ZHANG Bai-ling. Investigation on Flow Distortion Control of a Subsonic Inlet [J]. Journal of Propulsion Technology, 2010, 31(2): 143-146.)
[17] 刘雷, 宋彦萍, 陈焕龙, 等. 半埋入式S弯进气道设计及其优化 [J]. 推进技术, 2014, 35(10): 1303-1309. (LIU Lei, SONG Yan-ping, CHEN Huang-long, et al. Design and Optimization of Half Flush-Mounted S-Shaped Inlet[J]. Journal of Propulsion Technology, 2014, 35(10): 1303-1309.)
[18] Lee C C, Boekicker C. Subsonic Diffuser Design and Performance for Advanced Fighter Aircraft[R]. AIAA 85-3073.
[19] Abhinav K. Flow Control Optimization in a Jet Engine Serpentine Inlet Duct [D]. Texas: Texas A&M University, 2007.
[20] Fiola C, Agarwal R K. Simulation of Secondary and Separated Flow in a Diffusing S-Duct Using Four Different Turbulence Models[J]. Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering, 2014, 228(11): 1954-1963.
[21] Anabtawi A J, Blackwelder R F, Lissaman P, et al. An Experimental Investigation of Boundary Layer Ingestion in a Diffusing S-Duct with and without Passive Flow Control [R]. AIAA 99-0739.　　　　　　　　　　　　*　收稿日期:2015-11-27；修订日期:2016-01-29。作者简介:何鹏,男,博士生,研究领域为发动机内流空气动力学。E-mail: hepeng_buaa@163.com(编辑:梅瑛)