壁面压力可控的基准流场设计参数影响研究与优化设计

推进技术 ›› 2017, Vol. 38 ›› Issue (8): 1732-1740.

壁面压力可控的基准流场设计参数影响研究与优化设计

徐锦¹,罗金玲²,戴梧叶²

北京机电工程研究所，北京100074,北京空天技术研究所，北京 100074,北京空天技术研究所，北京 100074

发布日期:2021-08-15
作者简介:徐锦，男，硕士，研究领域为飞行器设计，空气动力学。

Effects of Design Parameters Analysis and Optimization Design of Basic Flowfield with Controlled Pressure Distribution

Beijing Electro-Mechanical Engineering Institute，Beijing 100074，China,Beijing Aerospace Technology Institute，Beijing 100074，China and Beijing Aerospace Technology Institute，Beijing 100074，China

Published:2021-08-15

摘要/Abstract

摘要： 根据有旋特征线理论，设计了沿程壁面压力分布可控的轴对称基准流场，分析了Ma=6.5状态基准流场的设计参数(包括壁面前缘压缩角、中心体半径和壁面压升规律等)的影响规律。结果表明:前缘压缩角的增大会使基准流场的增压比增加、总压恢复降低；较小的中心体半径有利于减小内收缩比，提高流场起动性能；壁面压力梯度递增的基准流场的压缩效率高。最后，针对基准流场，建立了多项式响应面模型并利用多目标遗传算法进行优化，根据优化获得的Pareto最优前沿选取两个流场进行比较。和选定的流场长度、出口总压恢复系数基本不变的其中一流场相比较，另一流场的收缩比增加了9.5%，增压比提高了14%，喉道马赫数降低了约3.2%，说明优化结果可为选取性能优良的基准流场提供参考。

关键词: 高超声速；基准流场；壁面压力规律；响应面模型；优化设计

Abstract: Axisymmetric basic flowfield with controlled wall pressure gradient is designed using the rotational method of characteristics. The effects of basic flowfield design parameters such as leading edge deflection angle，center body radius and wall pressure law are studied at Ma=6.5. The results show that the pressure compression ratio would increase and total pressure recovery would decrease with the leading edge deflection angle increase. Small center body radius could reduce the internal compression ratio and improve the starting performance of basic flowfield. Moreover，the basic flowfield with wall pressure gradient increasing has the high compression efficiency. At last，the overall performances of the optimized basic flowfield is studied by the multi-objective GA( genetic algorithm) based on the polynomial response surface at design point and the performances of two different basic flowfields which are choosed due to Pareto optimal front are compared. The results indicate that compared with one basic flowfield that the length and the total pressure recovery of outlet almost remain unchanged，the contraction ratio of the other basic flowfield raises 9.5%，the pressure compression ratio raises 14%，the Mach number of throat decreases 3.2%，which verifies that good performance flowfield could be designed on the basis of the optimization results.

Key words: Hypersonic；Basic flowfield；Wall pressure rise law；Response surface model；Optimization design

徐锦,罗金玲,戴梧叶. 壁面压力可控的基准流场设计参数影响研究与优化设计[J]. 推进技术, 2017, 38(8): 1732-1740.

XU Jin¹,LUO Jin-ling²,DAI Wu-ye². Effects of Design Parameters Analysis and Optimization Design of Basic Flowfield with Controlled Pressure Distribution[J]. Journal of Propulsion Technology, 2017, 38(8): 1732-1740.

参考文献

[1] Colville J R, Starkey R P, Lewis M J. Extending the Flight Mach Number of the SR-71 Inlet[R]. AIAA 2005-3284.
[2] 范晓樯, 李桦, 李晓宇, 等. 高超声速二维进气道参数化设计方法初探[J]. 航空动力学报, 2007, 22(1): 66-72.
[3] 金志光, 张堃元. 高超侧压式进气道高焓脉冲风洞实验[J]. 推进技术, 2005, 26(4): 319-323. (JIN Zhi-guang, ZHANG Kun-yuan. Test of a Generic Sidewall Compression Scramjet Inlet in the High-Enthalpy Impulse Wind Tunnel[J]. Journal of Propulsion Technology, 2005, 26(4): 319-323.)
[4] 尤延铖, 梁德旺, 黄国平. 一种新型内乘波式进气道初步研究[J]. 推进技术, 2006, 27(3): 252-256. (YOU Yan-cheng, LIANG De-wang, HUANG Guo-ping. Investigation of Internal Waverider-Derived Hypersonic Inlet[J]. Journal of Propulsion Technology, 2006, 27(3): 252-256.)
[5] Molder S, Szpiro J. Busemman Inlet for Hypersonic Speed [J]. Journal of Spacecraft and Rockets, 1966, 3(8): 1301-1304.
[6] Smart M K. Design of Three-Demensional Hypersonic Inlets with Rectangular-to-Elliptical Shape Transition[J]. Journal of Propulsion and Power, 1999, 15(3): 408-416.
[7] Molder S. Internal Axismmetric Conical Flow[J]. AIAA Journal, 1967, 5(7): 1252-1255.
[8] Travis W D, Ioannis Nompelis, Graham V C. Hypersonic Inward Turning Inlets: Design and Optimization[R]. AIAA 2006-297.
[9] 南向军, 张堃元, 金志光, 等. 压升规律可控的高超声速内收缩进气道设计[J]. 航空动力学报, 2011, 26(3): 518-523.
[10] 朱伟, 张堃元, 南向军. 壁面马赫数分布规律可控的新型内收缩基准流场设计方法[J]. 推进技术, 2013, 34(4): 433-438. (ZHU Wei, ZHANG Kun-yuan, NAN Xiang-jun. Investigation on Basic Flowfield with Controlled Mach Gradient for Hypersonic Inward Turning Inlet[J]. Journal of Propulsion Technology, 2013, 34(4): 433-438.)
[11] 李永洲, 张堃元, 钟启涛. 型面设计马赫数对马赫数分布可控高超声速内收缩进气道的影响[J]. 南京航空航天大学学报, 2014, 46(2): 239-245.
[12] Homung H G. Oblique Shock Reflection from an Axis of Symmetry[J]. Fluid Machinery, 2001, 4009(1): 1-12.
[13] 马树微, 杜斌, 陈万春. 基于代理模型的高超声速飞行器协同优化设计[J]. 北京航空航天大学学报, 2013, 39(8): 1042-1047.
[14] Queipo N V, Haftka R T, Shy W, et al. Surrogate-Based Analysis and Optimization[J]. Progress in Aerospace Sciences, 2005, 41(1): 1-28.
[15] Forrester A I J, Keane A J. Recent Advances in Surrogate-Based Optimization[J]. Progress Sciences, 2009, 45(3): 50-79.
[16] 穆雪峰, 姚卫星, 余雄庆, 等. 多学科优化设计中常用代理模型的研究[J]. 计算力学学报, 2005, 22(5): 608-612.
[17] 李永洲, 张堃元, 王磊, 等. 马赫数分布可控的基准流场灵敏度分析与优化[J]. 航空动力学报, 2013, 28(4): 765-777.(编辑:张荣莉)　　　　　　　　　　　　　　收稿日期:2016-04-20；修订日期:2016-07-04。作者简介:徐锦,男,硕士,研究领域为飞行器设计,空气动力学。E-mail: xulianjin2008@163.com