涡轮叶顶间隙自适应控制的研究

推进技术 ›› 2017, Vol. 38 ›› Issue (9): 1921-1929.

• 学术前沿 • 下一篇

涡轮叶顶间隙自适应控制的研究

魏明,高杰,付维亮,王付凯,郑群

哈尔滨工程大学动力与能源工程学院，黑龙江哈尔滨 150001,哈尔滨工程大学动力与能源工程学院，黑龙江哈尔滨 150001,哈尔滨工程大学动力与能源工程学院，黑龙江哈尔滨 150001,哈尔滨工程大学动力与能源工程学院，黑龙江哈尔滨 150001,哈尔滨工程大学动力与能源工程学院，黑龙江哈尔滨 150001

发布日期:2021-08-15
作者简介:魏明，男，硕士生，研究领域为叶轮机械气动热力学。 E-mail: 2448637022@hrbeu.edu.cn 通讯作者:高杰，男，博士，副教授，研究领域为叶轮机械气动热力学。
基金资助:
国家自然科学基金项目(51406039)；黑龙江省青年科学基金(QC2016059)。

Study of Adaptive Tip Clearance Control in Turbines

College of Power and Energy Engineering，Harbin Engineering University，Harbin 150001，China,College of Power and Energy Engineering，Harbin Engineering University，Harbin 150001，China,College of Power and Energy Engineering，Harbin Engineering University，Harbin 150001，China,College of Power and Energy Engineering，Harbin Engineering University，Harbin 150001，China and College of Power and Energy Engineering，Harbin Engineering University，Harbin 150001，China

Published:2021-08-15

摘要/Abstract

摘要： 为了达到减小涡轮叶片叶顶间隙泄露的目的，应用数值模拟并辅之试验的方法对叶顶间隙泄漏流动形成机理、涡轮自适应叶顶喷气控制机理及其对间隙流动的控制作用进行了研究。在此基础上，着重研究了进口位置、出口位置、喷气孔直径等自适应叶顶喷气孔参数以及叶顶间隙大小，对叶顶喷气效果的影响规律。结果表明:自适应叶顶喷气孔进口位置对叶顶喷气性能影响不大；出口位置在叶顶中部，靠近压力面时，叶顶喷气效果最佳；喷气孔直径为2mm (d/H=4.8%相对叶高)时效果较好；叶顶间隙越大，叶顶喷气效果越差，当间隙取到2mm (t/H=4.8%相对叶高)时，叶顶喷气已经失去控制间隙泄漏的作用了。

关键词: 自适应；叶顶喷气孔；间隙泄漏；喷气孔参数

Abstract: In order to reduce the turbine blade tip clearance leakage，application of the method about numerical simulation and experiment to research the tip clearance leakage flow formation mechanism，turbine adaptive tip jet hole control mechanism and its control of flow gap was carried out. On this basis，focuses on the adaptive tip jet hole parameters about the import position，the outlet position，jet hole diameter and the size of blade tip clearance，on the tip of the jet effect. The results showed that adaptive tip jet hole import position leaves little effect on the performance of the tip jet when the export position located in the middle of the tip and close to the pressure surface，the tip jet can get the best performance with the adaptive tip jet hole diameter being 2mm (d/H=4.8% relative blade height)，the adaptive tip jet hole can get better performance. The larger the tip clearance，the worse the effect of jet tip. When the tip clearance gets to 2mm (t/H=4.8% relative blade height)，the adaptive tip jet hole have lost the effect of blocking flow.

Key words: Adaptive；Tip jet hole；Clearance leakage flow；Jet hole parameter

魏明,高杰,付维亮,王付凯,郑群. 涡轮叶顶间隙自适应控制的研究[J]. 推进技术, 2017, 38(9): 1921-1929.

WEI Ming,GAO Jie,FU Wei-liang,WANG Fu-kai,ZHENG Qun. Study of Adaptive Tip Clearance Control in Turbines[J]. Journal of Propulsion Technology, 2017, 38(9): 1921-1929.

参考文献

[1] Schaub U W, Vlasic E, Moustapha S H. Effect of Clearance on the Performance of a Highly Loaded Turbine Stage[R]. AGARD-CP-537, 1993.
[2] Schleer M, Song S J, Abhari R S. Clearance Effects on the Onset of Instability in a Centrifugal Compressor[J]. ASME Journal of Turbomachinery, 2008, 130(7).
[3] 高杰, 郑群, 张曦, 等. 涡轮叶顶泄露涡非定常破碎特效分析[J]. 推进技术, 2016, 37(2): 242-249. (GAO Jie, ZHENG Qun, ZHANG Xi, et al . Analysis of Unsteady Breakdown Characteristics of Tip Leakage Vortex in Turbines[J]. Journal of Propulsion Technology, 2016, 37(2): 242-249.)
[4] 李刚, 徐燕骥, 林彬, 等. 利用介质阻挡放电等离子体控制压气机叶栅端壁二次流[J]. 中国科学:技术科学, 2009, 39(11): 1843-1849.
[5] Rao N M, Camci C. Axial Turbine Tip Desensitization by Injection from a Tip Trench: Part I Effect of Injection Mass Flow Rate[R]. ASME GT-2004-53256.
[6] Harvey N W, Newman D A, Haselbach F, et al. An Investigation into a Novel Turbine Rotor Winglet: Part 2 Numerical Simulation and Experimental Results[R]. ASME GT-2006-90459.
[7] Lee S W, Kim K H. Aerodynamic Performance of Winglets Covering the Tip Gap Inlet in a Turbine Cascade[J].International Journal of Heat and Fluid Flow, 2012, 34: 36-46.
[8] 胡建军, 徐进良, 曹海亮, 等. 超微型涡轮中极低展弦比静叶栅流场特性的数值研究[J]. 热能动力工程, 2009, 29(7): 656-663.
[9] 胡建军, 徐进良, 曹海亮, 等. 超微涡轮动叶栅叶顶间隙对流场影响的数值模拟[J]. 热能动力工程, 2010, 25(2): 134-140.
[10] 李伟, 乔渭阳, 许开富, 等. 涡轮叶尖泄漏流被动控制数值模拟[J]. 推进技术, 2008, 29(5): 591-597. (LI Wei, QIAO Wei-yang, XU Kai-fu, et al . Numerical Simulation of Passive Control on Tip Leakage Flow in Axial Turbine[J]. Journal of Propulsion Technology, 2008, 29(5): 591-597.)
[11] 蔡晋, 陈波, 闫雪, 等. 带小翼肋条的涡轮叶尖泄漏流场的数值模拟[J] . 动力工程学报, 2010, 30(12): 919-925.
[12] 查小晖, 郑群, 高杰, 等. 弧形端壁造型对不带冠涡轮气动性能的影响[J]. 推进技术, 2014, 35(6): 779-787. (ZHA Xiao-hui, ZHENG Qun, GAO Jie, et al . Effects of Arcing Endwall Contouring on Aerodynamic Performances of Unshrouded Axial Turbine[J]. Journal of Propulsion Technology, 2014, 35(6): 779-787.)
[13] 刘茂升, 臧述升. 机匣喷气位置对涡轮间隙流动控制的影响[J]. 推进技术, 2009, 30(5): 594-598. (LIU Mao-sheng, ZANG Shu-sheng. Effects of Casing Air Injection Position on Controlling Tip Clearance Flow in Axial Turbines[J]. Journal of Propulsion Technology, 2009, 30(5): 594-598.)
[14] Auxier T A. Aerodynamic Tip Sealing for Rotor Blades[P]. United States Patent No: 5403158, 1995.
[15] 曹传军, 黄国平, 夏晨. 一种减小涡轮叶尖泄漏流的方法[J]. 航空动力学报, 2011, 26(1): 99-107.
[16] 曹传军. 叶尖间隙对微涡轮叶栅内流影响机理与叶尖逆向涡控研究[M]. 南京:南京航天航空大学, 2011.
[17] Hamik M, Willinger R. An Innovative Passive Tip-Leakage Control Method for Axial Turbine: Basic Concept and Performance Potential[J]. Journal of Thermal Science, 2007, 16(3): 215-222.
[18] Ameri A A, Steinthorsson E, Rigby D L. Effect of Squealer Tip on Rotor Heat Transfer and Efficiency[J]. Journal of Turbomachinery, 1998, 120(4): 753-759.
[19] 胡建军, 孔祥东, 徐进良. 间隙高度对自发射流抑制叶尖泄漏的影响[J] . 航空动力学报, 2013, 28(7):1510-1516.　　　　　　　　　　　　　*　收稿日期:2016-06-07；修订日期:2016-07-25。基金项目:国家自然科学基金项目(51406039)；黑龙江省青年科学基金(QC2016059)。作者简介:魏明,男,硕士生,研究领域为叶轮机械气动热力学。 E-mail: 2448637022@hrbeu.edu.cn通讯作者:高杰,男,博士,副教授,研究领域为叶轮机械气动热力学。E-mail: gaojie_d@hrbeu.edu.cn(编辑:张荣莉)

涡轮叶顶间隙自适应控制的研究

Study of Adaptive Tip Clearance Control in Turbines

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 0

编辑推荐

Metrics

本文评价