端壁合成射流对高负荷涡轮叶栅涡系结构和流动损失影响的数值研究

推进技术 ›› 2018, Vol. 39 ›› Issue (1): 33-45.

端壁合成射流对高负荷涡轮叶栅涡系结构和流动损失影响的数值研究

于洪石,王志恒,席光

西安交通大学能源与动力工程学院，陕西西安 710049,西安交通大学能源与动力工程学院，陕西西安 710049,西安交通大学能源与动力工程学院，陕西西安 710049

发布日期:2021-08-15
作者简介:于洪石，男，硕士生，研究领域为叶轮机械气动热力学。E-mail: yuhongshi@stu.xjtu.edu.cn 通讯作者:席光，男，博士，教授，研究领域为叶轮机械气动热力学。
基金资助:
国家自然科学基金资助项目(51576153；51236006)；辽宁重大装备协同创新中心资助。

Numerical Investigation on Effects of Endwall Synthetic Jet on Vortex and Flow Losses in a High-Loaded Turbine Cascade

School of Energy and Power Engineering，Xi’an Jiaotong University，Xi’an 710049，China,School of Energy and Power Engineering，Xi’an Jiaotong University，Xi’an 710049，China and School of Energy and Power Engineering，Xi’an Jiaotong University，Xi’an 710049，China

Published:2021-08-15

摘要/Abstract

摘要： 为探究端壁合成射流对高负荷涡轮叶栅中涡系结构和流动损失的影响，采用非定常数值模拟方法分析了不同激励参数下合成射流对Durham叶栅流动损失的控制效果以及涡系结构和流动损失的对应关系。结果表明，合成射流减小了前缘马蹄涡和通道涡的尺度，削弱了来自相邻叶片压力面的横向涡，略微增强了壁角涡，并间接削弱了壁面涡；在无量纲幅值和频率分别为0.073和1时，控制效果最佳，总压损失系数减小约为10.72%；从控制机理上讲，合成射流加强了主流和射流下游边界层的掺混，增加了边界层动量，从而削弱了马蹄涡；合成射流影响了叶片压力面的流动分离，改变了由于分离产生低能流体的位置和范围，从而削弱了横向涡。由于漩涡的削弱，流动损失也随之减小。

关键词: 合成射流；激励参数；主动流动控制；漩涡结构；流动损失

Abstract: To investigate the effect of endwall synthetic jet(SJ) on vortex structure and flow loss reduction in a high-loaded turbine cascade， unsteady numerical model of Durham cascade with SJ installed at the endwall upstream of the blade was established. A series of simulations were performed to determine beneficial excitation parameters. At the optimal excitation parameters， the influence of SJ on vortex structure and flow loss were investigated in detail and the association between them was focused on.The results indicated that the sizes of the horseshoe vortex and passage vortex were reduced; the transverse vortex originated from adjacent pressure surface were weakened; the corner vortex was slightly strengthened; the wall vortex was receded indirectly. Total pressure loss coefficient was decreased by 10.72% at the optimal excitation parameters when dimensionless excitation amplitude and frequency were 0.073 and 1， respectively. From the perspective of control mechanism， SJ enhanced the mixing of main fluid and boundary-layer fluid downstream of the jet， the momentum of boundary-layer fluid increased， so that the horseshoe vortex was weakened. SJ influenced the boundary separation at the pressure face of the blade， the region and position of low-energy fluid caused by boundary separation were changed， so that the transverse vortex was weakened. Flow loss was reduced as a result of weakened vortexes.

Key words: Synthetic jet；Excitation parameter；Active flow control；Vortex structure；Flow loss

于洪石,王志恒,席光. 端壁合成射流对高负荷涡轮叶栅涡系结构和流动损失影响的数值研究[J]. 推进技术, 2018, 39(1): 33-45.

YU Hong-shi,WANG Zhi-heng,XI Guang. Numerical Investigation on Effects of Endwall Synthetic Jet on Vortex and Flow Losses in a High-Loaded Turbine Cascade[J]. Journal of Propulsion Technology, 2018, 39(1): 33-45.

参考文献

[1] Knezevici D C, Sjolander S A, Praisner T J, et al. Measurements of Secondary Losses in a Turbine Cascade with the Implementation of Non-Axisymmetric Endwall Contouring[J]. Journal of Turbomachinery, 2008, 132(1): 1405-1417.
[2] McIntosh J, MacPherson R, Ingram G, et al. Profiled Endwall Design Using Genetic Algorithms with Different Objective Functions[R]. ASME 2011-GT-45836.
[3] 赵刚剑, 刘波, 那振喆, 等. 采用新型非轴对称端壁优化设计方法提高涡轮性能的数值研究[J]. 推进技术, 2014, 35(5): 597-602. (ZHAO Gang-Jian, LIU Bo, NA Zhen-zhe, et al. Improving the Performance of Turbine Based on a New Optimization Design Method[J]. Journal of Propulsion Technology, 2014, 35(5): 597-602.)
[4] Sauer H, Mu?Ller R, Vogeler K. Reduction of Secondary Flow Losses in Turbine Cascades by Leading Edge Modifications at the Endwall[J]. Journal of Turbomachinery, 2001, 123(2): 207-213.
[5] Becz S, Majewski M S, Langston L S. Leading Edge Modification Effects on Turbine Cascade Endwall Loss[R]. ASME 2003-GT-38898.
[6] Kumar K N, Govardhan M. Secondary Flow Loss Reduction in a Turbine Cascade with a Linearly Varied Height Streamwise Endwall Fence[J]. International Journal of Rotating Machinery, 2011, (1): 1-16.
[7] Philips D B, Cimbala J M, Treaster A L. Suppression of the Wing-Body Junction Vortex by Body Surface Suction[J]. Journal of Aircraft, 1992, 29(1): 118-122.
[8] 郭爽, 陆华伟, 宋彦萍, 等. 端壁附面层抽吸对大转角扩压叶栅旋涡影响的实验研究[J]. 推进技术, 2013, 34(11): 1466-1473. (GUO Shuang, LU Hua-wei, SONG Yan-ping, et al. Experimental Investigation on Effects of Endwall Boundary Layer Suction on Vortex of High-Turning Compressor Cascade[J]. Journal of Propulsion Technology, 2013, 34(11): 1466-1473.)
[9] 扈延林, 唐菲, 赵庆军, 等. 冲压叶栅边界层抽吸处理分析[J]. 推进技术, 2012, 33(3): 356-362. (HU Yan-lin, TANG Fei, ZHAO Qing-jun, et al. Numerical Investigation on the Effect of Boundary Layer Suction in a Ramrotor Cascade[J]. Journal of Propulsion Technology, 2012, 33(3): 356-362.)
[10] Johnson M J, Ravindra K, Andres R. Comparative Study of the Elimination of the Wing Fuselage Junction Vortex by Boundary Layer Suction and Blowing[R]. AIAA 94-0239.
[11] Glezer A, Amitay M. Synthetic Jets[J]. Annual Review of Fluid Mechanics, 2002, 34(1): 503-529.
[12] 张攀峰, 王晋军, 冯立好. 零质量射流技术及其应用研究进展[J]. 中国科学, 2008, 38(3): 321-349.
[13] Zander V, Hecklau M, Nitsche W, et al. Active Flow Control by Means of Synthetic Jets on a Highly Loaded Compressor Cascade[J]. Proceedings of the Institution of Mechanical Engineers, Part A: Journal of Power and Energy, 2011, 225(7): 897-908.
[14] Matejka M, Popelka L, Safarik P, et al. Influence of Active Methods of Flow Control on Compressor Blade Cascade Flow[R]. ASME 2008-GT-51109.
[15] Benini E, Biollo R, Ponza R. Efficiency Enhancement in Transonic Compressor Rotor Blades Using Synthetic Jets: A Numerical Investigation[J]. Applied Energy, 2011, 88(3): 953-962.
[16] Braunscheidel E P, Culley D E, Zaman K B M Q. Application of Synthetic Jets to Reduce Stator Flow Separation in a Low Speed Axial Compressor[J]. AIAA Journal, 2008, 602: 7-11.
[17] 王建明, 马驰, 李明, 等. 合成射流对角区马蹄涡的影响研究[J]. 航空科学技术, 2016, (1): 66-73.
[18] Wang S, Cai L, Zhou X, et al. Numerical Investigation on Effectiveness of Flow Separation Control in Two-Dimensional High-Load Compressor Cascade by Synthetic Jet[J]. Journal of Thermal Science, 2012, 21(5): 441-446.
[19] Zheng XQ, Zhou S, Lu YJ, et al. Flow Control of Annular Compressor Cascade by Synthetic Jets[J]. Journal of Turbomachinery, 2008, 130(2).
[20] 秦勇, 刘华坪, 王若玉, 等. 激励参数对合成射流控制压气机流动分离的影响[J]. 推进技术, 2017, 38(5): 1030-1037. (QIN Yong, LIU Hua-ping, WANG Ruo-yu, et al. Effects of Actuation Parameters on Flow Separation Control in Compressor with Synthetic Jets[J].Journal of Propulsion Technology, 2017, 38(5): 1030-1037.)
[21] Hilfer M, Ingram G, Hogg S. Endwall Profiling with Tip Clearance Flows[R]. ASME 2012-GT-68488.
[22] Mank S, Duerrwaechter L, Hilfer M, et al. Secondary Flows and Fillet Radii in a Linear Turbine Cascade[R]. ASME 2014-GT-25458.
[23] Menter F R, Kuntz M, Langtry R. Ten Years of Industrial Experience with the SST Turbulence Model[J]. Turbulence, Heat and Mass Transfer, 2003, 4(1): 625-632.
[24] Menter F R, Langtry R B, Likki S R, et al. A Correlation-Based Transition Model Using Local Variables—Part I: Model Formulation[J]. Journal of Turbomachinery, 2006, 128(3): 413-422.
[25] Langtry R B, Menter F R. Transition Modeling for General CFD Applications in Aeronautics[R]. AIAA 2005-522.
[26] El Ella H M A, Sjolander S A, Praisner T J. Effects of an Upstream Cavity on the Secondary Flow in a Transonic Turbine Cascade[J]. Journal of Turbomachinery, 2012, 134(5).
[27] Kang K J, Kim T, Song S J. Strengths of Horseshoe Vortices Around a Circular Cylinder with an Upstream Cavity[J]. Journal of Mechanical Science and Technology, 2009, 23(7): 1773-1778.
[28] Sieverding C H. Recent Progress in the Understanding of Basic Aspects of Secondary Flows in Turbine Blade Passages[J]. Journal of Engineering for Gas Turbines and Power, 1985, 107(2): 248-257.
[29] Langston L S. Secondary Flows in Axial Turbines--a Review. [J]. Annals of the New York Academy of Sciences, 2001, 934(1): 11-26.
[30] Dallmann U, Herberg T, Gebing H. Flow Field Diagnostics: Topological Flow Changes and Spatio-Temporal Flow Structure[R]. AIAA 95-0791.
[31] 祝成民, 忻鼎定, 庄逢甘. 利用截面数据显示三维涡结构的新方法[J]. 航空学报, 2003, 24(3): 193-198.　　　　　　　　　　　*　收稿日期:2017-02-16；修订日期:2017-04-12。基金项目:国家自然科学基金资助项目(51576153；51236006)；辽宁重大装备协同创新中心资助。作者简介:于洪石,男,硕士生,研究领域为叶轮机械气动热力学。E-mail: yuhongshi@stu.xjtu.edu.cn通讯作者:席光,男,博士,教授,研究领域为叶轮机械气动热力学。E-mail: xiguang@mail.xjtu.edu.cn(编辑:张荣莉)