畸变气流影响下C-SiC复合材料隔离段稳态特性试验研究

推进技术 ›› 2018, Vol. 39 ›› Issue (10): 2329-2339.

畸变气流影响下C-SiC复合材料隔离段稳态特性试验研究

曹学斌,满延进,李大进,朱守梅,马雪松

北京动力机械研究所激光推进及其应用国家重点实验室，北京 100074,北京动力机械研究所激光推进及其应用国家重点实验室，北京 100074,北京动力机械研究所激光推进及其应用国家重点实验室，北京 100074,北京动力机械研究所激光推进及其应用国家重点实验室，北京 100074,北京动力机械研究所激光推进及其应用国家重点实验室，北京 100074

发布日期:2021-08-15
作者简介:曹学斌，男，博士，高级工程师，研究领域为内流气体动力学。
基金资助:
青年自然科学基金(11502262)。

Experimental Study on Steady-State Characteristics of C-SiC Composite Isolator Considering Effects of Distorted Flow

State Key Laboratory of Laser Propulsion and Application，Beijing Power Machinery Institute，Beijing 100074，China,State Key Laboratory of Laser Propulsion and Application，Beijing Power Machinery Institute，Beijing 100074，China,State Key Laboratory of Laser Propulsion and Application，Beijing Power Machinery Institute，Beijing 100074，China,State Key Laboratory of Laser Propulsion and Application，Beijing Power Machinery Institute，Beijing 100074，China and State Key Laboratory of Laser Propulsion and Application，Beijing Power Machinery Institute，Beijing 100074，China

Published:2021-08-15

摘要/Abstract

摘要： 为了研究畸变气流影响下烧蚀后的C-SiC复合材料隔离段性能，开展了马赫数2.5来流下模拟进气道喉道流场畸变的隔离段直连试验，同时对比研究了光滑不锈钢材质和不同目数砂纸隔离段性能，获得了C-SiC复合材料、不锈钢材质和砂纸隔离段的性能数据。结果表明:(1)烧蚀后的C-SiC隔离段的耐反压能力与光滑不锈钢材质隔离段相比下降了11.7%，总压恢复系数下降了6.96%，与40目砂纸隔离段相比，烧蚀后的C-SiC材料隔离段的耐反压能力和总压恢复系数更低；(2)烧蚀后的C-SiC隔离段性能大幅下降的实质在于表面不平度过大导致激波串前参数的改变，不平度越大，激波串前马赫数就越低，动量损失厚度也就越大，隔离段性能也相应下降更多。

关键词: 隔离段；激波串；畸变；粗糙度

Abstract: In order to investigate the steady-state characteristics of the isolator with surfaces coated with a thermal ablation barrier C-SiC， the direct connect experiments considering the effect of distorted flow were conducted at various back pressures in Mach 2.5 flows. Meanwhile， the other two isolators， one with those surfaces covered with different mesh sandpapers， and one with smooth stainless steel materials， were studied comparatively to obtain the performance of three isolators. It was found that the thermal ablation C-SiC isolator can sustain a lower back pressure before unstarting the flow than the smooth stainless steel isolator about 11.7%， and the total pressure recovery coefficient decreased by 6.96%.Compared to the 40 mesh sandpaper isolator， the isolator equipped with rough thermal ablation C-SiC material exhibits even worse shock holding capability and total pressure recovery. The essence of thermal ablation C-SiC composite impacting the isolator’s performance is the change of flow parameters before shock train because of the high surface roughness. The surface roughness is higher， Mach number before the shock train is lower， and momentum loss thickness is bigger， so the isolator’s performances fell sharply.

Key words: Isolator；Shock train；Distortion；Roughness

曹学斌,满延进,李大进,朱守梅,马雪松. 畸变气流影响下C-SiC复合材料隔离段稳态特性试验研究[J]. 推进技术, 2018, 39(10): 2329-2339.

CAO Xue-bin,MAN Yan-jin,LI Da-jin,ZHU Shou-mei,MA Xue-song. Experimental Study on Steady-State Characteristics of C-SiC Composite Isolator Considering Effects of Distorted Flow[J]. Journal of Propulsion Technology, 2018, 39(10): 2329-2339.

参考文献

[1] Babinsky H, Inger G R. Effect of Surface Roughness on Unseparated Shock-Wave/Turbulent Boundary-Layer Interactions[J]. AIAA Journal, 2002, 40(8): 1567-1573.
[2] Venkata S Krishnamurty, Wei Shyy. Effect of Wall Roughness on the Flow through Converging-Diverging Nozzles[J]. Journal of Propulsion and Power, 1997, 13(6): 753-762.
[3] Lin K C, Tam C J, Eklund D R, et al. Effects of Temperature and Heat Transfer on Shock Train Structures Inside Constant-Area Isolators[R]. AIAA 2006-817.
[4] 高亮杰, 张堃元, 曹学斌, 等. 非对称来流下带粗糙度的隔离段实验研究[R]. CSTAM-2011-2744.
[5] 高亮杰. 非等直截面及复杂环境下隔离段流动特性研究[D]. 南京:南京航空航天大学, 2012.
[6] Saied Emami, Carl A Trexler, Aaron H Auslender, et al. Experimental Investigation of Inlet-Combustion Isolators for a Dual-Mode Scramjet at a Mach Number of 4[R]. NASA-TP-3502.
[7] 张堃元, 王成鹏, 杨建军, 等. 带高超进气道的隔离段流动特性[J]. 推进技术, 2002 , 23 (4): 311-314. (ZHANG Kun- yuan, WANG Cheng-peng, YANG Jian-jun, et al. Investigation of Flow in Isolator of Hypersonic Inlet[J]. Journal of Propulsion Technology, 2002 , 23(4): 311-314.)
[8] Waltrup P J, Billig F S. Structure of Shock Waves in Cylindrical Ducts[J]. AIAA Journal, 1973, 11(10): 1404-1408.
[9] Carroll B F, Dutton J C. Turbulence Phenomena in a Multiple Normal Shock Wave/Turbulent Boundary-Layer Interaction[J]. AIAA Journal, 1992, 30(1): 43-48.
[10] Brandon Morgan, Karthik Duraisamy, Sanjiva K Lele. Large-Eddy and RANS Simulations of a Normal Shock Train in a Constant-Area Isolator[R]. AIAA 2012-1094.
[11] Zachary Vane, Sanjiva K Lele. Simulations of a Normal Shock Train in a Constant Area Duct Using Wall-Modeled LES[R]. AIAA 2013-3204.
[12] Wagner J L, Yuceil K B, Valdivia A, et al. PIV Measurements of the Unstart Process in a Supersonic Inlet/Isolator[R]. AIAA 2008-3849.
[13] 马静. 超燃冲压发动机内流通道冷态流场的PIV试验研究[D]. 南京:南京航空航天大学, 2011.
[14] Hui-jun Tan, Shu Sun. Preliminary Study of Shock Train in a Curved Variable-Section Diffuser[J]. Journal of Propulsion and Power, 2008, 24(2): 245-252.
[15] 李萌, 岳连捷, 张新宇. 隔离段三维流场特性及入射激波对隔离段流场影响的研究[R]. CSTAM-2012-B03-0269.
[16] 曹学斌, 朱守梅, 满延进, 等. 考虑进气道喉道非均匀流场影响的隔离段直连试验[J]. 推进技术, 2015, 36(4): 547-555. (CAO Xue-bin, ZHU Shou-mei, MAN Yan-jin, et al. Direction Connect Test on Isolator Considering Effects of Nonuniform Flow at Inlet Throat[J] . Journal of Propulsion Technology, 2015, 36(4):547-555.)
[17] Cuffel R F, Backf L H. Flow and Heat Transfer Measurements in a Pseudo-Shock Region with Surface Cooling[J]. AIAA Journal, 1976, 14(12): 1716-1722.
[18] Gran R L, Lewis J E, Kubota T. The Effect of Wall Cooling on a Compressible Turbulent Boundary Layer[J]. J.Fluid Mech., 1974, 66(3): 507-528.
[19] Coet M C, Chanetz B. Thermal Effects in Shock Wave/Boundary Layer Interactions in Hypersonic Processes[J]. Recherche Aerospatiale/Aerospace Research, 1994, 4: 251-268.
[20] 卢洪波. 高超声速进气道典型高热负荷区的流动特性研究[D]. 北京:中国科学院大学, 2014.
[21] 曹学斌. 矩形隔离段流动特性及控制规律研究[D]. 南京:南京航空航天大学, 2011.
[22] Ikui T, Matsuo K, Sasaguchi K. Modified Diffusion Model of Pseudo-Shock Waves Considering Upstream Boundary Layers[J]. Bulletin of the Japan Society of Mechanical Engineering, 1981, 24(197): 1920-1927.
[23] 覃奇贤, 刘淑兰. 表面粗糙度[J]. 电镀与精饰. 2009, 31(6):32-34.
[24] 黄亮, 闰维明, 张向东, 等. 北京东六环路面不平度实测及数值模拟[J]. 施工技术, 1986, 28(2): 191-193.
[25] 郑淳之. 国家标准试验筛与美国、西德试验筛的对照[J]. 化工标准与质量监督, 1986, (3).(编辑:史亚红)　　　　　　　　　　　　　*　收稿日期:2016-06-26；修订日期:2016-07-21。基金项目:青年自然科学基金(11502262)。作者简介:曹学斌,男,博士,高级工程师,研究领域为内流气体动力学。E-mail: xuebincao@126.com