二元混压式进气道压缩段性能快速估算及优化

推进技术 ›› 2018, Vol. 39 ›› Issue (11): 2490-2498.

二元混压式进气道压缩段性能快速估算及优化

王宏涛¹,石德平²,刘恒军¹

北京电子工程总体研究所，北京 100854,中国长峰机电技术研究设计院，北京 100854,北京电子工程总体研究所，北京 100854

发布日期:2021-08-15

Rapid Performance Estimation and Optimization for Compression Section of 2D Mixed Compression Inlet

Beijing Institute of Electronic System Engineering，Beijing 100854，China,Changfeng Electromechanical Technology Design Academy，Beijing 100854，China and Beijing Institute of Electronic System Engineering，Beijing 100854，China

Published:2021-08-15

摘要/Abstract

摘要： 冲压动力导弹的进气道性能决定了导弹动力系统的优劣，因此在冲压动力导弹设计初期，有必要对二元混压式进气道超声速压缩段性能进行快速估算及优化。针对该问题，提出将进气道外形进行参数化建模，建立基于特征线及边界层理论的进气道性能快速估算方法，并通过激波边界层干扰分离指标变量以及喉道流动参数二次修正，提高对进气道性能估算的精度。估算结果与CFD计算结果的对比，表明了该方法可以对设计状态下二元混压式进气道超声速压缩段阻力系数、平均总压恢复系数及流量系数进行具有较高精度的快速估算，最大误差不超过1.5%。此外该方法与遗传优化算法结合，对进气道超声速压缩段外形设计参数进行快速优化，使进气道压缩段阻力系数下降了13.8%，表明该结合方法可在冲压动力导弹设计初期阶段提高二元混压式进气道的性能。

关键词: 二元混压式进气道；超声速压缩段；特征线法；快速估算；优化设计

Abstract: The performance of inlet plays a key role in the propulsive system of ramjet-powered missile. Therefore， the rapid estimation and optimization of the performance of the 2D mixed compression inlet are necessary in the preliminary design of ramjet-powered missile. In order to solve this problem， a parametric model of the supersonic compression section of 2D mixed compression inlet was used. Based on the method of characteristics and boundary layer theory， a method which can rapidly estimate the drag coefficient， average total pressure recovery coefficient and mass flow coefficient of the supersonic compression section of inlet under design condition was put forward. Meantime， to improve the accuracy of the estimation method， a correction which used shock wave boundary layer interference index variable and flow parameters at throat was adopted. In contrast to Computational Fluid Dynamics， the results using rapid estimation method have high accuracy and high efficiency with maximum error less than 1.5%. Besides， the supersonic compression section of 2D mixed compression inlet could be optimized by using the rapid estimation method and the genetic algorithm to reduce the drag coefficient by 13.8%. It showed combination can improve the performance of the 2D mixed compression inlet in the preliminary design of ramjet-powered missile.

Key words: Two-dimensional mixed compression inlet；Supersonic compression section；Method of characteristics；Rapid estimation；Optimization

王宏涛,石德平,刘恒军. 二元混压式进气道压缩段性能快速估算及优化[J]. 推进技术, 2018, 39(11): 2490-2498.

WANG Hong-tao¹,SHI De-ping²,LIU Heng-jun¹. Rapid Performance Estimation and Optimization for Compression Section of 2D Mixed Compression Inlet[J]. Journal of Propulsion Technology, 2018, 39(11): 2490-2498.

参考文献

[1] 王起飞, 苗永强. 流星空空导弹战术技术性能分析[J]. 航空兵器, 2004, (5): 5-8.
[2] 商旭升, 何宇峰, 李垠广, 等. TBCC发动机用二级混压式进气道压缩段设计方法研究[J]. 推进技术, 2015, 36(3): 365-371. (SHANG Xu-sheng, HE Yu-feng, LI Yin-guang, et al. Design Method of Two-Step Hypersonic Mixed Compression Inlet in Condensability Segment for TBCC Engine[J]. Journal of Propulsion Technology, 2015, 36(3): 365-371.)
[3] 徐旭, 陈兵, 徐大军. 冲压发动机原理及技术[M]. 北京:北京航空航天大学出版社, 2014.
[4] 郭荣荣, 金志光, 李猛, 等. 二元外并联RBCC进气道变几何方案研究[J]. 推进技术, 2017, 38(3): 481-488. (GUO Rong-rong, JIN Zhi-guang, LI Meng, et al. Investigation of a 2D Variable Geometry over/under Type Inlet for RBCC[J]. Journal of Propulsion Technology, 2017, 38(3): 481-488.)
[5] 李祝飞, 高文智, 杨基明. 一种二元进气道起动特性的数值与实验考察[J]. 推进技术, 2016, 37(7): 1224-1232. (LI Zhu-fei, GAO Wen-zhi, YANG Ji-ming. Numerical and Experimental Investigation for Starting Characteristics of a Two-Dimensional Inlet [J]. Journal of Propulsion Technology, 2016, 37(7): 1224-1232.)
[6] 邓隆范, 李国雄, 成楚之. 二元混压式超声速进气道性能预估及优化设计[J]. 现代防御技术, 2002, 30(5): 25-29.
[7] 周建兴, 朴英, 曹志松. 基于混合遗传算法的进气道性能设计与优化[J]. 计算机工程, 2008, 34(12):233-235.
[8] 郭应钧. 超声速进气道流场和边界层计算[J] . 空气动力学学报, 1990, 8(1): 104-109.
[9] XIE Wen-zong, GE Yan, CHEN Hao, et al. Rapid Supersonic Performance Prediction for 2D Ramjet Inlets[J]. Aerospace Science and Technology, 2016, 53: 220-231.
[10] 游进, 刘冰, 夏智勋, 等. 某弹用二元混压式超声速进气道型面优化设计[C]. 北京:中国宇航协会固体火箭推进第22届年会(发动机分册), 2005.
[11] 吴子牛. 空气动力学[M]. 北京:清华大学出版社, 2007.
[12] 童秉纲, 孔祥言, 邓国华. 气体动力学[M]. 北京:高等教育出版社, 2007.
[13] Zucrow M J, Hoffmann J D. Gas Dynamics[M]. New York: John Wiley and Sons Inc.Press, 1976.
[14] 李泳洲. 马赫数分布可控的高超声速内收缩进气道机器一体化设计研究[D]. 南京:南京航空航天大学, 2014.
[15] 姜贵庆, 刘连元. 高速气流传热与烧蚀热防护[M]. 北京:国防工业出版社, 1999.
[16] Mahoney J John. Inlets for Supersonic Missiles[M]. USA: AIAA Education Series, 1990.
[17] Sasman P K, Cresci R J. Compressible Turbulent Boundary Layer with Pressure Gradient and Heat Transfer [J]. AIAA Journal, 1965, 4(1).
[18] Souverein L J, Bakker P G, Dupont P. A Scaling Analysis for Turbulent Shock-Wave/Boundary-Layer Interactions[J]. Journal of Fluid Mechanics, 2013, 714(1): 505-535.
[19] 雷英杰, 张善文. MATLAB遗传算法工具箱及应用[M]. 西安:西安电子科技大学出版社, 2013.　　　　　　　　　　　　　　收稿日期:2017-10-09；修订日期:2017-11-02。通讯作者:王宏涛,男,博士生,研究领域为飞行器总体设计。E-mail: 381094332@qq.com(编辑:史亚红)