基于轮毂静压的非轴对称端壁造型

推进技术 ›› 2018, Vol. 39 ›› Issue (11): 2608-2614.

基于轮毂静压的非轴对称端壁造型

唐海兵¹,余又红¹,李钰洁^1,2

海军工程大学动力工程学院，湖北武汉 430033,海军工程大学动力工程学院，湖北武汉 430033,海军工程大学动力工程学院，湖北武汉 430033; 海军工程大学舰船动力工程军队重点实验室，湖北武汉 430033

发布日期:2021-08-15
作者简介:唐海兵，男，硕士生，研究领域为压气机气动热力学。E-mail: tanghb14@163.com 通讯作者:余又红，男，博士，副教授，研究领域为燃气轮机气动热力学。
基金资助:
国防创新基金(17-163-13-ZT-008-033-01)。

Non-Axisymmetric Endwall Profiling Based on Hub Static Pressure

College of Power Engineering，Naval University of Engineering，Wuhan 430033，China,College of Power Engineering，Naval University of Engineering，Wuhan 430033，China and College of Power Engineering，Naval University of Engineering，Wuhan 430033，China;Military Key Laboratory for Naval Ship Power Engineering，Naval University of Engineering，Wuhan 430033，China

Published:2021-08-15

摘要/Abstract

摘要： 为探究非轴对称端壁减小流动损失的机理，根据非轴对称端壁造型基本原理，提出了一种基于轮毂静压构造非轴对称端壁的方法。以Rotor37为研究对象，采用NUMECA/Auto- Blade和Design3d进行端壁造型和优化，并使用EURANUS流场求解器进行数值计算，分析了造型后端壁对压气机转子总体性能的影响。结果表明:基于轮毂静压的非轴对称端壁能有效减小叶片通道的横向压差，抑制气流在吸力面出现过早分离，且叶片表面的压力分布更加均匀，叶片出口总压损失系数降低了8.94%，证实了基于轮毂静压构造非轴对称端壁方法的有效性。

关键词: 非轴对称端壁；压气机转子；轮毂静压；端壁造型

Abstract: In order to explore the mechanism of non-axisymmetric endwall reducing flow losses， a method in accordance with hub static pressure was proposed， which was based on the principle of non-axisymmetric endwall profiling. This paper takes Rotor37 as the research object， NUMECA/Auto-Blade， Design3d and EURANUS flow solver were carried out to make the endwall， optimization and numerical calculation respectively. The effects of the overall performance of compressor rotor with profiled endwall were analyzed. Results indicate that the non-axisymmetric endwall based on hub static pressure can effectively reduce the transverse pressure gradient of the blade passage， inhibit the premature separation appearing on the suction surface. In addition， the distribution of blade surface pressure becomes more uniform， and the blade exit total pressure loss coefficient is reduced by 8.94%. Thus， the profiling method based on hub static pressure was proved to be effective.

Key words: Non-axisymmetric endwall；Compressor rotor；Hub static pressure；Endwall profiling

唐海兵,余又红,李钰洁. 基于轮毂静压的非轴对称端壁造型[J]. 推进技术, 2018, 39(11): 2608-2614.

TANG Hai-bing¹,YU You-hong¹,LI Yu-jie^1,2. Non-Axisymmetric Endwall Profiling Based on Hub Static Pressure[J]. Journal of Propulsion Technology, 2018, 39(11): 2608-2614.

参考文献

[1] 那振喆, 刘波, 高丽敏. 高压涡轮导叶非轴对称端壁优化设计[J]. 航空工程进展, 2013, 4(3): 319-326.
[2] Morris A W H, Hoare R G. Secondary Loss Measurements in a Cascade of Turbine Blades with Meridional Wall Profiling[J]. Mechanical Engineering, 1976, 98(2).
[3] Germain T, Nagel M, Raab I, et al. Improving Efficiency of a High Work Turbine Using Non-Axisymmetric Endwalls PartI: Endwall Design and Performance[R]. ASME 2008 GT-50469.
[4] Boletis E. Effects of Tip Endwall Contouring on the Three-Dimensional Flow Investigation[J]. Journal of Engineering for Gas Turbines and Power, 1985, 107(4): 983-990.
[5] Atkins M J. Secondary Losses and Endwall Profiling in a Turbine Cascade[R]. IMech E C 255/87, 1987: 225-226.
[6] Rose M G. Non-Axisymmetric Endwall Profiling in the HP NGVs of an Axial Flow Gas Turbine[R]. ASME 94-GT-249.
[7] Harvey N W, Rose M G, Taylor M D. Non-Axisymmetic Turbine End Wall Design, Part I: Three-Dimensional Linear Design System[R]. ASME 99-GT-337.
[8] Hartland J C, Gregory-Smith G, Harvey N W, et al. Non-Axisymmetric Turbine End Wall Design: Part II Experimental Validation[R]. ASME 99-GT-338.
[9] Shahpar S, Lapworth B L. A Forward and Inverse Three- Dimensional Linear Design System for Turbomachinery Applications[C]. Athens: 4th ECCOMASS Computational Fluid Dynamics Conference, 1998.
[10] Brennan G, Harvey N W, Rose M G. Improving the Efficiency of the Trent 500-HP Turbine Using Nonaxisymmetric End Walls, Part I: Turbine Design[R]. ASME 2001 GT-0505.
[11] Nagel M G, Fottner L, BaierR. Optimization of Three Dimensionally Designed Turbine Blades and Side Walls[R]. ISABE-2001-1058.
[12] 李国君, 马晓永, 李军. 非轴对称端壁成型及其对叶栅损失影响的数值研究[J]. 西安交通大学学报, 2005, 39(11): 1169-1172.
[13] 李国君, 郑金, 李军, 等. 一种新非轴对称端壁成型方法的数值研究[J]. 航空动力学报, 2007, 22(9).
[14] 孙皓, 宋立明, 李军, 等. 小展弦比叶栅非轴对称端壁造型及气动性能的数值研究[J]. 航空工程进展, 2012, 46(11): 6-11.
[15] 田兴江, 常海萍, 张镜洋, 等. 基于参数化脊线的非轴对称端壁成型方法[J]. 推进技术, 2017, 38(6): 1294-1301. (TIAN Xing-jiang, CHANG Hai-ping, ZHANG Jing-yang, et al. Non-Axisymmetric Endwall Contouring Method Based on Parameterized Ridge Line[J]. Journal of Propulsion Technology, 2017, 38(6): 1294-1301.)
[16] 孙皓, 李军, 李国君, 等. 非轴对称端壁造型技术在透平机械中的应用和发展[C]. 西安:西安交通大学, 2011.
[17] 高增珣, 高学林, 袁新. 透平叶栅非轴对称端壁的气动最优化设计[J]. 工程热物理学报, 2007, 28 (4).
[18] 张鹏, 刘波, 毛晓晨, 等. 三维造型和非轴对称端壁在跨声速压气机中的应用[J]. 推进技术, 2016, 37(2): 250-257. (ZHANG Peng, LU Bo, MAO Xiao-chen, et al. Application of 3D Blading and Non-Axisymmetric Endwall in a Transonic Compressor[J]. Journal of Propulsion Technology, 2016, 37(2):250-257.)
[19] 赵刚剑, 刘波, 那振喆, 等. 采用新型非轴对称端壁优化设计方法提高涡轮性能的数值研究[J]. 推进技术, 2014, 35(5): 597-602. (ZHAO Gang-jian, LIU Bo, NA Zhen-zhe, et al. Improving the Performance of Turbine Based on a New Optimization Design Method[J]. Journal of Propulsion Technology, 2014, 35(5): 597-602.)
[20] Reid L, Moore R D. Design and Overall Performance of Four Highly Loaded, High-Speed Inlet Stages for an Advanced High-Pressure-Ratio Core Compressor[R]. NASA- TP-1337, 1978.
[21] Ali A. A. NASA Rotor 37 CFD Code Validation Glenn-HT Code[R]. AIAA 2009-1060.
[22] 赵辛午. 基于遗传算法的压气机三维气动优化设计方法研究[D]. 哈尔滨:哈尔滨工业大学, 2008.　　　　　　　　　　　　　　收稿日期:2018-02-07；修订日期:2018-03-28。基金项目:国防创新基金(17-163-13-ZT-008-033-01)。作者简介:唐海兵,男,硕士生,研究领域为压气机气动热力学。E-mail: tanghb14@163.com通讯作者:余又红,男,博士,副教授,研究领域为燃气轮机气动热力学。E-mail: wtuyyh@163.com(编辑:史亚红)