稠密粒子流作用下三元乙丙绝热材料烧蚀性能分析

推进技术 ›› 2018, Vol. 39 ›› Issue (12): 2845-2852.

稠密粒子流作用下三元乙丙绝热材料烧蚀性能分析

许团委¹,陆贺建¹,王健儒¹,刘洋²

西安航天动力技术研究所，陕西西安 710025,西安航天动力技术研究所，陕西西安 710025,西安航天动力技术研究所，陕西西安 710025,西北工业大学，航天学院，陕西西安 710072

发布日期:2021-08-15

Analysis of Dense Particle Stream on Ablation Properties of EPDM Insulation

Institute of Xi’an Aerospace Solid Propulsion Technology，Xi’an 710025，China,Institute of Xi’an Aerospace Solid Propulsion Technology，Xi’an 710025，China,Institute of Xi’an Aerospace Solid Propulsion Technology，Xi’an 710025，China and College of Astronautics，Northwestern Polytechnical University，Xi’an 710072，China

Published:2021-08-15

摘要/Abstract

摘要： 为研究稠密粒子流作用下三元乙丙绝热层材料TI117的烧蚀性能，采用基于地面模拟试验发动机完成了18发烧蚀试验。通过分析试验数据，认为针对TI117绝热材料存在一个粒子冲刷速度临界值[vcri]=28m/s，当粒子流速度小于[vcri]时，粒子流状态参数对绝热层炭化烧蚀影响较小，当粒子流速度大于[vcri]时绝热层烧蚀率随粒子冲刷速度的增加增幅较快，粒子冲刷角度的影响也显著。通过分析颗粒浓度、冲刷速度和角度等随烧蚀试验状态的变化规律，结合试验数据进行回归分析，给出了三元乙丙绝热材料TI117在两种冲刷状态下的烧蚀率工程预示模型。通过分析芳纶纤维铺设方向对TI117绝热层烧蚀的影响，认为两种铺设方向下烧蚀结果基本一致，严酷条件下芳纶纤维垂直铺设优于平行铺设。

关键词: 固体发动机；稠密粒子流；EPDM绝热层；烧蚀

Abstract: In order to study the ablation properties of EPDM insulation material TI117 impacting with the dense particle flow in solid rocket motor， the insulation ablation experiment is conducted 18 times based on the ground test motor. Though analyzing the experimental data， there is a particle scour critical velocity， [vcri]=28m/s， when the particle scour velocity below [vcri]， the ablation rate increases slowly with the particle flow parameters， when the particle scour velocity above [vcri]， the ablation rate increases rapidly with the particle scour velocity and the particle scour angle. Through the analysis of the changing law of particle concentration， scouring velocity and angle with the ablation experiment condition， a engeering prediction model with two conditions for TI117 insulation ablation is proposed though regression analysis with experimental condition data. Through analyzing the effect of aramid fibers orientation in TI117 insulation， it is found that the linear ablation rates are almost same for aramid fibers with different orientation mode. Under harsh conditions， the aramid fibers with vertical orientation is better than parallel orientation mode.

Key words: Solid rocket motor；Dense particle stream；EPDM material；Ablation

许团委,陆贺建,王健儒,刘洋. 稠密粒子流作用下三元乙丙绝热材料烧蚀性能分析[J]. 推进技术, 2018, 39(12): 2845-2852.

XU Tuan-wei¹,LU He-jian¹,WANG Jian-ru¹,LIU Yang². Analysis of Dense Particle Stream on Ablation Properties of EPDM Insulation[J]. Journal of Propulsion Technology, 2018, 39(12): 2845-2852.

参考文献

[1] 秦锋, 张崇耿, 张新航, 等. 耐烧蚀三元乙丙橡胶绝热层材料的性能研究[J]. 制造技术研究, 2010, (3): 26-28.
[2] 邢志浩, 刘燕宾, 王虎干, 等. 过载条件下固体火箭发动机内流场及绝热层烧蚀研究[J]. 航空兵器, 2013, (4): 38-40.
[3] 田维平, 许团委, 王建儒. 过载下燃烧室粒子特性与绝热层烧蚀研究进展[J]. 固体火箭技术, 2015, 38(1):30-36.
[4] 刘洋, 吴育飞, 李江, 等. 长时间小过载下发动机流场特征及绝热层烧蚀分析[J]. 推进技术, 2013, 34(8): 1071-1076. (LIU Yang, WU Yu-fei, LI Ji-ang, et al. Flow Field and Ablation Mode Analysis of Insulator under Low Acceleration with Long Operation Time Condition for Solid Rocket Motor[J]. Journal of Propulsion Technology, 2013, 34( 8): 1071-1076.)
[5] 高国新, 郑元锁, 孙婕, 等. 有机纤维/EPDM 绝热材料性能研究[J]. 固体火箭技术, 2007, 30(6): 544-547.
[6] 张中水, 许进升, 陈雄. 基于EPDM绝热层拉压不同性的研究[J]. 化工新型材料, 2013, 43(3): 170-172.
[7] 曹军, 房雷. 三元乙丙橡胶绝热层的烧蚀特性研究[J]. 航空兵器, 2015, (2): 46-49.
[8] 许团委, 田维平, 王建儒. 中、小过载下战术发动机内流场数值模拟[J]. 推进技术, 2015, 36(4): 532-539. (XU Tuan-wei, TIAN Wei-ping, WANG Jian-ru.Numerical Simulation of Flow Field of Tactical SRM with Low and Medium Acceleration[J]. Journal of Propulsion Technology, 2015, 36(4): 532-539.)
[9] Kovalev Oleg B. Motor and Plume Particle Size Prediction in Solid-Propellant Rocket Motors[J]. Journal of Propulsion and Power, 2002, 18(6).
[10] 何国强, 王国辉, 蔡体敏, 等. 过载条件下固体发动机内流场数值模拟[J]. 推进技术, 2002, 23(3): 182-185. (HE Guo-qiang, WANG Guo-hui, CAI Ti-min, et al. Numerical Simulation on 3-D Two-Phase Flow Field in SRM with Acceleration Load[J]. Journal of Propulsion Technology, 2002, 23(3): 182-185.)
[11] 张承志, 李江, 刘洋, 等. 颗粒冲刷条件对绝热材料烧蚀过程的影响研究[J]. 固体火箭技术, 2013,36(2): 200-205.
[12] 许团委, 田维平, 王建儒. 固体发动机地面过载试验凝相粒子加速度分析[J]. 固体火箭技术, 2014, 37(4): 486-489.
[13] LI Jiang, LIU Yang, LOU Yong-chun, et al. Experimental Investigation for the Influence of Particle on Insulation Erosion[J]. Journal of Propulsion Technology, 2006, 27(1): 71-74.
[14] 王娟, 李江, 刘洋, 等. 模拟过载条件下EPDM绝热层烧蚀实验[J]. 推进技术, 2010, 31(4):618-622. (WANG Juan, LI Jiang, LIU Yang, et al. Experiment on Ablation of EPDM Insulator Simulating Overload Condition[J]. Journal of Propulsion Technology, 2010, 31(4): 618-622.)
[15] 徐义华, 胡春波, 李江. 粒子侵蚀下三元乙丙绝热材料炭化层破坏特性实验研究[J]. 工程力学, 2011, 28(5): 251-256.
[16] 凌玲, 陈德宏, 陈梅, 等. 芳纶纤维对EPDM绝热层力学行为的影响[J]. 固体火箭技术, 2016, 39(4): 555-559.　　　　　　　　　　　　　　收稿日期:2017-09-28；修订日期:2018-01-10。通讯作者:许团委,男,博士,研究领域为固体火箭发动机总体设计。E-mail: xutuanwei525@163.com(编辑:朱立影)