叶顶凹槽间隙气膜冷却的传热数值研究

推进技术 ›› 2018, Vol. 39 ›› Issue (3): 575-582.

叶顶凹槽间隙气膜冷却的传热数值研究

周治华,陈绍文,李伟航,崔涛,王松涛

哈尔滨工业大学能源科学与工程学院，黑龙江哈尔滨 150001,哈尔滨工业大学能源科学与工程学院，黑龙江哈尔滨 150001,哈尔滨工业大学能源科学与工程学院，黑龙江哈尔滨 150001,哈尔滨工业大学能源科学与工程学院，黑龙江哈尔滨 150001,哈尔滨工业大学能源科学与工程学院，黑龙江哈尔滨 150001

发布日期:2021-08-15
作者简介:周治华，男，博士生，研究领域为叶轮机械内流动。
基金资助:
国家自然科学基金创新研究群体项目(51121004)；国家自然科学基金(51206035)。

eat Transfer Numerical Research on Film Cooling of Tip Groove Clearance

Energy Science and Engineering School，Harbin Institute of Technology，Harbin 150001，China,Energy Science and Engineering School，Harbin Institute of Technology，Harbin 150001，China,Energy Science and Engineering School，Harbin Institute of Technology，Harbin 150001，China,Energy Science and Engineering School，Harbin Institute of Technology，Harbin 150001，China and Energy Science and Engineering School，Harbin Institute of Technology，Harbin 150001，China

Published:2021-08-15

摘要/Abstract

摘要： 采用三维气热耦合数值模拟方法，分析了凹槽间隙底面受到泄漏流冲击的流动特性，对气膜冷却参数对凹槽间隙气膜冷却换热效果的影响进行了研究，探讨了吹风比、冷却孔位置、冷却孔角度对壁面换热的影响，并结合三维流固耦合计算，研究了叶顶气膜冷却方式对叶顶表面传热的影响。结果表明，冷却孔位于间隙流动冲击凹槽底面上游位置能有效降低壁面Nu数，获得较低的叶片表面平均温度，此时大吹风比效果更好；所选取的冷却方式使得E3高压涡轮第一级动叶的最大无量纲温度降低了0.156。

关键词: 涡轮动叶；叶顶凹槽；间隙泄漏流；气膜冷却；气热耦合

Abstract: Using a three dimensional conjugate heat transfer numerical simulation，the clearance flow characteristics of groove bottom by the impact of leakage flow was analyzed. Then the effects of film cooling parameters on heat transfer efficiency with groove-clearance film cooling were studied. The influence of the location，angle，blowing ratio of the cooling hole on the wall heat transfer was discussed. And combined with three dimensional fluid-structure interaction simulations，the influence of blade-tip film cooling on heat transfer of tip surface was studied. The results show that the cooling hole in the upstream position of groove bottom with clearance flow impact can effectively reduce the wall Nusselt number. A lower average temperature of the blade surface is obtained and the large blowing ratio is better. The selected cooling system makes the peak non-dimensional temperature decrease of 0.156 for the first-stage rotor of E3 high pressure turbine.

Key words: Turbine rotor；Tip groove；Clearance leakage flow；Film cooling；Conjugate heat transfer

周治华,陈绍文,李伟航,崔涛,王松涛. 叶顶凹槽间隙气膜冷却的传热数值研究[J]. 推进技术, 2018, 39(3): 575-582.

ZHOU Zhi-hua,CHEN Shao-wen,LI Wei-hang,CUI Tao,WANG Song-tao. eat Transfer Numerical Research on Film Cooling of Tip Groove Clearance[J]. Journal of Propulsion Technology, 2018, 39(3): 575-582.

参考文献

[1] Metzger D E, Bunker R S, Chyu M K. Cavity Heat Transfer on a Transverse Grooved Wall in a Narrow Flow Channel[J]. Journal of Heat Transfer, 1989, 111(1): 73-79.
[2] Goldstein R J. Film Cooling[J]. Advances in Heat Transfer, 1971, 7: 321-379.
[3] Goldstein R J, Eckert E R G, Burggraf F. Effects of Hole Geometry and Density on Three-Dimensional Film Cooling[J]. International Journal of Heat and Mass Transfer, 1974, 17(5): 595-607.
[4] Pedersen D R, Eckert E R G, Goldstein R J. Film Cooling with Large Density Differences Between the Mainstream and the Secondary Fluid Measured by the Heat-Mass Transfer Analogy[J]. Journal of Heat Transfer, 1977, 99(4): 620-627.
[5] Kim Y W, Metzger D E. Heat Transfer and Effectiveness on Film Cooled Turbine Blade Tip Models [J]. Journal of Turbomachinery, 1995, 117(1): 12-21.
[6] Wang Z, Zhang Q, Liu Y, et al. Impact of Cooling Injection on the Transonic Over-Tip Leakage Flow and Squealer Aerothermal Design Optimization[J]. Journal of Engineering for Gas Turbines and Power, 2015, 137(6): 062603.
[7] 虞跨海, 杨茜, 岳珠峰. 高压涡轮冷却叶片叶顶结构气动与传热[J]. 推进技术, 2012, 33(2): 174-178. (YU Kua-hai, YANG Xi, YUE Zhu-feng. Aerodynamic and Heat Transfer of Cooling Blade Tips for High Pressure Turbine[J]. Journal of Propulsion Technology, 2012, 33(2): 174-178.)
[8] Ma H, Zhang Q, He L, et al. Cooling Injection Effect on a Transonic Squealer Tip, Part 2: Analysis of Aerothermal Interaction Physics[R]. ASME GT 2016-57587.
[9] Zhou C. Thermal Performance of Transonic Cooled Tips in a Turbine Cascade [J]. Journal of Propulsion and Power, 2015, 31(5): 1268-1280.
[10] 周凯, 周超, 钟芳盼. 跨声速叶栅中气膜冷却对平面叶尖流动和传热特性的影响[J]. 航空动力学报. 2013, 28(11): 2440-2447.
[11] Newton P J, Lock G D, Krishnababu S K, et al. Aerothermal Investigations of Tip Leakage Flow in Axial Flow Turbines, Part III: TIP Cooling [J]. Journal of Turbomachinery, 2008, 131(1): 011008.
[12] Yang D L, Feng Z P, Yu X. Investigation of Film Cooling Effectiveness on Squealer Tip of a Gas Turbine Blade[R]. ASME GT 2009-60280.
[13] 杜昆, 宋立明, 李军. 凹槽状叶顶涡轮叶片传热特性的数值研究[J]. 推进技术, 2014, 35(5): 618-623. (DU Kun, SONG Li-ming, LI Jun. Numerical Investigations on Heat Transfer Characteristics of Turbine Blade with Squealer Tip[J]. Journal of Propulsion Technology, 2014, 35(5): 618-623.)
[14] 李军, 王金山, 蒋勇, 等. 凹槽状动叶顶部非定常气膜冷却性能的研究[J]. 西安交通大学学报, 2010, 44(5): 5-10.
[15] Arisi A, Phillips J, Ng W F, et al. An Experimental and Numerical Study on the Aerothermal Characteristics of a Ribbed Transonic Squealer-Tip Turbine Blade with Purge Flow[R]. ASME GT 2016-43073.
[16] 王志多, 刘兆方, 丰镇平. 不同湍流模型对燃气透平静叶及动叶叶顶传热预测精度的研究[J]. 工程热物理学报, 2015, 36(9): 1894-1897.
[17] Wang Z D, Liu Z F, Feng Z P. Influence of Mainstream Turbulence Intensity on Heat Transfer Characteristics of a High Pressure Turbine Stage with Inlet Hot Streak[J].Journal of Turbomachinery, 2015, 138(4).
[18] Yang D L, Yu X B, Feng Z P. Investigation of Leakage Flow and Heat Transfer in a Gas Turbine Blade Tip with Emphasis on the Effect of Rotation[J]. Journal of Turbomachinery, 2010, 132(4).　　　　　　　　　　　　　*　收稿日期:2016-09-26；修订日期:2016-11-14。基金项目:国家自然科学基金创新研究群体项目(51121004)；国家自然科学基金(51206035)。作者简介:周治华,男,博士生,研究领域为叶轮机械内流动。E-mail: zhouzhihua528@163.com(编辑:史亚红)