基于改进Taguchi方法的航空发动机装配成功率计算方法

推进技术 ›› 2018, Vol. 39 ›› Issue (3): 653-659.

基于改进Taguchi方法的航空发动机装配成功率计算方法

陈志英,刘勇,周平,刘广通

北京航空航天大学能源与动力工程学院，北京 100191,北京航空航天大学能源与动力工程学院，北京 100191,北京航空航天大学能源与动力工程学院，北京 100191,北京航空航天大学能源与动力工程学院，北京 100191

发布日期:2021-08-15
作者简介:陈志英，男，博士，教授，研究领域为航空发动机结构优化设计、可靠性及维修性工程。
基金资助:
国家自然科学基金(51275024)。

Assembly Success Rate Calculation Method for Aero-Engine Based on Improved Taguchi Method

School of Energy and Power Engineering，Beihang University，Beijing 100191，China,School of Energy and Power Engineering，Beihang University，Beijing 100191，China,School of Energy and Power Engineering，Beihang University，Beijing 100191，China and School of Energy and Power Engineering，Beihang University，Beijing 100191，China

Published:2021-08-15

摘要/Abstract

摘要： 考虑到运用传统的Taguchi方法在进行公差分析和装配成功率计算时，在计算精度上的不足，无法满足航空发动机研制过程中公差设计高精度、高效率、短周期、多组成环等要求。针对该问题，文中提出一种基于改进的Taguchi方法的装配成功率计算模型。利用改进的Taguchi方法对统计数据的前四阶矩进行计算，并结合Pearson分布理论建立装配成功率的计算模型。在理论分析的基础上，以某型航空发动机涡轮转子的装配成功率为例进行计算。结果表明:与蒙特卡洛仿真结果对比，改进的Taguchi方法在对装配间隙的峰度进行估计时使相对误差由原来的19.38%降低到0.21%；用本文所提方法得出的装配成功率与蒙特卡洛仿真结果的相对误差仅为0.02%，计算结果验证了该方法的有效性。

关键词: 航空发动机；公差分析；Taguchi方法；Pearson分布族；装配成功率

Abstract: The calculation accuracy of traditional Taguchi method is not high enough to support assembly tolerance analysis and assembly success rate estimation， which could not adapt to the demand of high-precision， high-efficiency， short-cycle， multi-assembly dimensions of tolerance design in the manufacturing process of aero-engine. Aiming at this problem， a kind of assembly success rate calculation model based on improved Taguchi method is proposed. Combined with Pearson distribution theory， this calculation model is set up by using the improved Taguchi method to calculate the first four moments of statistics. On the basis of theoretical analysis， the proposed method is applied to calculate a turbine rotor’s assembly success rate. The results show that compared with Monte Carlo simulation results， the improved Taguchi method reduces the relative error from the original 19.38% to 0.21% when estimating the kurtosis of the assembly gap， and the relative error of the assembly success rate obtained by the proposed method is 0.02%， and the effectiveness of the proposed method is verified.

Key words: Aero-engine；Tolerance analysis；Taguchi method；Pearson distribution family；Assembly success rate

陈志英,刘勇,周平,刘广通. 基于改进Taguchi方法的航空发动机装配成功率计算方法[J]. 推进技术, 2018, 39(3): 653-659.

CHEN Zhi-ying,LIU Yong,ZHOU Ping,LIU Guang-tong. Assembly Success Rate Calculation Method for Aero-Engine Based on Improved Taguchi Method[J]. Journal of Propulsion Technology, 2018, 39(3): 653-659.

参考文献

[1] McDonald C F, Massardo A F, Rodgers C, et al. Recuperated Gas Turbine Aeroengines, Part II: Engine Design Studies Following Early Development Testing[J]. Aircraft Engineering and Aerospace Technology, 2008, 80(3): 280-294.
[2] Fei C, Bai G. Distributed Collaborative Extremum Response Surface Method for Mechanical Dynamic Assembly Reliability Analysis[J]. Journal of Central South University, 2013, 20: 2414-2422.
[3] Yang Z, Hussain T, Popov A A, et al. Novel Optimization Technique for Variation Propagation Control in an Aero-Engine Assembly[J]. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 2011, 225(1): 100-111.
[4] 费成巍, 白广忱, 范觉超, 等. 涡轮转子多尺寸装配可靠性优化分析[J]. 推进技术, 2013, 34(1): 15-18. (FEI Cheng-wei, BAI Guang-chen, FAN Jue-chao, et al. Optimization and Analysis for Multi-Dimensions Assembly Reliability of Turbine Rotor[J]. Journal of Propulsion Technology, 2013, 34(1): 15-18.)
[5] 桑潇潇, 廖明夫, 吴法勇, 等. 发动机轴承内环装配工艺对转子动力学特性影响的试验研究[J]. 推进技术, 2015, 36(12): 1874-1880. (SANG Xiao-xiao, LIAO Ming-fu, WU Fa-yong, et al. Experimental Study on Rotor-Dynamic Behavior Development on Aero-Engine Bearing Inner Ring Assembly Technologies[J]. Journal of Propulsion Technology, 2015, 36(12): 1874-1880.)
[6] Feng C X J, Kusiak A. Robust Tolerance Synthesis with the Design of Experiments Approach[J]. Journal of Manufacturing Science and Engineering, 2000, 122(3): 520-528.
[7] 邵锦文, 张振家, 袁宁, 等. 航空发动机涡轮叶尖间隙损失的统计设计[J]. 推进技术, 2003, 24(2):122-124. (SHAO Jin-wen, ZHANG Zhen-jia, YUAN Ning, et al. Statical Design for Turbine Blades Tip Clearance Loss Analysis[J]. Journal of Propulsion Technology, 2003, 24(2): 122-124.)
[8] 石宏. 航空发动机装配工艺技术[M]. 北京:北京航空航天大学, 2015: 28-30.
[9] Singh P K, Jain P K, Jain S C. Important Issues in Tolerance Design of Mechanical Assemblies, Part 1: Tolerance Analysis[J]. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 2009, 223(10): 1225-1247.
[10] 朱彬, 于乃江, 孟祥海, 等. 航空发动机装配尺寸链公差设计方法研究[J]. 测试技术学报, 2015, 29(2): 177-184.
[11] 张岩, 莫蓉. 基于低偏差序列样本的装配公差分析方法[J]. 计算机集成制造系统, 2014, 20(3): 579-585.
[12] Tian M W, Shi R C J. Worst Case Tolerance Analysis of Linear Analog Circuits Using Sensitivity Bands[J]. IEEE Transactions on Circuits and Systems I: Fundamental Theory and Applications, 2000, 47(8): 1138-1145.
[13] Mansuy M, Giordano M, Hernandez P. A New Calculation Method for the Worst Case Tolerance Analysis and Synthesis in Stack-Type Assemblies[J]. Computer-Aided Design, 2011, 43(9): 1118-1125.
[14] Yan-long CAO, Jiang-xin Y, Zhao-tong WU, et al. A Robust Tolerance Design Method Based on Process Capability[J]. Journal of Zhejiang University-Science A, 2004, 5(1): 81-85.
[15] Cao Y, Yan H, Liu T, et al. Application of Quasi-Monte Carlo Method Based on Good Point Set in Tolerance Analysis[J]. Journal of Computing and Information Science in Engineering, 2016, 16(2): 021008.
[16] Wu F, Dantan J Y, Etienne A, et al. Improved Algorithm for Tolerance Allocation Based on Monte Carlo Simulation and Discrete Optimization[J]. Computers & Industrial Engineering, 2009, 56(4): 1402-1413.
[17] Qureshi A J, Dantan J Y, Sabri V, et al. A Statistical Tolerance Analysis Approach for Over-Constrained Mechanism Based on Optimization and Monte Carlo Simulation[J]. Computer-Aided Design, 2012, 44(2): 132-142.
[18] Shen Z, Ameta G, Shah J J, et al. A Comparative Study of Tolerance Analysis Methods[J]. Journal of Computing and Information Science in Engineering, 2005, 5(3): 247-256.
[19] Ghani J A, Choudhury I A, Hassan H H. Application of Taguchi Method in the Optimization of End Milling Parameters[J]. Journal of Materials Processing Technology, 2004, 145(1): 84-92.
[20] Taguchi G, Chowdhury S, Wu Y. Taguchi's Quality Engineering Handbook[M]. New York: Wiley, 2005.
[21] D'Errico J R, Zaino N A. Statistical Tolerancing Using a Modification of Taguchi's Method[J]. Technometrics, 1988, 30(4): 397-405.
[22] Seo H S, Kwak B M. Efficient Statistical Tolerance Analysis for General Distributions Using Three-Point Information[J]. International Journal of Production Research, 2002, 40(4): 931-944.
[23] Johnson N L, Kotz S, Balakrishnan N. Continuous Univariate Distributions[M]. New York: John Wiley & Sons, 1994: 15-25.(编辑:史亚红)　　　　　　　　　　　　　*　收稿日期:2016-11-30；修订日期:2017-02-24。基金项目:国家自然科学基金(51275024)。作者简介:陈志英,男,博士,教授,研究领域为航空发动机结构优化设计、可靠性及维修性工程。