塞式喷管结构对固液火箭发动机的性能影响 *

推进技术 ›› 2018, Vol. 39 ›› Issue (4): 792-801.

塞式喷管结构对固液火箭发动机的性能影响 *

刘和东,田辉

北京航空航天大学宇航学院，北京 100191,北京航空航天大学宇航学院，北京 100191

发布日期:2021-08-15
作者简介:刘和东，男，硕士生，研究领域为固液混合火箭发动机技术仿真分析。

Effects of Aerospike Nozzle Structure on Hybrid Rocket Motor Performance

School of Astronautics，Beijing University of Aeronautics and Astronautics，Beijing 100191，China and School of Astronautics，Beijing University of Aeronautics and Astronautics，Beijing 100191，China

Published:2021-08-15

摘要/Abstract

摘要： 为了分析塞式喷管结构对固液火箭发动机的性能影响，分别设计了使用塞式喷管和钟形喷管的固液火箭发动机。发动机喷管选取了三个不同的扩张比，对应高空和地面两个设计状态。通过数值仿真，预估了发动机的性能，并将使用塞式喷管结构和钟形喷管结构的两种固液火箭发动机进行了对比分析。结果表明:相对于钟形喷管结构，使用塞式喷管结构能够提高固液火箭发动机的燃烧效率和比冲效率，且最大分别提高了4.13% 和3.37%；地面条件下，大扩张比的塞式喷管的仿真推力系数要比同扩张比的钟形喷管的仿真推力系数大2.69%，体现出塞式喷管的高度补偿效应；与钟形喷管内壁面温度相比，塞式喷管塞锥壁面的温度明显更低。

关键词: 塞式喷管；固液火箭发动机；数值仿真；性能

Abstract: In order to analyze the effects of an aerospike nozzle structure on the performance of hybrid rocket motor， aerospike nozzle and bell nozzle were designed respectively. Three different expansion ratios of motor nozzles were selected， corresponding to design conditions of high altitude and ground. The performance of the motors was evaluated with numerical simulation method. Hybrid rocket motors with aerospike nozzle structures were compared with those with bell nozzle structures. The results show that the combustion efficiency and the specific impulse efficiency of hybrid rocket motors with aerospike nozzle structures are respectively 4.13% and 3.37% higher than those with bell nozzle structures at most. Under the condition of ground， the simulated thrust coefficient of aerospike nozzles with a large expansion ratio is 2.69% larger than that of bell nozzles with the same expansion ratio， which reflects the altitude compensation effects of aerospike nozzle. Compared with the temperature of bell nozzle inner wall， the temperature of aerospike nozzle plug wall is significantly lower.

Key words: Aerospike nozzle；Hybrid rocket motor；Simulation；Performance

刘和东,田辉. 塞式喷管结构对固液火箭发动机的性能影响 *[J]. 推进技术, 2018, 39(4): 792-801.

LIU He-dong,TIAN Hui. Effects of Aerospike Nozzle Structure on Hybrid Rocket Motor Performance[J]. Journal of Propulsion Technology, 2018, 39(4): 792-801.

参考文献

[1] 胡建新, 夏智勋. 固液火箭发动机在空间发射上的应用前景[J]. 导弹与航天运载技术, 2002, (3): 25-29.
[2] 蔡国飙. 固液混合火箭发动机技术综述与展望[J]. 推进技术, 2012, 33(6): 831-839. (CAI Guo-biao. Development and Application of Hybrid Ricket Motor Technology: Overview and Prospect[J]. Journal of Propulsion Technology, 2012, 33(6): 831-839.)
[3] 蔡国飙, 李家文, 田爱梅, 等. 液体火箭发动机设计[M]. 北京:北京航空航天大学出版社, 2011.
[4] 任学军, 刘宇, 覃粒子. 环簇式塞式喷管在固体火箭发动机上应用探讨[J]. 固体火箭技术, 2005, 28(3): 184-187.
[5] Russo Sorge A, Carmicino C, Nocito A. Design of a Lab-Scale Cooled Two-Dimensional Plug Nozzle for Experimental Tests[R]. AIAA 2002-4039.
[6] Cedric Oldfield Gould. Design of an Aerospike Nozzle for a Hybrid Rocket[D]. Mississippi: Mississippi State University, 2008.
[7] Patrick Lemieux. Development of a Reusable Aero-Spike Nozzle for Hybrid Rocket Motors[R]. AIAA 2009-3720.
[8] Patrick Lemieux, William R Murray. Nitrous Oxide Cooled, Reusable Hybrid Aerospike Rocket Motor: Experimental Results[R]. AIAA 2012-4201.
[9] Andrew Brock. Aerospike Rocket Motor Structure Webbing[D]. San Luis Obispo: the Faculty of California Polytechnic State University, 2015.
[10] Pablo Sanchez Arribas, Patrick Lemieux, Dario Pastrone. Modeling of N2O Heat Transfer Rates in the Nucleate Boiling Regime, with Experimental Verification[R]. AIAA 2015-3742.
[11] Steven C Shark, Jacob D Dennis, James K Villarreal. Experimental Performance Analysis of a Toroidal Aerospike Nozzle Integrated with a N2O/HTPB Hybrid Rocket Motor[R]. AIAA 2010-6784.
[12] Shannon D Eilers, Stephen A Whitmore, Zachary W Peterson. Regeneratively Cooled Multiple-Use Plug Hybrid for Nanosatellites[J]. Journal of Propulsion and Power, 2013, 29(6).
[13] Gianfranco Angelino. Approximate Method for Plug Nozzle Design[J]. AIAA Journal, 2012, 2(10): 1834-1835.
[14] Immich H, Caporicci M. Status of the FESTIP Rocket Propulsion Technology Program[R]. AIAA 97-3311.
[15] 李新田. 固液火箭发动机装药设计与数值仿真研究[D]. 北京:北京航空航天大学, 2014.
[16] 田辉. 固液混合火箭发动机工作过程数值仿真[D]. 北京:北京航空航天大学, 2005.
[17] 陈懋章. 粘性流体动力学基础[M]. 北京:高等教育出版社, 2002.
[18] 李新田, 田辉, 曾鹏, 等. 固液火箭发动机工作过程三维数值仿真[J]. 航空动力学报, 2012, 27(6):1398-1404.
[19] Chiaverini M J, Kuo K K. Fundamentals of Hybrid Rocket Combustion and Propulsion[M]. Virginia: American Institute of Aeronautics and Astronautics, Inc., 2006.
[20] Versteeg H K, Malalasekera W. An Introduction to Computational Fluid Dynamics: The Finite Volume Method[M]. England: Pearson Education Limited, 2007.
[21] 饶大林, 郑赟韬, 李新田, 等. 固液混合火箭发动机仿真与优化设计[J]. 推进技术, 2010, 31(5): 513-518. (RAO Da-lin, ZHENG Yun-tao, LI Xin-tian, et al. Simulation and Optimization Design of Hybrid Rocket Motor[J]. Journal of Propulsion Technology, 2010, 31(5): 513-518.)
[22] 王鹏飞. 固液混合火箭发动机高效燃烧技术研究[D]. 北京:北京航空航天大学, 2015.
[23] 李宜敏, 张中欣, 张远君. 固体火箭发动机原理[M]. 北京:北京航空航天大学宇航学院, 2012.
[24] 琚春光, 刘宇, 韩非. 塞式喷管性能损失分析[J]. 北京航空航天大学学报, 2005, 31(11): 1222-1225.
[25] 曾鹏. 过氧化氢变推力固液火箭发动机研究[D]. 北京:北京航空航天大学, 2014.
[26] Venkateswaran S, Merkle C L. Size Scale-Up in Hybrid Rocket Motor[R]. AIAA 96-0647.(编辑:朱立影)　　　　　　　　　　　　　*　收稿日期:2017-03-09；修订日期:2017-05-26。作者简介:刘和东,男,硕士生,研究领域为固液混合火箭发动机技术仿真分析。E-mail: peacehnd@163.com