强旋-V型钝体组合燃烧装置绕流实验研究

推进技术 ›› 2018, Vol. 39 ›› Issue (5): 1051-1056.

强旋-V型钝体组合燃烧装置绕流实验研究

李志强,赵冬,吴云柯,何鹏

北京航空航天大学能源与动力工程学院航空发动机气动热力国家级重点实验室，北京 100191,北京航空航天大学能源与动力工程学院航空发动机气动热力国家级重点实验室，北京 100191,北京航空航天大学能源与动力工程学院航空发动机气动热力国家级重点实验室，北京 100191,北京航空航天大学能源与动力工程学院航空发动机气动热力国家级重点实验室，北京 100191

发布日期:2021-08-15
作者简介:李志强，男，博士，副教授，研究领域为高效燃烧技术、涡动力学。E-mail: lizhiqiang@buaa.edu.cn 通讯作者:赵冬，男，硕士生，研究领域为火焰稳定。
基金资助:
国家自然科学基金(51276008)。

Experimental Study on Flow around a V-Type Bluff Body Flame Stabilizer Coupled with Strong Swirling Flow

National Key Laboratory of Science and Technology on Aero-Engine Aero-Thermodynamics，School of Energy and Power Engineering，Beihang University，Beijing 100191，China,National Key Laboratory of Science and Technology on Aero-Engine Aero-Thermodynamics，School of Energy and Power Engineering，Beihang University，Beijing 100191，China,National Key Laboratory of Science and Technology on Aero-Engine Aero-Thermodynamics，School of Energy and Power Engineering，Beihang University，Beijing 100191，China and National Key Laboratory of Science and Technology on Aero-Engine Aero-Thermodynamics，School of Energy and Power Engineering，Beihang University，Beijing 100191，China

Published:2021-08-15

摘要/Abstract

摘要： 为了探明强旋流对钝体绕流旋涡脱落规律的影响，利用PIV速度场仪和高频动态压力传感器等测量仪器研究了强旋-V型钝体组合稳燃装置中旋流器出口安装位置对旋涡脱落频率和尾流流场的影响规律。实验结果表明，当旋流器出口位置安装在钝体内部时，可获得较小的旋涡脱落频率。随着旋流器安装位置向钝体出口方向逐渐移动时，旋涡脱落频率增大。当旋流器出口置于钝体外部时，将破坏钝体剪切旋涡的几何特征，从而导致钝体旋涡脱落机制的改变。另外，当旋流体积流量控制在一定范围(0～1m3/h)内，增大旋流流量有助于减小钝体绕流剪切旋涡的脱落频率，对比无旋流时的V型钝体绕流，当旋流流量为1m3/h时，旋流器出口位置位于钝体尾缘内部1倍开口直径处的V型钝体绕流St数下降幅度最大，约为34.96% 。一定范围内的旋流同样有利于扩大回流区，在旋流流量为0.5m3/h时回流区长度达到最大，约为钝体开口直径的2.3倍。但当旋流体积流量过大时，将导致下游流动恶化，钝体的火焰稳定性能可能会急剧下降。

关键词: 旋流；钝体绕流；旋涡脱落；回流区；火焰稳定器

Abstract: In order to explore the effects of strongly swirling flow on the vortex shedding patterns around the V-type bluff body，the effects of the installation position of the swirler outlet in the combined flame stabilizer on the vortex shedding frequency and the wake flow field are studied by using the PIV velocimetry and the high frequency dynamic pressure sensor. Compared with the V-type bluff body without swirling flow，the experimental results show that the vortex shedding frequency can be decreased when swirling is added. With the installation position of the swirler outlet moves toward the outlet position of the blunt body，the shearing vortex shedding frequency of the V-type bluff body increases gradually. When the swirler outlet is located outside of the bluff body，the geometrical characteristics of the shear vortex will be destroyed，which will lead to the change of the vortex shedding mechanism. Moreover，when the swirling volume flow rate is controlled within a certain range(0～1m3/h)，increasing the swirl flow rate can reduce the shedding frequency of the shearing vortex around the bluff body. Compared with the case of V-type bluff body without swirling flow，the largest drop of the St number，about 34.96% ，occures in the case under the 1m3/h swirling volume flow rate condition when the swirler outlet is located 1 time of the opening diameter at the trailing edge in the bluff body. A certain range of swirl flow is also helpful to expand the recirculation zone. When the swirl flow rate is 0.5m3/h，the length of the recirculation zone reaches the maximum，which is about 2.3 times of the opening diameter. However，when the swirling volume flow rate is beyond a certain range，the wake flow field becomes deterioration，which is possible to influence the flame stability of the combined flame stabilizer.

Key words: Swirling flow；Flow around a bluff body；Vortex shedding；Recirculation zone；Flame Stabilizer

李志强,赵冬,吴云柯,何鹏. 强旋-V型钝体组合燃烧装置绕流实验研究[J]. 推进技术, 2018, 39(5): 1051-1056.

LI Zhi-qiang,ZHAO Dong,WU Yun-ke,HE Peng. Experimental Study on Flow around a V-Type Bluff Body Flame Stabilizer Coupled with Strong Swirling Flow[J]. Journal of Propulsion Technology, 2018, 39(5): 1051-1056.

参考文献

[1] 唐豪杰, 郑韫哲, 张彤枫, 等. 钝体燃烧器中心射流火焰不稳性机理实验研究[J]. 推进技术, 2013, 34(5): 672-679. (TANG Hao-jie, ZHENG Yun-zhe, ZHANG Dan-feng, et al. Experiments on Mechanisms of Unstable Flames in Bluff-Body Burner with a Central Fuel Jet [J]. Journal of Propulsion Technology, 2013, 34(5): 672-679.)
[2] 尹航, 钟仕立, 戴韧, 等. 钝体燃烧器湍流预混燃烧流动特性分析[J]. 动力工程学报, 2012, 32(2): 101-105.
[3] 张洪滨, 王纪根. 双V型火焰稳定器的研制和应用[J]. 推进技术, 1994, 15(3): 38-43. (ZHANG Hong-bin, WANG Ji-gen. Development and Application of Double V Type Flame Stabilizer [J]. Journal of Propulsion Technology, 1994, 15(3): 38-43.)
[4] 柳杨, 金捷, 王慧汝, 等. 新型变几何火焰稳定器燃烧特性试验[J]. 航空动力学报, 2012, 27(10): 2214-2221.
[5] Raffoul C N, Nejad S A, Spring S A. Entrainment and an Mixing Characteristics of Bluff Body Flameholders,an Experimental and Numerical Study[R]. AIAA 94-10.
[6] Barry Kiel, Kyle Garwick, Amy Lynch, et al. Non-Reacting and Combusting Flow Investigation of Bluff Bodies in Cross Flow[R]. AIAA 2006-5234
[7] Barry Kiel, Kyle Garwick, Dr James R Gord , et al. A Detailed Investigation of Bluff Body Stabilized Flames [R]. AIAA 2007-0168.
[8] 刘宜临. 火焰稳定器后动态流场研究[D]. 南京:南京航空航天大学, 2009.
[9] 岳连捷, 杨茂林. 火焰稳定器稳焰机理的非定常观点探讨[J]. 航空动力学报, 2001, 16(4): 340-344.
[10] 韩启祥, 范育新, 张净玉, 等. 燃烧理论基础[M]. 南京:南京航空航天大学出版社, 2007.
[11] 黄勇. 燃烧与燃烧室[M]. 北京:北京航空航天大学出版社, 2009.
[12] Bing Ge, Shu-Sheng Zang. Experimental Study on the Interactions for Bluff-Body and Swirl in Stabilized Flame Process[J]. Journal of Thermal Science, 2012, 21(1): 88-96.
[13] 唐杨杨, 李志强, 邸亚超, 等. 方柱-强旋组合旋涡脱落机制研究[J]. 推进技术, 2014, 35(8): 1023-1029. (TANG Yang-yang, LI Zhi-qiang, DI Ya-chao, et al. Study on Vortex Shedding Mechanism of Square Cylinder Coupling with Strong Swirl Flow[J]. Journal of Propulsion Technology, 2014, 35(8): 1023-1029.)
[14] DONG Gan, LI Zhi-qiang, ZHANG Zhi-hong. Study on the Vortex Shedding Mechanism of Coupling Combustion Stabilizer with V-Gutter and Strong Swirl Flow[C]. Shanghai: 2014 Asia-Pacific International Symposium on Aerospace Technology, 2014.
[15] 张志博, 于贤君, 刘宝杰. 压气机转子内部流场SPIV测量的精度分析[J]. 航空动力学报, 2010, 25(4):868-876.(编辑:史亚红)　　　　　　　　　　　　　*　收稿日期:2017-03-24；修订日期:2017-07-03。基金项目:国家自然科学基金(51276008)。作者简介:李志强,男,博士,副教授,研究领域为高效燃烧技术、涡动力学。E-mail: lizhiqiang@buaa.edu.cn通讯作者:赵冬,男,硕士生,研究领域为火焰稳定。E-mail: 291664683@qq.com